Lowe s 6248254 Swivel Joint Lamp Installation Guide
- June 1, 2024
- Lowe s
Table of Contents
Lowe s 6248254 Swivel Joint Lamp
Specifications
- Item Number : 6248254
- Voltage: 120V
- Maximum Wattage: Type A, Max 60W per bulb
Product Information The product is a lamp assembly designed for installation on ceilings or walls. It includes various parts such as a mounting plate, canopy, swivel joint, arms assembly, lampshades, and sockets. The lamp requires Type A bulbs with a maximum wattage of 60W per bulb and operates on 120V voltage.
Product Usage Instructions
- Prepare the required tools including a ladder, Phillips head or flat blade screwdriver, electrical tape, pliers, and wire cutter/stripper.
- Ensure the electricity is turned off before starting any installation work.
- Carefully unpack the fixture and verify all parts are included as per the provided illustration.
- Attach the mounting plate and pass the fixture wires through the tubes, swivel joint, and canopy.
- Tighten all threaded pipes and connect the tubes to the swivel joint and arms assembly.
- Connect wires following the provided wiring connection charts.
- Ensure ground wires are connected properly using the green ground screw.
- After wiring, attach the lampshades and sockets to complete the assembly
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED
TOOLS REQUIRED (NOT INCLUDED)
PARTS
PARTS TYPE & QTY INCLUDING
- (C) Mounting plate (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Swivel joint (1)
- (G) Knob nut (2)
- (H) Tube
- (I) Arms assembly (1)
- (J) Arm (3)
- (K) Socket ring (3)
- (L) Lampshade (3)
- (M) Socket (3)
ACCESSORIES & QTY ENCLOSED
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Unscrew knob nuts (G) from the canopy (E).
- Remove mounting plate (C).
- Adjust arms (J) to a vertical angle.
- According to your desired hanging height to choose and use tubes (H).
- Then pass the fixture wires through the chosen tubes (H), swivel joint (F) and canopy (E).
- Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto the swivel joint (F) and the top of the arms assembly (I). Hanstraightens till snug.
- Attach mounting plate (C) to the outlet box with mounting screws (B).
- Make wire connections Connect wires as below wires connection shown below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre-assembled screws in mounting plate (C).
Note: canopy (E) should be snug against the ceiling and knob nuts (G). If not, adjust the threaded length on the mounting plate (C):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled screws in or out of the mounting plate (C).
- When the secure length is achieved, tighten the hex nuts and back to step 8.
Remove socket rings (K) from sockets (M).
- Place lampshades (L) on sockets (M).
- Screw socket rings (K) to sockets (M) to secure lampshades (L).
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.
Check everything is already installed properly, and then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>