Secukey HFD3-WIFI Access Controller/ Reader User Manual

June 1, 2024
Secukey

Securely HFD3-WIFI Access Controller/Reader

INTRODUCTION

  1. The device is a single-door multifunction standalone access controller or a
  2. Wiegand output reader. It uses Atmel MCU assuring stable performance.
  3. The operation is very user-friendly, and the low-power circuit makes it a long service life.
  4. The device can be made with Bluetooth function or with a WIFI function.

Card/ PIN device:
It supports 10,000 users (9988 common + 2 panic + 10 visitor)

Card/ PIN/Fingerprint device:

Three user capacities are available:

  1. It supports 10,000 card/PIN users + 100 fingerprint users
  2. It supports 10,000 card/PIN users + 500 fingerprint users
  3. It supports 10,000 card/PIN users + 880 fingerprint users
Features
  • OLED display, touch keypad
  • Wide: ABS, Slim: metal or ABS optional
  • Waterproof, conforms to IP66
  • One relay
  • PIN length: 4~6 digits
  • EM card, EM+ Mifare card optional
  • EM card: Wiegand 26~44 bits input & output
  • Mifare card: Wiegand 26~44bits, 56bits, 58bits input & output
  • Can be used as a Wiegand reader with LED & buzzer output
  • Card block enrollment
  • Tri-color LED status display
  • Integrated alarm & buzzer output
  • Pulse mode, Toggle mode
  • User data can be transferred
  • 2 devices can be interlocked for 2 doors
  • Built-in light-dependent resistor (LDR) for anti-tamper
  • The backlit keypad can set automatic OFF after 20 seconds

Overview

Specifications

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(2\)

Wiring

Wiring (for Wide device)

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(3\)

Wiring (for Slim device)

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(4\)

Carton Inventory

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(5\)

INSTALLATION

  • Remove the back cover from the unit
  • Drill 2 holes(A, C) on the wall for the screws and one hole for the cable
  • Knock the supplied rubber bungs to the screw holes (A, C)
  • Fix the back cover firmly on the wall with 4 flat-head screws
  • Thread the cable through the cable hole(B)
  • Attach the unit to the back coverSecukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(6\)

CONNECTION DIAGRAM

Standalone Mode
The device can work as a Standalone Access Control for a single door. (Factory default mode)

Connection Diagram (for Wide device)

Common Power Supply

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(7\)

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the keypad might be damaged. (1N4004 is included in the packing)

Access Control Power Supply

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(8\)

Connection Diagram (for Slim device)

Common Power Supply

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(9\)

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the keypad might be damaged. (1N4004 is included in the packing)

Access Control Power Supply

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(10\)

Controller Mode

The device can work as a Controller, connected to the external Wiegand reader. (Factory default mode)

Connection Diagram (for Wide device)

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(11\)

Connection Diagram (for Slim device)

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(12\)

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the reader might be damaged. (1N4004 is included in the packing)

WIEGAND READER MODE

The device can work as a Standard Wiegand Reader, connected to the third-party Controller

Connection Diagram

Notes:

  • When set into Wiegand Reader mode, nearly all settings in Controller Mode will become invalid, and Brown & Yellow wires will be redefined as below:
    • Brown wire: Green LED light control
    • Yellow wire: Buzzer control
  • If you need to connect Brown/Yellow wires:
    When the input voltage for LED is low, the LED will turn Green; and when the input voltage for Buzzer is low, it will sound.

PROGRAMMING

Keys & Functions
0-9: Enter value, menu number

  • Ok means confirm

    means down to select

  • Means doorbell

  • M means menu

    • Short press * means back to the previous menu
    • Long press * means back to the main interface

System Menu

  • Please input * (Master Code) # to enter the system menu. (Factory default master code is 123456)
  • User ID number:
    • The Common Card/PIN User ID: 1~9988
    • Panic User ID: 9989~9990
    • Visitor User ID: 9991~10000
    • Fingerprint User ID (Only apply to card/PIN/ Fingerprint device)
    • 10001~10100 or 10001~10500 or 10001~10880
  • PIN: Can be any 4~6 digits
  • Proximity Card: 125KHz EM card or 13.56MHz Mifare card

Change Admin
Press ‘1’ to enter Change Admin.

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(17\)

User Setting

  • Press ‘2’ to enter User Setting.
  • Press to select and long press # to confirm.

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(19\) Secukey-HFD3-WIFI-Access-Controller-Reader-Fig-
\(20\)

Door Setting

  • Press ‘3’ to enter the Door Setting.
  • Press to select and long press # to confirm.

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(21\) Secukey-HFD3-WIFI-Access-Controller-Reader-Fig-
\(22\)Secukey-HFD3-WIFI-Access-Controller-
Reader-Fig- \(23\)

Other Setting

  • Press ‘4’ to enter the Other Setting.
  • Press to select and long press # to confirm.

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(24\) Secukey-HFD3-WIFI-Access-Controller-Reader-Fig-
\(25\)

ADVANCED APPLICATION

User Information Transfer (Valid for Card/ PIN device)
The device supports the User Information Transfer function, and the enrolled user (cards, PINs) can be transferred from one (let’s name it Master Unit) to another (let’s name it Accept Unit).

Connection Diagram:

Remarks:

  • The Master units and Accept units must be the same series of devices.
  • The Master Code of the Master Unit and the Accept Unit must be set to the same.
  • Program the transfer operation on the Master Unit only.
  • If the Accept Unit is already with the users enrolled, it will be covered after transferring.
  • For a full 10000 users enrolled, the transfer takes about 5 minutes.

Set Transferring on Master Unit: Menu 4 Other Setting– 6 Copy User

Interlock
The device supports the Interlock Function. It is of two Devices for two doors and is mainly used for banks, prisons, and other places where a higher level of security is required.

Connection Diagram:

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(27\)

Remarks:
The Door Contact must be installed and connected as in the diagram. Let’s name the two Devices “A “and “B” for two doors “1” and “2”

  • Step 1:
    Enrol the users on Device A, then transfer the users’ information to Device B by the ‘User Information Transfer’ function (Page 111)

  • Step 2:
    Set both of the two devices (A and B) to Interlock function Menu 3 Door Setting — 6 Interlock

If enable interlock, when and only door 2 is closed, the user can read the valid fingerprint/card or input PIN on Reader A, and door 1 will open; then when and only door 1 is closed, read the valid fingerprint/card or input PIN on Reader B, door 2 will open.

SOUND AND LIGHT INDICATION

Secukey-HFD3-WIFI-Access-Controller-Reader-Fig- \(28\)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals