Penguin 12’x14’ GAZEBO Installation Guide
- June 7, 2024
- Penguin
Table of Contents
12’x14’ GAZEBO
43224-22 BROWN 43224-32 SLATE
12’x14′ GAZEBO ASSEMBLY INSTRUCTIONS
DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED
PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS
Assembly With Two Or More Adults Recommended
Base Dimensions 10′ 11″ x 13′ 4″ Largest Dimensions 11′ 11″ x 14′
Overall Height 108.5”
APPROX.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
1
DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT
OF EACH BOX AGAINST THE LIST OF PARTS
12ft x 14ft / 3.65m x 4.26m GAZEBO Instruction Manual
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
Consult with your local governing authority / local municipal codes regarding
installation of temporary structures before purchase or assembly. Some
jurisdictions may require permits for, or otherwise regulate, installation and
use.
For assistance with assembly, installation, parts, or customer service, contact Gazebo Penguin Customer
Service Department at the numbers listed below (English & French, Mon-Fri 8:00 AM to 4:00 PM EST):
Montreal: 514-276-3485
Elsewhere in Canada and the US: 1-800-737-7174
WARNING: For outdoor use. Snow should be regularly cleared from the roof and
not allowed to accumulate. Retain your proof of purchase for warranty
purposes. Also keep the original boxes until the installation is complete and
correct. The unit may take more than 4 hours and 3 people are required for
this assembly.
PRIOR TO ASSEMBLY: Please don’t destroy boxes until completely assembled. The
foundation must be level, flat, and solid, such as concrete or asphalt. Keep
away from overhead utility lines, tree branches, and other structures. Check
for underground pipes or wires if digging or drilling is required. Do not
install near roof lines or other structures that could shed snow, ice, or
excessive rain run-off onto the roof top. Assemble the structure as close to
its final location as possible. It is recommended to wear safety gloves,
safety glasses, and hard hats for installation. Do not hang from, climb on, or
stand on the structure or roof. Before assembly, read instructions and check
that all parts are present in the boxes. If any parts are missing, refer to
warranty information. A 6ft (1.8m) stepladder, Phillips screwdriver, tape
measure, level, mallet, and a tarp to place parts on will be required for
assembly (not included). Remove top protective film from roof panels prior to
assembly; DO NOT remove bottom protective film until ready to insert roof
panels, so as to identify which side is on top.
ANCHORING INSTRUCTIONS: Proper anchoring of the frame to the base and the wall
is required for safety. Any structure not anchored securely has the potential
to fly away during high wind causing damage and safety hazard. How the item is
anchored, and the hardware and tools required, will vary based upon the set-up
location and are not provided. Please check with your local hardware store if
for the appropriate anchors for your surface. Do not anchor to pavers /
pavement slabs because they are not a solid foundation. Periodically check the
anchors to ensure they remain secure
CARE AND MAINTENANCE: In case of a defective or damaged part, or for any other
questions concerning the product, please contact the manufacturer directly.
Please have the parts list and part numbers on hand when ordering or
requesting replacement parts.
ROOF PANELS: Gently clean with an environmentally-friendly soap solution and
water using a sponge or washcloth. Do not use abrasive materials, wire
brushes, chemicals, harsh cleaners, or bleach. Rinse using a garden hose and
air dry. If removed, ensure thoroughly dry prior to storage. Do not use
pressure washer.
STRUCTURE: Gently clean with an environmentally-friendly soap solution and
water using a sponge or washcloth. Do not use abrasive materials, wire
brushes, chemicals, harsh cleaners, or bleach. Rinse using a garden hose and
air dry. Do not use pressure washer. If there are nicks, chips, and/or
scratches see the part # of the paint in the parts list to obtain a matching
touch-up paint.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
2
MAINTENANCE NOTES
1. In case of a defective or damaged part, or for any other questions
concerning the product, please contact the manufacturer directly.
2. Please have the parts list and part numbers on hand when ordering or
requesting replacement parts. 3. The product should not be installed adjacent
to trees or a sloped roof. Snow and ice may slide onto the roof and cause it
to collapse. 4. While the product is designed to stay assembled year long, the
roof must be kept free of accumulation of snow.
