SONOFF M5 SwitchMan Smart Wall Watch User Manual

SONOFF M5 SwitchMan Smart Wall Watch

Product Introduction

The device’s weight is less than 1 kg. An installation height of fewer than 2 is recommended.

Features

This device is a smart physical wall switch. After pairing it with eWeLinkApp, you can turn on/off the connected devices via the smartphone wherever you are, schedule its on/off, share it with your families to control together, etc.

• Remote Control
• Single/Countdown
• Timing
• Voice Control
• Share Control
• Smart Scene
• Inching Mode
• Camera Linking
• Group Control
• History Operation Record
• LAN Control

Operating Instruction

• Power off Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on! ****
• Wiring instruction Light fixture wiring instruction:  Make sure all wires are connected correctly.
• Download the eWelink App
• Power on After powering on, the device will enter the Bluetooth Pairing Mode during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash and release. The device will exit the Bluetooth Pairing Mode if not paired within 3mins. lf you  want to enter this mode, please long press any pairing button for about Ss until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release.
• Add device Tap “+” and select “Bluetooth Pairing”, then operate following the prompt on the App.

Compatible Pairing Mode

If you fail to enter Bluetooth Pairing Mode, please try “Compatible Pairing Mode ” to pair.

1. Long press any Pairing button for Ss until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press any Pairing button for Ss again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode.
2. Tap”+” and select ” Compatible Pairing Mode ” on App. Enter Wi-Fi password, tap “Next” and then “Connect”. Select Wi-Fi SSID with ITEAD-** and enter the password 12345678, and then go back to eWeLink app and tap “Next”. Be patient until pairing completes.

Specifications

Model

| MS-1 C-80, M5-2C-80, M5-3C-80

MS-1 C-86, M5-2C-86, M5-3C-86

---|---

Input

| 1C:100-240V – 50/60Hz 1 0A Max

2C: 100-240V –  50/60Hz 1 0A Max

3C: 100-240V – 50/60Hz 6A Max

Output

| 1C:100-240V – 50/60Hz 10A Max

2C: 100-240V- 50/60Hz SA/Gang 1QA/Total Max

3C: 100-240V – 50/60Hz 2A/Gang 6A/Total Max

Max. load

| 1C: 2200W

2C: 2200W(1-11 00W/Gang)

3C: 1320W(1-440W/Gang)

LED load

| 1C: 300W/220V, 1SOW/11 0V

2C: 300W/220V/Gang, 1SOW/11 0V/Gang

3C: 100W/220V/Gang, 600W/11 0V/Gang

Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
Bluetooth Standard| 4.2 BLE
App operating systems| Android & iOS
Working temperature| -10″C~40″C
Shell material| PCV0

Dimension

| 80: 86×71 x41.5mm

86: 86x86x41.5mm

Wi-Fi LED indicator status instruction

Serve
Flashes quickly three times| Firmware Updating**

Factory Reset

Deleting the device on the eWeLink App indicates you restore it to factory setting.

Common Problems

Fail to pair Wi-Fi devices with eWeLink APP

1. Make sure the device is in pairing mode. The device will automatically exit the pairing mode if not paired within 3mins.
2. Please turn on the location service on your mobile phone and give permission. Before choosing the Wi-Fi network, the location service should be turned on and the permission is given. Location information permission is used to obtain Wi-Fi list information. If you tap “Disable”, the device will not be added.
3. Make sure your Wi-Fi network runs on the 2.4GHz band.
4.  Make sure you entered a correct Wi-Fi SSID and password, no special characters are contained.A wrong password is a very common reason for pairing failure.
5.  You may getthe device close to the router for a good signal transmission while pairing.
6. Please try to pair the device in the compatible mode.

Wi-Fi devices “Offline” issues

Please check the following issues by the Wi-Fi LED indicator status: The LED indicator blinks once every 2s means you fail to connect to the router.

1. Maybe you entered the wrong Wi-Fi SSID and password.
2. Make sure your Wi-Fi SSID and password don’t contain special characters, for example, the Hebrew, Arabic characters. Our system can’t recognize these characters so they fail to connect to the Wi-Fi.
3. Maybe your router has a lower carrying capacity.
4. Maybe the Wi-Fi signal strength is weak. Your router is too far away from your device, or there may be some obstacles between the router and the device so that the signal transmission is blocked.
5. Be sure that the MAC of the device is not on the blacklist of your MAC management.

The LED indicator flashes twice on repeated means you fail to connect to the server.

1. Make sure the Internet connection is normal. You can use your phone or PC to connect to the Internet, and if you fail to access, please check the availability of the Internet connection.

2. Maybe your router has a low carrying capacity. The number of devices connected to the router exceeds its maximum value. Please check the maximum number of devices that your router can carry. If the number of connected devices exceeds the maximum value, please delete some devices or change a lager router and try again.
   3. Please contact your ISP and confirm our server address is not shielded:

   • cn-disp.coolkit.cc (China Mainland)
   • as-disp.coolkit.cc (in Asia except China)
   • eu-disp.coolkit.cc (in EU)
   • us-disp.coolkit.cc (in US)

If none of the above methods solved this problem, please submit your issue via help &feedback on the eWeLink App. Hereby, Shenzhen SonoffTechnologies Co., Ltd. declares that the radio equipment type MS-1 C-80, M5-2C-80, M5-3C-80, MS-1 C-86, M5-2C-86, M5-3C-86 are in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https:/ /son off. tech/usermanuaIs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>