Lowe s 6248246 Chandelier Light Fixture Instruction Manual

Lowe s 6248246 Chandelier Light Fixture

Product Specifications

• Item Number : 6248246
• Parts Included :
  • (C) Single bar (1)
  • (D) Green ground screw (1)
  • (E) Canopy (1)
  • (F) Collar ring (1)
  • (G) Collar loop (1)
  • (H) Quick link (2)
  • (I) Chain (1)
  • (J) Loop (1)
  • (K) Stem (1)
  • (L) Ball (1)
  • (M) Arm (19)
  • (N) Ceramic flower (76)
• Accessories Included:
  • (A) Wire connector (3)
  • (B) Mounting screw (2)
  • (N) Ceramic flower (1)

Product Usage Instructions

Assembly & Installation

1. Remove the fixture from the carton and ensure all parts and accessories are included.
2. Step A: Attach stem (K) to the top ball (L) and rotate arms (M) onto the ball.
3. Step B: Determine the correct hanging height, connect chain links using the quick link (H), and thread wires throughthe chain.
4. Step C: Mount the fixture to the outlet box, secure the canopy (E), and make wire connections according to colour codes.

Safety Precautions

• Always shut off the electricity before starting any work.
• Ensure proper wire connections and grounding as per instructions.
• Consult a licensed electrician if needed.

FAQ

• Q: Can I install the fixture myself without an electrician?
• A: While installation instructions are provided, it is recommended to have a licensed electrician perform the installation to ensure safety and proper setup.
• Q : What should I do if any parts are missing or damaged?
• A : If any parts are missing or damaged, please contact the place of purchase to order replacement parts using the exact wording from the illustration.

WARNING (To reduce the risk of fire, electric shock, or injury to persons)

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. When replacing a bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

FINISHED PRODUCT：

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED)
Before doing assembly and installation please prepare the needed tools as below picture

PARTS

PARTS TYPE & QTY INCLUDING

• (C) Single bar (1)
• (D) Green ground screw (1)
• (E) Canopy (1)
• (F) Collar ring (1)
• (G) Collar loop (1)
• (H) Quick link (2)
• (I) Chain (1)
• (J) Loop (1)
• (K) Stem (1)
• (L) Ball (1)
• (M) Arm (19)
• (N) Ceramic flower (76)

ACCESSORIES & QTY ENCLOSED:

• (A) Wire connector (3)
• (B) Mounting screw (2)
• (N) Ceramic flower (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation

• Step A1: Slip the stem (k) along wires then thread onto the nipple of the top ball (L) till snug, and rotate the arms (M) on the ball (L).
• Step A2 : Rotate the ceramic flower (N) on the arms (M).

• Step B1 : By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
• Step B2 :Attach the quick link (H) to connect the chain (I) and the loop(J) on the top of the stem (K).
• Step B3 : Carefully lace the wires through the chain (I)(every other link)and stop just before you reach the top of the chain (I). Gently pull the wires till snug.

Turn off power
Before you start to make an installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF” position.
Make installation

• Step C1 : Remove the threaded ring (F) from the collar loop(G). Attach the single bar (C) to outlet box with mounting screws (B). The side of the single bar marked “GND” must face out, Unscrew the collar ring (H) from the collar loop.
• Step C2 : Pass canopy (E) over the mounted collar loop (G) then secure with threaded ring (F) to test the height . Unscrew the threaded ring (F) from the collar loop (G) and remove the canopy (E)

Note: The canopy (E) should be snug against the ceiling and the collar loop (F) should be screwed enough threads (no less than 6 threads )over the threaded nipple for more secure hanging. If not, adjust the height of the nipple and collar loop (G) until the desired height is reached. Remove the threaded ring (F) and canopy (E) and place to the side.

• Step C3: Slip the threaded ring(F) over the chain(I), then do the same with the canopy(E).
• Step C4: Open the quick link(H)， and attach the quick link (H) to connect the loop (G). Close the quick link(H) Pass the wires through the screw collar loop(G) to the top of the nipple and gently pull till snug.
• Step C5: If needed, cut off the wire length of the fixture. At this point, the remaining wire length measured from the top single bar(C) is at least 6″. StepC6: Make wire connections Connect wires as below wires connecting shown.

TAKE NOTE OF THE WIRE  COLOR OF FIXTURE, NEVER CONNECT WIRE TO GROUND WIRE

Connect ground wire according to the below chart

Connect wires according to the below chart

Note: When parallel wires (SPT | & SPT II) are used. The neutral wire is square-shaped or ridged and the other wire will be round in shape or smooth (see Illus.

Twist the plastic wire connector until wires are tightly joined together, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step C7: Raise canopy (E) to ceiling and secure canopy (E) in place by tightening threaded ring (F) onto collar loop (G).
• Step C8: Install bulbs (not included) (Please do not exceed the maximum capacity recommended on the socket.)

Check everything is already installed properly, and then you can turn on the light. Enjoy!
CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

References

• The domain name tape.be is for sale | Dan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>