ONE YEAR LIMITED WARRANTY
This product has been designed and manufactured to meet the highest standards
of quality and durability. Subject to the Conditions for Exercising the
Warranty and the Limitations on the Warranty set forth below, it is warranted
to be free of material and manufacturing defects for a period of one year from
the date of purchase. Missing and damage due to transportation is not covered
by the manufacture warranty. Should the product become damaged, or the
warranty period has expired, please contact Gazebo Penguin Customer Service
Department for a complete schedule of replacement parts and prices.
CONDITIONS FOR EXERCISING THE WARRANTY
The warranty only applies to the original purchaser with the bill. In order to
properly exercise your warranty, please comply with the following:
Carefully inspect the contents of the carton for missing or damaged
components. Should you discover damaged or missing parts, do not return the
product to the place of purchase, but contact Gazebo Penguin Customer Service
Department at the numbers listed below: Montreal:
514-276-3485 Elsewhere:
1-800-737-7174 You can also find a
claim form to fill out online: https://abrispenguin.com/assemblyinstructions/
NOTE: Damages/missing parts must be reported within 30 days of delivery. If
claimed after your request might be rejected.
LIMITATIONS ON THE WARRANTY
1. The product is not warranted against damages due to vandalism, abuse,
falling or thrown objects, or accumulation of snow.
2. The product is not warranted against damages due to extreme weather
conditions, such as thunderstorms, hail, strong wind or snow storms, or any
other acts of God.
3. Leaking due to heavy rain may happen, please refer to the instruction
manual for window positions and information on how to evacuate the water.
4. The product is only warranted in the event it is installed in accordance
with the Gazebo Penguin’s written instructions enclosed with the product.
5. The product is not warranted in the event it has been improperly anchored.
6. We reserve the right to replace or repair any defective product or parts at
our discretion. 7. No change to the unit is allowed. This will void your
warranty.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
3
Before You Assemble the Gazebo
PLEASE DON’T DESTROY BOXES UNTIL COMPLETELY ASSEMBLED
Please verify the content of each box against the list of parts. It is
important that this gazebo be anchored on a solid base with the provided
screws.
Otherwise, please ensure that you use anchors sufficient for your surface. The
gazebo should not be installed adjacent to trees or a sloped roof. Snow and
ice may slide
onto the gazebo and cause it to collapse.
Tools required (Not Provided) 6ft (1.8m) Stepladder Robinson #2 Screwdriver Mallet Safety Gloves & Glasses Shim
Tarp or protective material for placing parts on during assembly
Tape Measure Leveling
Step 1:
1. Assemble Beams “A” and “B” using Center Plate “F”, by sliding it inside
the beams and securely tighten with 10 Bolts “Pp”. Repeat with Beams “C” and
“D”, also using Center Plate “F”.
2. Lay out the assembled Beams in a rectangle and join at each corner with a
Corner Plate “E”,
by sliding it inside the beams and tighten it with 4 Bolts “Pp” tightly and
hand fasten remaining 4 Bolts in pink. see image on pg. 5
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
4
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
5
Step 2: For each leg “G”, attach foot plate “H” using 3 bolts “Pp”.
Step 3: 1. Unscrew 4 Pp Bolts as shown below, have someone lift the Beam
assembly and attach each Leg “G” into a Corner, again securing each using 4
Bolts “Pp”. 2. Repeat until all four Legs are in place
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
6
Step 4:
1. Install Middle Cover “J” at each of the 4 beam junctions, using 4 Screws
“Qq” each. 2. Install Corner Cover “I” at each of the corners, using 4 Screws
“Qq” each.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
7
Step 5:
1. Attach Mounting Brackets “O” to Rafters “M”, and Mounting Brackets “P” to
Rafters “N” and “N-2″. Use threaded hole about 8½” & 5″ from end of rafter.
2. Lift Central Hub “L” to a height of about 110″ (2.79m) at the center of
the gazebo. (Caution: this part may be heavy, use support as needed)
3. Attach one end of Rafter “M” to the hub using 1 Bolt “Pp”. Attach other
end with Mounting Bracket to the corner of the beam assembly with 2 Bolts
“Pp”. Use the set of holes closest to the inside. Repeat with remaining “M”
Rafters.
