Penguin PA1010 Vikos 10×10 Aluminum Free Standing Pergola Instruction Manual

Penguin PA1010 Vikos 10×10 Aluminum Free Standing Pergola

Vikos 10×10 Pergola autoportante en aluminium Vikos 10×10 Aluminum Free Standing Pergola
sku:PA1010

DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED
FOR FUTURE REFERENCE,
TAKE PICTURES OF ALL SIX SIDES OF EACH OF THE BOXES UPON RECEIPT.
PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS
10ft x 10ft / 3m x 3m Pergola

Instruction Manual
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

Consult with your local governing authority / local municipal codes regarding installation of temporary structures before purchase or assembly. Some jurisdictions may require permits for, or otherwise regulate, installation and use.

For assistance with assembly, installation, parts, or customer service, contact Gazebo Penguin Customer Service Department at the numbers listed below (English & French, Mon-Fri 8:00 AM to 4:00 PM EST):

Montreal: 514-276-3485
Elsewhere in Canada and the US: 1-800-737-7174

WARNING:

• For outdoor use.
• Snow should be regularly cleared from the roof and not allowed to accumulate.
• Retain your proof of purchase for warranty purposes. Also keep the original boxes until the installation is complete and correct.
• The unit may take more than 4 hours and 3 people are required for this assembly.

PRIOR TO ASSEMBLY

• Please don’t destroy boxes until completely assembled.
• The foundation must be level, flat, and solid, such as concrete or asphalt.
• Keep away from overhead utility lines, tree branches, and other structures.
• Check for underground pipes or wires if digging or drilling is required.
• Do not install near roof lines or other structures that could shed snow, ice, or excessive rain run-off onto the roof top.
• Assemble the structure as close to its final location as possible.
• It is recommended to wear safety gloves, safety glasses, and hard hats for installation.
• Do not hang from, climb on, or stand on the structure or roof.
• Before assembly, read instructions and check that all parts are present in the boxes. If any parts are missing, refer to warranty information.
• A 6ft (1.8m) stepladder, Phillips screwdriver, tape measure, level, mallet, and a tarp to place parts on will be required for assembly (not included).
• Remove top protective film from roof panels prior to assembly; DO NOT remove bottom protective film until ready to insert roof panels, so as to identify which side is on top.

ANCHORING INSTRUCTIONS:

• Proper anchoring of the frame to the base and the wall is required for safety.
• Any structure not anchored securely has the potential to fly away during high wind causing damage and safety hazard.
• How the item is anchored, and the hardware and tools required, will vary based upon the set up location and are not provided.
• Please check with your local hardware store if for the appropriate anchors for your surface.
• Do not anchor to pavers / pavement slabs because they are not a solid foundation.
• Periodically check the anchors to ensure they remain secure

CARE AND MAINTENANCE:

In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly.
Please have the parts list and part numbers on hand when ordering or requesting replacement parts.

ROOF PANELS:

• Gently clean with an environmentally-friendly soap solution and water using a sponge or washcloth.
• Do not use abrasive materials, wire brushes, chemicals, harsh cleaners, or bleach.
• Rinse using a garden hose and air dry. If removed, ensure thoroughly dry prior to storage.
• Do not use pressure washer.

STRUCTURE

• Gently clean with an environmentally-friendly soap solution and water using a sponge or washcloth.
• Do not use abrasive materials, wire brushes, chemicals, harsh cleaners, or bleach.
• Rinse using a garden hose and air dry.
• Do not use pressure washer.
• If there are nicks,chips,and/or scratches see the part # of the paint in the parts list to obtain a matching touch-up paint.

1.  Connect the Base Plate (J) and Corner Post (A) together and secure with Bolts (OO). See Figure 2.

2. Slide the ends of the Front Lintel (D/F) into the groove in the Corner Post (A) and tighten
   Diagram of internal structure the bolts in the Front Lintel (D/F) with the Allen Wrench (MM). See Figure 2.

