BLACK HORSE PR-JPGC79 Premium Running Boards Instruction Manual

BLACK HORSE PR-JPGC79 Premium Running Boards

Product Information

Specifications:

• Part Number: PR-JPGC79
• Manufacturer: Black Horse Off Road
• Material: Steel
• Color: Black
• Weight: Varies based on model

Product Usage Instructions

Installation Instructions:

Parts List:

• 1 Driver/Left Running Board
• 1 Passenger/Right Running Board

Installation Steps:

1. Begin with the Driver/Left side. Attach the Driver/Left Front Mounting Bracket using the provided hardware.
2. Proceed to attach the Driver/Left Rear Mounting Bracket following the same procedure.

Maintenance Instructions:
To protect your investment, do not use any polish or wax-containing abrasives that could damage the finish. Mild soap can be used to clean the Running Boards.

FAQ (Frequently Asked Questions)

• Q: How often should I inspect the installation?
  A: Periodic inspections should be done to ensure all hardware remains secure and tight. We recommend checking every few months or after driving on rough terrain.

• Q: Can I install the running boards myself?
  A: While the installation process can be done at home, we recommend seeking professional assistance if you are not familiar with automotive installations.

PARTS LIST

PROCEDURE

1. REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND TYGER FURY STEPS.
2. Starting on the Driver/Left front of the vehicle, remove the cover on the bottom of the vehicle. Select the Driver/Left Front Mounting Bracket. Attach the Mounting Bracket to the threaded insert in the front location with (1) 12mm Hex Bolt, (1) 12mm Lock Washer and (1) 12mm Flat Washer, (Figures 1 & 2). Do not tighten the hardware.
3. Attach the Mounting Bracket to the pinch trim with (1) 6mm Hex Bolt, (2) 6mm Flat Washer, (1) 6mm Lock Washer and (1) 6mm Hex Nut, (Figure 3). Do not tighten the hardware.
4. Move along the body panel to the center mounting location, (Figure 4). Select the Drier/Left Center Mounting Bracket. Repeat Step 2 to install the Bracket, (Figures 3 & 4). Do not tighten the hardware.
5. Continue to the rear mounting location in front of the rear tire, (Figure 5). Select the Driver/Left Rear Mounting Bracket. Attach the Bracket to the threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figures 5 & 6). Do not tighten the hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
6. Select the Driver/Left Viewpoint Running Board. Insert (6) T-Bolts into the channels in the bottom of the Running Board, (3) per channel, (Figure 7). Place the Running Board onto the Mounting Brackets and line up the T-Bolts. Attach the Running Board to the Mounting Brackets with (6) 6mm Flat Washers, (6) 6mm Lock Washers and (6) 6mm Hex Nuts, (Figure 8). Do not tighten the hardware.
7. Level and adjust the Running Board and tighten all hardware.
8. Move to the Passenger/Right side. Repeat Steps 2,3 & 5 to attach the Passenger/Right Front and Rear Mounting Brackets.
9. Locate the center mounting location, (Figure 9). Select the Passenger/Right Center Mounting Bracket. Hold the Bracket and line up to the hole in the pinch trim to the lower slot in the top of the Bracket. Mark where the top slot is located on the floor panel. Using a 1/2” drill bit, (not included) to drill through only the bottom layer of the floor panel.
10. Select the 10mm Threaded Insert and the 10mm Insert Tool. Push the Tool and Insert the assembly into the factory hole. NOTE: If the Insert fits too tight, lightly tap it into place with a small hammer.
11. Firmly hold the handle on the Tool and tighten the hex bolt in the Insert until it is fully collapsed and locked in place, (Figures 10 & 11). NOTE: Do not over-tighten the Insert or a pull out may occur. Once the Insert is collapsed, remove the tool from the Insert.
12. Attach the Passenger/Right Center Mounting Bracket to the Threaded insert with (1) 10mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer. Do not tighten the hardware. Repeat Step 3 to attach the Bracket to the pinch trim.
13. Repeat Steps 6 & 7 to attach the Passenger/Right Running Board. Do not tighten the hardware.
14. Level and adjust the Running Board and tighten all hardware.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
    To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Running Boards.

Driver Side Installation Pictured

Passenger Side Installation Pictured

• Select Insert Tool and (1) Insert. Thread Insert onto the end of Insert Tool. Hand tighten only, do not tighten the hex bolt
• Firmly hold the assembly and push Insert into a drilled hole.
• Hold the Tool Assembly up tight in the body panel. Turn the hex bolt in the Tool clockwise to expand the insert in the body panel. Remove the Tool once the Insert is fully tightened. Do not overtighten or Insert may be damaged.

1-866-926-2867 | 39 St. Mary’s Place, Freeport, NY 11520 |
www.blackhorseoffroad.com

References

• Black Horse | Home Page

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>