4. Similarly, attach one end of Rafter “N” to the hub using 1 Bolt “Pp”.
Attach other end with mounting bracket to the beam assembly with 2 Screws
“Qq”. Use the set of holes closest to the inside. Repeat with remaining “N”
and “N-2” Rafters.
Pp
Pp
Pp
Step 6: 1. Once all rafters are in place, install Top Cap “K” over Central Hub
“L”. Use flat Washers and Acorn Nuts “Vv” to secure tightly.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
8
Step 7: Install the flashings “Q”, “R”, “S”, and “S-2” onto the beam assembly,
using screws “Qq” on the inside. The notched end of a flashing will always go
in a corner of the gazebo.
Step 8: Install the curtain rails “T” and “U” on the inside of the beam
assembly using bolts “Pp”.
Pp
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
9
Step 9: Slide the indicated polycarbonate panels into the spaces between the
rafters, using the top groove of each rafter. Ensure the side meant to face
the sun is on the outside. Use a rubber hammer to carefully tap each panel
into the grooves.
Step 10: Insert the middle roof joints in between the rafters and slide them
up under the polycarbonate panels. Tap lightly to ensure the panel is fully in
the slot. Seen from above, most of the joint as well as the drain holes should
be beneath the roof panels. To adjust the middle joints to line up : once all
polycarbonate roof panels are in place, use a small piece of wood and hammer,
then tap down on the middle of the joint bringing it down and holding at the
same time the joint and top polycarbonate. Do not tap too hard.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
10
Step 11:
1. Slide the remaining polycarbonate roof panels in the lower groove of the
rafters and into the lower slot of the roof joints. Tap to make sure panels
fit securely and do not extend past the ends of the rafters.
Step 12:
1. Starting from any end, install all edgings, with end caps “Gg” or “Hh” at
each junction or corner respectively. Use bolts “Pp” to secure.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
11
Step 13:
1. Install the upper
crossbars on the
interior of the roof
using bolts “Pp”, following the
Pp
shaped ends
and letters. Do
not tighten bolts
immediately;
install loose and
tighten once all
Pp
crossbars are
in place.
2. Repeat this
step with the
lower
crossbars.
Pp
Step 14:
1. Secure each foot plate into the ground using screws “Rr” and Washers “Tt”.
2. Use lag shields (Ss) if needed for harder surfaces.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
12
Step 15:
1. Install the Screen Curtains “Ww” in the interior groove of the Curtain
Rails, using the provided hooks. Install the Privacy Curtains “Xx” in the
exterior groove of the rails. Once the hooks are in, use Curtain Rail Caps
“Uu” to close ends of curtain rails.
Note that both curtains are packaged and ordered in sets of 2 panels, each set
covering half the gazebo.
IMPORTANT NOTES: Make sure all screws and bolts are tight. If conditions are
windy, you may have to add cable guides at the corners.
