SEBO Duo Carpet |And Upholstery Dry Cleaning System Owner’s Manual
- July 15, 2024
- SEBO
Table of Contents
- SEBO Duo Carpet |And Upholstery Dry Cleaning System
- Product Information
- Product Usage Instructions
- Technical Details
- Wiring Diagram
- IMPORTANT SAFETY INSTRUCTIONS
- SEBO Duo Carpet Cleaning System Product Features
- Identification of Parts
- Assembly
- Operating Instructions
- How to use the duo Cleaning System
- Maintenance
- Trouble-Shooting Guide
- Parts List
- Warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SEBO Duo Carpet |And Upholstery Dry Cleaning System
Product Information
Specifications
- Brush motor: 1.8 amps
- Width: 14 inches
- Height: 4-11/16 inches
- Body weight: 11 lbs.
- Brush speed: 400 rpm
- Cord length: 40 feet
- Power supply: 120 VAC, 50-60 Hz
Product Usage Instructions
Important Safety Instructions
Before using the SEBO Duo Brush Machine, read and follow all safety
instructions provided in the manual. Some key safety points include:
- Unplug the machine when not in use or during servicing.
- Avoid outdoor or wet surface usage.
- Keep away from small children and pets.
- Use only as described in the manual with recommended attachments.
- Do not use it if the cord or plug is damaged.
Assembly
Follow the assembly instructions provided in the manual to correctly set up
the SEBO duo Brush Machine before use.
Operating Instructions
Refer to the operating instructions section in the manual for detailed steps
on how to operate the duo Cleaning System effectively.
Maintenance
Regular maintenance is essential for optimal performance. Follow these steps:
- Removing the brushes: Refer to the manual for instructions on removing the brushes for cleaning or replacement.
- Cleaning the brushes: Keep the brushes clean to ensure efficient cleaning results.
- Replacing the brushes: When necessary, replace worn-out brushes following the manual guidelines.
Troubleshooting Guide
If you encounter any issues with the machine, consult the Troubleshooting
Guide in the manual for solutions to common problems.
FAQ
-
Q: Can I use the SEBO duo Brush Machine outdoors?
A: No, it is recommended to use the machine indoors only and avoid wet surfaces. -
Q: How often should I clean the brushes?
A: It is advisable to clean the brushes regularly to maintain optimal cleaning performance. Follow the maintenance instructions in the manual.
Technical Details
- Brush motor 1.8 amps
- Width 14 inches
- Height 4-11/16 inches
- Body weight 11 lbs.
- Brush speed 400 rpm
- Cord length 40 feet
- 120 VAC 50-60 Hz
Wiring Diagram
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
When using an electrical appliance, basic precautions must always be
followed.
To reduce the risk of electric shock, this brush machine has a polarized plug;
one blade is wider than the other. This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way. Connect only to the outlet
type specified on the serial number plate underneath the machine.
SAVE THESE INSTRUCTIONS.
WARNING:
To reduce the risk of fire, electric shock, or injury:
- Do not leave the brush machine while plugged in. Unplug from the outlet when not in use and before servicing.
- Do not use it outdoors or on wet surfaces.
- Do not use near small children or pets. Do not allow it to be used as a toy. Use of this product by children should always be supervised by an adult.
- Use only as described in this manual. Use only manufacturer-recommended attachments.
- Do not use a damaged cord or plug. If the brush machine is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a SEBO service center.
- Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the machine over the cord. Keep the cord away from heated surfaces.
- Do not unplug by pulling on the cord. To unplug, grasp the plug – not the cord.
- Do not plug in if the switch is in the “I” (ON) position.
- Do not use outlets above counters to plug in the brush machine – damage to items in the surrounding area could occur.
- Always carry the machine over steps and sills.
- Do not handle the plug or vacuum handle with wet hands.
- Do not put any objects into machine openings. Do not use the machine with any openings blocked. Keep openings free of lint, hair, and anything that may reduce airflow.
- Do not remove any screws from the machine.
- Do not run the machine over anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Turn off all machine controls before unplugging.
- Use extra care when cleaning on stairs.
- Do not turn on the machine with the storage tray still attached.
- Do not use a machine to clean up flammable or combustible liquids such as gasoline or use in areas where they may be present.
- Machines can cause a fire when operated near flammable vapors or materials. Do not operate this machine near flammable fluids, dust, or vapors.
- Maintenance and repairs must be done by qualified personnel.
- Use only original SEBO replacement parts.
- Do not use a machine as a step.
- Do not leave the machine standing in one place with the machine turned on. This may damage the carpet.
- Keep hair, loose clothing, fingers, and all parts of the body away from machine openings and moving parts. Do not place fingers or other body parts under the machine, unless it is unplugged.
- Do not place the brush head over the fringes on a carpet or rug.
- Store the brush machine in a dry place at room temperature. When the machine is not in use, you should wrap the cord on the cable hooks.
- Any other servicing should be performed by an authorized service representative.
WARNING!
The quality, condition, coating, texture, age, and manufacturing technique
of all floor surfaces vary. Therefore, machines with rotating brushes,
including your SEBO duo brush machine, may damage some floor coverings or
surfaces. Berber carpets, long shag, specialty, and delicate or hand-woven
carpets are particularly vulnerable to damage by rotating brushes. Always
consult the materials supplied by your floor’s manufacturer for information on
proper upkeep and cleaning. To ensure that your new SEBO duo brush machine is
compatible with your floor coverings, please test the duo-P cleaner and brush
machine on each type of carpeting in a small inconspicuous area to determine
if any damage occurs. If damage occurs, stop using the brush machine and
powder immediately!
An operating machine should not stand stationary on the floor for inappropriate periods. Damage could occur. Do not run the machine on flooring not covered by carpet.
SEBO Duo Carpet Cleaning System Product Features
Your SEBO duo Cleaning System is formulated to deep clean your entire carpet or spot clean stubborn stains without soaking your carpet. Dry cleaning is safer for most carpets – it will not shrink the carpet or cause water staining if applied unevenly. SEBO duo-P Cleaning Powder leaves no detergent residue to cause your carpet to resoil, and the carpet can be used immediately after cleaning. Because this is a DRY cleaning process, the SEBO duo-PCleaning Powder will not promote the growth of mold and fungus in your carpet and pad that wet extraction systems may cause. In addition, the GAF allergy research center in Germany found in a long-term test that, six months after a single cleaning with duo-P, seven out of ten carpets remained free of dust mite allergens.
The Advantages of using the SEBO Duo Cleaning System are:
- No detergent residue
- Alleviates house dust allergies
- Easy spot cleaning
- A built-in fiber protector helps to protect your carpet against future stains and soil
- No shrinkage or mildew
- No need to move furniture
- Cleans most types of carpets
- Immediate use of the carpet
How it Works:
- The SEBO duo-P Cleaning Powder is made up of granules that are moistened with detergent and are environmentally friendly and safe to use. When the granules are worked into the carpet fiber, soil, and stains are lifted out of the carpet by the duo-P powder. The duo Brush Machine lifts the carpet pile ensuring all surfaces of the fiber are cleaned, leaving your carpet revived and softer. After vacuuming, the duo-P powder is removed, and your carpet is left clean, dry, and ready for use.
- An added advantage in using duo-P Cleaning Powder on your carpet is that once applied, a built-in fiber protector will help to protect against future damage from soiling or staining.
The duo-P Cleaning Powder:
- Refill boxes are available as a single (1.1 lb.) or a multiple with five (1.1 lb each) packs. Each single pack can cover up to 250 square feet of carpet.
- The SEBO duo-P Clean Box contains a 1.1 lb. pack in an environmentally friendly refillable container, and the underside of the lid has a built-in brush for spot cleaning! When you have used the contents, you can replace the inner bag with an inexpensive refill pack of duo-P Cleaning Powder.
- The SEBO duo Accessory Brush is perfect for cleaning small areas such as entryways and stairs.
Identification of Parts
- Handle
- On/Off switch
- Cable hooks
- Handle connector
- Swivel neck
- Brushes
- Storage tray
- Spot cleaning brush
Standard Accessories
- 7. Storage tray
- 8. Spot cleaning brush
- 9. duo-P Cleaning Powder
Assembly
Press the plunger button (10) and insert the handle (1) into the swivel neck (5). With the plunger button released, the handle should remain firmly engaged. Pushing the handle forward sets the handle into the storage position. Pulling back releases the handle into the operating position.
Operating Instructions
Before turning on your brush machine, remove the machine from the storage tray (7) by pressing down the catch (15) and lifting the machine upwards by the handle (figure 1).
- To replace the machine into the storage tray after use, first unplug the machine, then lower the head onto the tray until the tray snaps into place (figure 2).
Starting The Machine
Before turning on your brush machine, make sure that the storage tray has been removed (see above) and that you have a firm hold on the handle grip to keep the machine from moving forward.
-
Turn the quick-release cable hook (14) to the up position by moving it to the left or right.
-
Release the power cord plug from the power cord and lift the cord (13) off of the upper cord hook.
-
With the switch (2) in the “O” (OFF) position, plug the polarized power cord into a 120-volt outlet located near the floor.
Switch Position- O = OFF
- I = ON
How to use the duo Cleaning System
To Clean the Entire Carpet – Figures 1, 2 & 5
- First, vacuum your carpet prior to applying duo-P Powder. Then, spread duo-P Cleaning Powder evenly over the carpet. This can be done by spreading the powder directly out of the bag, or by spreading the powder by hand. Distribute the powder lightly, but evenly, over the area to be cleaned (figure 1). You need not use an excessive amount of powder for effective cleaning.
- Work the powder into the carpet using the SEBO duo Brush Machine, which opens the carpet pile enabling the duo-P powder to clean around each separate fiber (figure 2).
- Once the duo-P powder has absorbed all of the dirt and the area is dry to the touch (approximately 30 minutes), simply vacuum the area thoroughly (figure 5).
To Spot Clean Stains – Figures 3, 4 & 5
- Vacuum any loose dirt or debris from the area. If the soiled area is wet, use white paper towels to absorb all moisture from the carpet. This will prevent the powder from “caking up” on the carpet and the brush. Then, spread a small amount of duo-P powder onto the soiled area.
- Gently work the powder into the carpet using the spot cleaning brush (page 5, #8), the brush provided with the SEBO Clean Box (figure 3), or the accessory brush (figure 4). Older or more stubborn stains may require further treatments. Simply repeat the process until the stain is completely removed.
- Once the duo-P powder has absorbed all of the dirt and the area is dry to the touch (approximately 30 minutes), simply vacuum the area thoroughly (figure 5).
Important Product Tips:
- For best results, vacuum the carpet before applying duo-P powder.
- Check a small, inconspicuous area of the carpet for colorfastness.
- Absorb any moisture from the carpet using white paper towels before applying duo-P powder.
- Open the window to speed drying.
- Reseal the package after opening to maintain moisture. To ensure the longer life of the powder, seal all opened packages inside of a zip-lock bag.
- Only moist powder will effectively clean. If powder becomes dry before it is used (e.g. powder left in an opened package), it will no longer work.
- Before using the SEBO duo-P Powder on your carpets, please read all instructions and warnings provided with the powder and all the instructions and warnings in this manual.
- Limited suitability for Berber and needle punch carpets.
- Use caution if cleaning Berber or looped pile carpeting with the brushing machine or when using hand brushes. Test an inconspicuous area to determine suitability. Do not use on hand-woven or dyed carpeting. Check with the carpeting manufacturer for approved cleaning methods.
