NIGHT OWL BWNIP4 Series Wire Free Camera User Guide

BWNIP4 Series Wire Free Camera

“`html

Specifications:

• Camera Type: Battery Wi-Fi Camera
• Power Source: Rechargeable Batteries
• Connectivity: Wi-Fi
• Additional Features: PIR Motion Detection, microSD Card
  Slot

Product Usage Instructions:

1. Installing the Batteries:

Press the button on the camera to release the battery cartridge.
Insert the rechargeable batteries (2 per camera). Replace the
cartridge and connect the USB cable to the port under the rubber
piece.

2. Charging the Camera(s):

Charge the camera(s) for at least 3 hours by connecting the USB
cable to the camera and a USB power supply. Make sure the batteries
are installed for charging.

3. Connecting to Wi-Fi Router:

Open the Night Owl Protect App, tap on Add New, and follow
on-screen instructions. You can use QR Code, Network Discovery, or
Manual setup by UID for connection.

4. Camera Installation:

1. Use the holes in the back of each camera to mark screw
   positions on the mounting surface.

2. Drill into the surface using a bit slightly smaller than the
   screw anchors.

3. Insert screw anchors, align camera base holes with anchors,
   insert screws, and tighten to secure the camera.

FAQ:

Q: Can I use third-party batteries with the camera?

A: Using third-party batteries may damage the camera and void
your warranty. Compatible batteries can be purchased at
NightOwlSP.com.

Q: How long should I charge the camera(s) for initial

setup?

A: It is recommended to charge the camera(s) for at least 3
hours for initial setup. Keep the camera plugged in during this
time.

Q: What should I do if my camera is not in pairing mode?

A: Press and hold the reset button on the camera for 10 seconds
or until you hear “Camera is in Pairing Mode”. Keep your camera
plugged in for up to 3 hours to fully charge.

“`

Quick Setup Guide
Let’s get started

GND

What’s Included Battery Wi-Fi Cameras

Battery Wi-Fi Camera(s)

Rechargeable Batteries (Includes 2 per Camera)

Mounting Hardware Kit

(1) USB-C Charging Cable

NOTE: If mounting the camera, you will need a screwdriver or drill (not included).

2

Battery Wi-Fi Camera Details

Lens

LED

MIcrophone

PIR

USB-C Port Cover
Housing Release Button

microSD Card

USB-C Port Battery

Camera Bottom (With Cover)

Camera Bottom (Without Cover)

3

Download the Night Owl App
If you are a first-time user, go ahead and download the Night Owl app. Quickly create an account and log in. Already have an account? Simply log in.
4

Initial Start-up Steps
1. Install the batteries. Press the button on the camera’s belly to release the battery cartridge and insert the batteries. Replace the cartridge and connect the USB cable to the port under the rubber piece.

Press Button

Insert Batteries

NOTE: Each camera requires 2 rechargeable batteries but can hold up to 4 batteries. Use of 3rd party batteries may damage the camera and void your warranty. Compatible batteries can be purchased at NightOwlSP.com
5

Initial Start-up Steps (Continued)
2. Charge the camera(s) for at least 3 hours. Lift the rubber piece on the camera’s belly and connect the USB cable to the camera and a USB power supply. Please ensure the batteries are installed or the camera(s) will not charge.
Placing the camera in Pairing Mode (if needed): If the camera is not in pairing mode, press the button on the camera’s belly to release the battery cartridge. Press and hold the reset button for 10 seconds or until the camera says, “Camera is in Pairing Mode.”
NOTE: Keep your camera plugged in for up to 3 hours to fully charge.
6

Connecting to a Wi-Fi Router
Adding Your Camera
1. Open the Night Owl Protect App. 2. Tap on “Add New” or “+” 3. Follow the on-screen instructions to complete the
setup process.
For iOS Tap “Add New.”

For Android Tap “+”

iOS

Android

7

Connecting to a Wi-Fi Router (Continued)
Setup Using: QR Code (Recommended), Network Discovery, Manual by UID.
Model: BWNIP-4TA-BS S/N: XXXX XXXX XXXX
Once the QR Code is captured the App leads you through the rest of the process.
8

Doorbell Installation (Continued)
If setup is completed using Network Discovery or Manual setup by UID once your device is added to the network you will need to select the category of the device to proceed.
Select “Standalone camera” from the device list
NOTE: The Router’s security protocol MUST be set to WPA/WPA2 (strong security).
9

Add Your Camera
To begin viewing your camera, add it to the Night Owl app or to a compatible recorder. For more detailed setup steps, please scan the QR code below.
10

Camera Installation
1. Use the holes in the back of each camera as a template to mark the screw positions on the surface where you plan to mount the camera.
2. Using a drill bit slightly smaller than the included screw anchors, drill into the mounting surface using the guide marks.
3. Insert the screw anchors. Line up the camera base holes with the screw anchors, insert the screws through the base and tighten to secure the camera in place.
11

Need Help?
For more help, please follow the steps below to access your Series support page:
1. Please visit: Support.NightOwlSP.com
2. Enter BWNIP4 into the Search bar or scan the QR Code
FCC RADIATION NORM FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Compliance Statement These limits are designed to provide reasonable protection against frequency interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed or used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in television reception, which can be determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and the receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. CAUTION! The Federal Communications Commission warns the user that changes or modifications to the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment should be installed and operated with a minimum distance of 8 inches between the radiator and your body.
QSG-BWNIP4 1-240819

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>