Ww/Xx Ww/Xx
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
13
PACKED IN BOX
QTY
PACKED IN BOX
QTY
43224 BROWN (see page 18 for Slate parts)
PART
DIAGRAM
PART
(11-626-22)
65 ½”
TOP LEFT BEAM
3
2
A
(11-627-22)
65 ½” TOP RIGHT BEAM
B
3 2
(11-662-22)
78 ¼”
TOP LEFT BEAM
3
2
C
(11-663-22)
78 ¼”
TOP RIGHT
BEAM
3 2
D
(11-628-22) CORNER PLATE 3 4
E
(11-629-22) CENTER PLATE
F
3 4
(11-630-22) 81 ½” LEG G
3 4
(11-631-22) FOOT PLATE
H
3 4
(11-632-22) CORNER COVER 3 4
I
(11-633-22) MIDDLE COVER
J
3 4
(11-665-22)
60″
CENTRAL HUB L
(11-731-22)
92 5/8″ ROOF RAFTER
M
(11-708-22)
73 ¾”
ROOF RAFTER N
2 1 2 4 2 6
(11-637-22)
60 3/8″
ROOF RAFTER
N-2
2 2
(12-030-22)
RAFTER M
MOUNTING
2 4
BRACKET
O
(12-031-22)
RAFTER N
MOUNTING
2 8
BRACKET
P
(11-638-22)
55 ¼”
RIGHT
2 4
FLASHING
Q
(11-639-22)
55 ¼”
LEFT FLASHING
2
4
R
(11-640-22)
25 3/8″
CENTER
2 2
FLASHING
S
(11-709-22)
51″
CENTER
2 2
FLASHING
S-2
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
DIAGRAM 14
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
DIAGRAM
PART
(11-664-22)
63″
TOP CAP
K
2 1
(11-641-22)
60 ½”
CURTAIN RAIL,
12′ SIDE U
2 4
(11-674-22)
31″x38″
LEFT UPPER 1 2 PANEL, 12′ SIDE
V
(11-711-22)
31″x38″
RIGHT UPPER 1 2 PANEL, 12′ SIDE
V-2
(11-734-22)
37″x25 ½”
MIDDLE UPPER ROOF PANEL W
1 4
(11-675-22)
37 ½”x30 ½”
RIGHT UPPER 1 2 PANEL, 14′ SIDE
X
(11-712-22)
37 ½”x30 ½”
LEFT UPPER 1 2 PANEL, 14′ SIDE
X-2
(11-676-22)
38 ½”
LEFT MID ROOF
JOINT, 12′ SIDE Y
2 2
(11-666-22)
73 ¼”
CURTAIN
2 4
RAIL, 14′ SIDE
T
(11-678-22)
32 ¼”x72″
LEFT LOWER
PANEL, 12′
1 2
SIDE
Bb
(11-721-22)
39″x57 ½”
LEFT LOWER PANEL, 14′
1 2
SIDE
Bb-2
(11-679-22)
32 ¼”x72″
RIGHT
LOWER
1 2
PANEL, 12′
SIDE
Cc
(11-722-22)
39″x57 ½”
RIGHT
LOWER
1 2
PANEL, 14′
SIDE
Cc-2
(11-680-22)
72 5/8″
LEFT EDGING, 2 2
12′ SIDE
Dd
(11-715-22)
72 5/8″
RIGHT EDGING, 12′
2 2
SIDE
Dd-2
(11-652-22)
26 ¾”
CENTER
2 4
EDGING
Ee
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
DIAGRAM 15
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
(11-713-22)
38 ½”
RIGHT MID ROOF JOINT
2
2
12′ SIDE
Y-2
(11-647-22)
25 ½”
CENTER MIDDLE
2 4
ROOF JOINT
Z
(11-677-22)
31″
RIGHT MID
ROOF
2 2
JOINT, 14′
SIDE
Aa
(11-714-22)
31″
LEFT MID
ROOF
2 2
JOINT, 14′
SIDE
Aa-2
(11-682-22)
43 ¼”
LEFT LOWER CROSSBAR,
2
2
14′ SIDE
Ii
(11-717-22)
43 ¼”
RIGHT
LOWER
2 2
CROSSBAR,
14′ SIDE
Ii-2
(11-657-22)
26 ¾”
MIDDLE LOWER
2 4
CROSSBAR
Jj
DIAGRAM
PART
(11-653-22)
58 7/8″
RIGHT EDGING,
2
2
14′ SIDE
Ff
(11-651-22)
58 7/8″