Maintenance
Always unplug the brush machine from the outlet before dismantling any part of the machine!
Removing the Brushes to Change or Clean – Figures 7 & 8
Remove the brushes (6), by unscrewing the two screws (17) at the end of each brush from the bearing block (18). Do not remove the screws that are recessed. Push the top of the brush and the block forward at the same time. Take the block off the brush, then, lift the brush upwards out of the brush housing.
Cleaning the Brushes
The brushes must be removed from the machine to be thoroughly cleaned. See the
instructions above for removing the brushes. Clean by running your SEBO
vacuum’s suction hose, with a crevice tool attached, up and down each brush to
remove dirt and powder. Some carpet fibers, dirt, and debris may require
removal by hand. Replace the brushes – see instruc-tions below.
A cursory cleaning of the brushes may be done without removing them, by
unplugging the machine, turning the brush rollers upright, and using your
vacuum’s suction hose, with a crevice tool attached, to remove the loose dirt
or powder.
Replacing the Brushes – Figures 8 & 9
To replace each brush, insert the end with the slots into the housing and locate the slots over the drive cog (19) by turning the brush. Push the brush forward slightly to enable the bear-ing block (18) to be replaced, then push the block back into place in the brush housing and replace the two screws (17).
One Replacement Brush
Part #3005 ER
Trouble-Shooting Guide
Always unplug the brush machine from the outlet before dismantling any part of the machine!
Trouble-Shooting Guide
Always unplug the brush machine from the outlet
before dismantling any part of the machine!
PROBLEM| REASON| SOLUTION
Does not turn on or the machine shuts off
intermittently| 1. The handle is not fully inserted into the housing,
causing a faulty connection.| 1. See page 5 for how to insert the handle.
2. Not plugged into a good outlet.| 2. Use another outlet.
3. Cable worn.| 3. Replace cable.
4. The brush has not been reinserted properly.| 4. See page 8 for how to
replace the brush.
5. Defective switch.| 5. Return to your authorized SEBO dealer for repair.
Parts List
Pos.
| Part #| Description| Pos.| Part #|
Description
---|---|---|---|---|---
1| 1030 UL| Cable clamp| 37| 3038| Drive belt
2| 0106| Screw 3.9 x 13 A2| 38| 0116| Screw M4 x 30 A2
3| 3125| Handle cable| 39| 3004 SE| Cover
5| 3137 DG| Switch cap| 41| 0149| Spacer washer
6| 3136 HG| Switch cap holder| 44| 2438 HG| Plunger button, complete
7| 0127| Screw taptite M4 x 10| 45| 2423| Spring
9| 5353 HG| Cable| 47| 2022 HG| Swivel neck cover
10| 3055 HG| Spot cleaning brush| 48| 3111 HG| Swivel neck complete
11| 3142 HG| Handle grip| 50| 3051| Swivel neck support
12| 0532 ER| Rocker switch| 51| 3014| Motor pulley
13| 0105| Screw 3.9 x 19| 52| 3030| Clamp
14| 5352 HG| Clamp| 53| 3013| Pulley
15| 0129| Screw taptite M4 x 12| 54| 3042| Drive belt
16| 3115| Handle| 55| 3022| Gear wheel
17| 3118 HG| Cable hook| 56| 3036| Spacer
19| 3027 HG| Handle connector cover| 57| 3037| Shaft RH
20| 3113 HG| Handle connector| 58| 0222| Ball bearing
21| 1020 UL| Contact cover| 59| 3015| Pulley
22| 0103| Screw 3.9 x 16| 60| 3039| Bridge
23| 3122/H| Handle cpl.| 61| 3035| Shaft LH
25| 3033| Storage tray| 62| 3021| Gear wheel
26| 2007 MG| Bumper| 63| 3018| Pulley
27| 3005 ER| Brush assembly| 64| 3071| Clip
28| 3002 SW| Base plate| 65| 3040| End plate
29| 0112| Screw M4 x 10 A2| 66| 3009| Pulley
30| 3010 HG| Bearing block RH| 67| 3028| Spring
31| 3001 HG| Brush housing| 68| 3007| Brush drive cog
32| 3032| Handle stop spring| 69| 3074 HG| Bearing block
33| 0502| Terminal block| 70| 3052 HG| Bearing block assembly LH
34| 3049 ER| Motor 120 V| 71| 3017| Pulley
| 05084 S| Carbon brush set| 72| 3056| Pulley 12R/Ms
35| 0141| Locking washer| | |
Warranty
Three Years Non-Wear Parts – One Year Labor
-
Your authorized SEBO dealer or SEBO will provide the original product purchaser with the replacement of Non-Wear Parts which fail due to a material or workmanship defect for three (3) years from the original date of purchase of the new product.
-
Your authorized SEBO dealer or SEBO will repair (or SEBO will cover labor charges associated with repair) a defective SEBO Brush machine at no cost to the original purchaser, within one (1) year of the original purchase of the new product.
-
SEBO America, Floor Care Equipment, Ltd., or an authorized SEBO dealer must complete all warranty repairs.
-
To locate an authorized SEBO dealer in your area, or to register a warranty claim in the United States of America, please call SEBO America at
800-334-6614. -
To locate an authorized SEBO dealer or to register a warranty claim in Canada, please call Floor Care Equipment, Ltd. at 800-661-8687.
-
The warranties provided for above apply exclusively to SEBO Brush Machines which are used residentially. No warranty is provided for SEBO Brush Machines used commercially.
-
The worn parts excluded from warranty coverage include the cable (external cord), the brush rollers, and the spot-cleaning brush.
-
This warranty applies only while your SEBO Brush Machine is physically located within the United States of America and its territories or Canada.
-
The purchase receipt showing the date, price, and item of purchase is the initial document of proof of purchase and determines the validity of the warranty. To be certain that your warranty claim can be processed as quickly and efficiently as possible, please retain your original purchase receipt and mail in the warranty card provided with your new SEBO Brush Machine.
-
This warranty gives you specific legal rights. You may also have other legal rights, which vary from state/province to state/province.
-
SEBO America will not process nor will it accept responsibility for warranty claims for machines purchased from dealers located in Canada.
Floor Care Equipment, Ltd. will not process nor will it accept responsibility for warranty claims for machines purchased from dealers located in the United States.
EXCLUSIVE REMEDY:
The remedies provided under the terms of this Warranty are the purchaser’s
exclusive remedies and are instead of any other remedies otherwise available.
THE WARRANTY DOES NOT COVER:
- Used or secondhand products.
- Products outside of the warranty period.
- Items not manufactured by SEBO.
- Normal maintenance service.
- Equipment damaged by improper use, accident, other casualty, or negligence.
- Machines equipped with nonauthorized attachments or modifications.
- Machines on which the serial number has been altered or removed.
LIMITATIONS AND EXCLUSIONS:
- SEBO MAKES NO OTHER REPRESENTATIONS OR WARRANTIES, EXPRESSED OR IMPLIED, AND SPECIFICALLY EXCLUDES THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- SEBO WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE.
- THIS DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO THE EXTENT SAID DISCLAIMER IS NOT ALLOWED BY APPLICABLE STATE/PROVINCIAL LAW.
To contact SEBO in the United States of America:
- SEBO America, LLC
- Telephone: 800-334-6614 • 303-792-9181
- Fax: 303-792-9196
- E-mail: info@sebo-vacuums.com
- Website: www.sebo.us
To contact SEBO in Canada:
- Floor Care Equipment, Ltd.
- Telephone: 800-661-8687 • 403-250-5005 Fax: 403-250-5057
- E-mail: fcequip@shaw.ca.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>