3. Slide one end of the Lintel (B/C) into the built-in guide of the Corner Post (A) and tighten it by Allen Wrench (MM). See Figure 3.

4. Connect the Middle Lintel (E) to the Front Lintel (D) on one end and the other end to the Rear Lintel (F), securing them together with Bolts (AA) and Washers (HH). See Figure 4.

5. Connect the Cap Liner (I/I1) to the Corner Post (A) securing them with Bolts (BB). See Figure 5.1-5.3

6. Attach the Rocker Connector (N1/N2) to the LIntels (B/C/E) using Bolts (AA) and Washers (HH). See Figure 6.

7. Insert one side of the two Connecting Rods (H1/H2) into the Spinner (M) and the other side into the Spinner (M), then attach the Spinner (M) to the Rear Lintel (F) and secure it with the Bolts
   (AA) and Washers (HH). Finally the other end of the Connecting Rods (H1/H2) is attached to the Lintels (B/C/E) using Bolts (CC), Washers (GG/HH) and Nuts (FF).See Figure 7.1- 7.3.

8. Connect the Louver (G) to the Lintels (B/C/E) and secure with the Bolts (EE). See Figure 8.1-8.3. 8.2. Assemble the other Louvers (G) in the direction of the arrows and secure them with Bolts (EE). See Figure 8.4.

9. Connect the Cover Plate (G1) to the Lintels (B/C/E), securing it with Bolts (SS) and Washers (HH). See Figure 9.1-9.3.

10. Secure the Pergola onto the deck or something by using Screws (DD)、Washers (HH) and Plastic Plugs (Il) to make sure the steadiness of the item.See Figure 10.1.

11. Hang the Crank (H3) on the Spinners (M) and turn to open or close the louvers.See Figure 10.2.

Warm Tips
Please close the louvers when it rains.

Note: After the rain, please open the louvers slowly to prevent the residual rain water from splashing.

WARRANTY

WARRANTY
Carefully inspect the contents of the package for missing or damaged components. If any parts are missing or damaged, do not return the product to the place of purchase; instead, contact the Gazebo Penguin Customer Experience Department

Montreal: 514-276-5643
Elsewhere in Canada and the United States : 1-800-737-7174
[email protected]

This product has been designed and manufactured to meet the highest standards of quality and durability. Subject to the “Warranty Conditions” and “Warranty Limitations” sections below, it is warranted against defects in material or workmanship for:

1 YEAR ON MANUFACTURING DEFECTS

In the event that the product is damaged or the warranty period has expired, please contact the Penguin Gazebo Customer Experience Department for a complete list of replacement parts and prices.

WARRANTY LIMITATIONS AND EXCLUSIONS

1. This product is not warranted against damage caused by wind, falling objects, fire, animals, vegetation, vandalism and extreme weather conditions.

2. Collapses of shelters caused by snow, ice and wind accumulation

3. The roof must be kept free of snow and ice accumulation at all times.

4. Any damage that may be caused by snow and ice accumulation is not covered by the warranty.
   Snow and ice must be removed from the roof, from right to left, in five feet (5) sections at a time.

5. Removal of snow and ice from the product from the inside may damage the product and may cause serious injury to the person(s) involved in the removal.

6. It is strongly recommended that the product not be placed adjacent to buildings or trees as snow or ice may slide off the roof. In the event that the product is placed adjacent to a building or tree, additional precautions must be taken to ensure that there is no accumulation of snow or ice that could cause excessive weight to the product.

7. The product is warranted only if installed in accordance with Gazebo Penguin’s written instructions included with the product.

8. Leaks due to heavy rainfall may occur. Please refer to the instruction manual for window positions and information on how to drain water.

9. The product is not guaranteed if it has been anchored improperly.

10. We reserve the right to replace or repair any defective product or part at our sole discretion.

11. No modifications or additions to the product are permitted. This will void your warranty.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>