LEFT EDGING,
2
2
14′ SIDE
Ff-2
(11-654-22)
RAFTER CAP
2
8
Gg
(11-655-22)
CORNER
END
2 4
BRACKET
Hh
(08-158-22)
BOLT
3 196
Pp
(08-156-22) SCREW 3 108 Qq
(08-167-22) SCREW 3 12 Rr
DIAGRAM
(M6x16mm) (M4x16mm) (M6x100mm)
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
16
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
(11-683-22)
53 ½”
RIGHT LOWER CROSSBAR, 12′ SIDE
Kk
2 2
(11-718-22)
53 ½”
LEFT LOWER CROSSBAR,
2
2
12′ SIDE
Kk-2
(11-685-22)
20 ½”
RIGHT UPPER CROSSBAR,
2
2
12′ SIDE
Ll
(11-720-22)
20 ½”
LEFT UPPER CROSSBAR,
2 2
12′ SIDE
Ll-2
(11-660-22)
26 ¾”
MIDDLE UPPER
2 4
CROSSBAR
Mm
(11-659-22)
17 ½”
LEFT UPPER CROSSBAR,
2 2
14′ SIDE
Nn
(11-661-22)
17 ½”
RIGHT UPPER CROSSBAR,
2
2
14′ SIDE
Nn-2
10 mm KEY 3 1
DIAGRAM
PART
DIAGRAM
(08-193-22)
PLASTIC PLUG
3 12
Ss
(08-187-22)
WASHER 3 16
Tt
(11-697-22)
CURTAIN RAIL CAP
3
8
Uu
(08-189-22)
ACORN NUT
3 4
Vv
(11-686) SCREEN/ 2 4
MOUSTIQUAIRE
Ww
(M6)
(11-687) PRIVACY CURTAIN
Xx
(11-698)
38″x25 ½”
MIDDLE LOWER
ROOF PANEL
Yy
2 Left 2
2 Right
2 Left 1
2 Right
(11-705) CURTAIN HOOKS
3 104
*NOT INCLUDED IN THE BOX
DESCRIPTION COLOUR
PART #
SPRAY PAINT
PAINT PEN
BROWN
11-726 18-184
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
17
43224 SLATE
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
DIAGRAM
PART
(11-626-32)
65 ½”
TOP LEFT BEAM
3
2
A
(11-627-32)
65 ½” TOP RIGHT BEAM
3 2
B
(11-662-32)
78 ¼”
TOP LEFT BEAM
3
2
C
(11-663-32)
78 ¼”
TOP RIGHT
3 2
BEAM
D
(11-628-32) CORNER PLATE 3 4
E
(11-629-32) CENTER PLATE
F
3 4
(11-630-32)
81 ½”
LEG G
(11-631-32) FOOT PLATE
H
3 4 3 4
(11-632-32) CORNER COVER 3 4
I
(11-633-32) MIDDLE COVER
J
3 4
(11-665-32)
60″
CENTRAL HUB L
(11-731-32)
92 5/8″ ROOF RAFTER
M
(11-708-32)
73 ¾”
ROOF RAFTER N
2 1 2 4 2 6
(11-637-32)
60 3/8″
ROOF RAFTER
N-2
2 2
(12-030-32)
RAFTER M
MOUNTING
2 4
BRACKET
O
(12-031-32)
RAFTER N
MOUNTING
2 8
BRACKET
P
(11-638-32)
55 ¼”
RIGHT
2 4
FLASHING
Q
(11-639-32)
55 ¼”
LEFT FLASHING
2
4
R
(11-640-32)
25 3/8″
CENTER
2 2
FLASHING
S
(11-709-32)
51″
CENTER
2 2
FLASHING
S-2
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
DIAGRAM 18
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
DIAGRAM
PART
(11-664-32)
63″
TOP CAP
K
2 1
(11-641-32)
60 ½”
CURTAIN RAIL,
12′ SIDE U
2 4
(11-674-32)
31″x38″
LEFT UPPER 1 2 PANEL, 12′ SIDE
V
(11-711-32)
31″x38″
RIGHT UPPER 1 2 PANEL, 12′ SIDE
V-2
(11-734-32)
37″x25 ½”
MIDDLE UPPER ROOF PANEL W
1 4
(11-675-32)
37 ½”x30 ½”
RIGHT UPPER 1 2 PANEL, 14′ SIDE
X
(11-712-32)
37 ½”x30 ½”
LEFT UPPER 1 2 PANEL, 14′ SIDE
X-2
(11-676-32)
38 ½”
LEFT MID ROOF
JOINT, 12′ SIDE Y
2 2
(11-666-32)
73 ¼”
CURTAIN
2 4
RAIL, 14′ SIDE
T
(11-678-32)
32 ¼”x72″
LEFT LOWER
PANEL, 12′
1 2
SIDE
Bb
(11-721-32)
39″x57 ½”
LEFT LOWER PANEL, 14′
1 2
SIDE
Bb-2
(11-679-32)
32 ¼”x72″
RIGHT
LOWER
1 2
PANEL, 12′
SIDE
Cc
(11-722-32)
39″x57 ½”
RIGHT
LOWER
1 2
PANEL, 14′
SIDE
Cc-2
(11-680-32)
72 5/8″
LEFT EDGING, 2 2
12′ SIDE
Dd
(11-715-32)
72 5/8″
RIGHT EDGING, 12′
2 2
SIDE
Dd-2
(11-652-32)
26 ¾”
CENTER
2 4
EDGING
Ee
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
DIAGRAM 19
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
(11-713-32)
38 ½”
RIGHT MID ROOF JOINT
2
2
12′ SIDE
Y-2
(11-647-32)
25 ½”
CENTER MIDDLE
2 4
ROOF JOINT
Z
(11-677-32)
31″
RIGHT MID
ROOF
2 2
JOINT, 14′
SIDE
Aa
(11-714-32)
31″
LEFT MID
ROOF
2 2
JOINT, 14′
SIDE
Aa-2
(11-682-32)
43 ¼”
LEFT LOWER CROSSBAR,
2
2
14′ SIDE
Ii
(11-717-32)
43 ¼”
RIGHT
LOWER
2 2
CROSSBAR,
14′ SIDE
Ii-2
(11-657-32)
26 ¾”
MIDDLE LOWER
2 4
CROSSBAR
Jj
DIAGRAM
PART
(11-653-32)
58 7/8″
RIGHT EDGING,
2
2
14′ SIDE
Ff
(11-651-32)
58 7/8″
LEFT EDGING,
2
2
14′ SIDE
Ff-2
(11-654-32)
RAFTER CAP
2
8
Gg
(11-655-32)
CORNER
END
2 4
BRACKET
Hh
(08-158-32)
BOLT
3 196
Pp
(08-156-32) SCREW 3 108 Qq
(08-167-32) SCREW 3 12 Rr
DIAGRAM
(M6x16mm) (M4x16mm) (M6x100mm)
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
20
PACKED IN BOX
QTY
PACKED IN BOX
QTY
PART
(11-683-32)
53 ½”
RIGHT LOWER CROSSBAR, 12′ SIDE
Kk
2 2
(11-718-32)
53 ½”
LEFT LOWER CROSSBAR,
2
2
12′ SIDE
Kk-2
(11-685-32)
20 ½”
RIGHT UPPER CROSSBAR,
2
2
12′ SIDE
Ll
(11-720-32)
20 ½”
LEFT UPPER CROSSBAR,
2 2
12′ SIDE
Ll-2
(11-660-32)
26 ¾”
MIDDLE UPPER
2 4
CROSSBAR
Mm
(11-659-32)
17 ½”
LEFT UPPER CROSSBAR,
2 2
14′ SIDE
Nn
(11-661-32)
17 ½”
RIGHT UPPER CROSSBAR,
2
2
14′ SIDE
Nn-2
10 mm KEY 3 1
DIAGRAM
PART
DIAGRAM
(08-193-32) PLASTIC PLUG Ss
(08-187-32) WASHER
Tt (11-697-32) CURTAIN RAIL CAP
Uu (08-189-32)
ACORN NUT Vv
(11-686) SCREEN/M OUSTIQUA
IRE Ww
3 12
3 16
3 8
3 4
2 Left 2
2 Right
(11-687) PRIVACY CURTAIN
Xx
(11-698)
38″x25 ½”
MIDDLE LOWER
ROOF PANEL
Yy
2 Left 2
2 Right
1 4
(M6)
(11-705) CURTAIN HOOKS
3 104
*NOT INCLUDED IN THE BOX
DESCRIPTION COLOUR
PART #
SPRAY PAINT
PAINT PEN
SLATE
18-125 18-126
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
21
NOTE: The Dimensions Are Approximate.
ZZZ-204.43224.0210-21.GP.EN.doc
WEB VERSION
22
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>