SEA EAGLE BP12ACC Single Stage Electric Pump Owner’s Manual

June 16, 2024
SEA EAGLE

SEA-EAGLE-logo

SEA EAGLE BP12ACC Single Stage Electric Pump

Specifications

  • Maximum Pressure: Approximately 18 psi (1 bar)
  • Air Output: 120 L/min
  • Automatic Stop

Product Usage Instructions

1. Setup:

The BP12ACC Single Stage Electric Pump comes with the following components:

  • Storage bag with multiple compartments
  • Inflation hose with adapter

To set up the pump, follow these steps:

  1. Connect the power connector to a Minn Kota Power Center or similar battery box with a battery.
  2. Screw the hose onto the inflation port on the end of the pump.
  3. Use the access hole with a protective flap to attach the hose without taking the pump out of the bag.
  4. Ensure that the recessed valve is in the UP (valve closed) position.
  5. Insert the adapter into the valve and twist it to the right until the hooks lock it into place.
  6. Insert the power connector into a 12v accessory power outlet. In a vehicle, the 12v power circuit is protected by a fuse, usually rated at 10 to 20 amps.

2. Inflation:

To inflate your boat or SUP, follow these steps:

  1. Turn the dial on the pump until the pointer indicates the desired pressure. The pressure settings are listed on the pump or refer to your boat owner’s manual for the correct setting.
  2. Monitor the inflation process and avoid running the pump continuously for more than 20 minutes to prevent overheating and damage.
  3. If the pump stops working before inflation is complete, check if the fuse has tripped and replace it if necessary (see troubleshooting section).

3. Safety Precautions:

When using the BP12ACC Single Stage Electric Pump, follow these safety precautions:

  • Do not run the pump continuously for more than 20 minutes to avoid overheating and damage.
  • Allow the pump to cool for 20 minutes before restarting it.
  • Use the pump away from water and protect it from rain to avoid electrical short circuits.
  • Do not leave the pump running unattended.
  • Keep the pump out of reach of children.

Frequently Asked Questions (FAQ)

1. What is the warranty for the BP12ACC Single Stage Electric Pump?

The BP12ACC Single Stage Electric Pump comes with a 3-year warranty against manufacturing defects. For complete warranty details, please visit SeaEagle.com/Warranty.

2. What should I do if I receive a damaged item?

If you receive a damaged item, please call the shipping carrier to report the issue. Do not return the damaged merchandise until it has been inspected by the carrier. Sea Eagle will be notified by the carrier when they have completed their inspection, and if necessary, Sea Eagle will arrange for the repair or replacement of the damaged merchandise.

3. How can I contact Sea Eagle for support?

You can contact Sea Eagle by calling 1-800-748-8066. Their business hours are Monday to Friday from 9 AM to 5 PM, EST. They pride themselves on answering the phone and helping customers with any concerns, questions, or special ordering needs.

Sea Eagle Warranty

Sea Eagle products come standard with a 3-year warranty against manufacturing defects. Complete warranty details can be found at SeaEagle.com/Warranty. If you receive a damaged item, please call the shipping carrier to report the issue. Do not return damaged merchandise until it has been inspected by the carrier. Sea Eagle will be notified by the carrier when they have completed their inspection and if necessary, Sea Eagle will arrange for the repair or replacement of damaged merchandise.

Contact Us

Unlike many other companies today we pride ourselves on answering the phone and helping you with any concerns, questions or special ordering needs that you may have! Feel free to give us a call at 1-800-748-8066 and we will be happy to talk with you! Our business hours are Monday to Friday from 9 AM to 5 PM, EST.

BP12ACC Single Stage Electric Pump for Inflatable Boats and SUPs

The BP12ACC is powered by simply inserting the male electrical plug into a 12v DC auxiliary power outlet also known as a car cigarette lighter. A vehicle may come with several outlets, some in the rear passenger area or the cargo area. These outlets usually have a plastic cap tethered to them, and are usually labeled as being only for DC power. Auxiliary power outlets are built into Minn Kota Power Centers and other similar battery boxes.

  • Caution: Do not run the pump for more than 20 minutes continuously as this can cause overheating and damage.

  • Caution: Allow the pump to cool for 20 minutes before restarting it.

  • Warning! Use the pump away from the water and protect it from rain to avoid electrical short.

  • Warning! Do not leave running unattended.

  • Danger! Keep out of reach of children.

  • Specifications: BP12ACC

  • Maximum Pressure: Approximately 18 psi (1 bar)

  • Air Output: 120 L/min

  • Automatic Stop

SETUP

  • BP12ACC
    • Includes the storage bag with multiple compartments, and inflation hose with adapter.
  • The electric cord has a power connector. The centre button is the positive terminal, the sides are the negative terminal.
  • Screw the hose onto the inflation port on the end of the pump. An access hole with a protective flap allows the hose to be attached without taking the pump out of bag.
  • The power connector must be inserted into 12v accessory power outlet. In a vehicle, the 12v power circuit is protected by a fuse, often rated at 10 to 20 amperes (amps). If the pump stops working before inflation is complete, the fuse may have tripped (see troubleshooting).SEA-EAGLE-BP12ACC-Single-Stage-Electric-Pump-fig-4
  • The power connector can be used with a Minn Kota Power Center or a similar battery box with battery.
  • The recessed Valve Adapter
    • The groove in red gasket must be facing outward. Pull the gasket off and reverse it if necessary. The gasket may be stiff upon first use, stretch or kneed gasket to soften it
  • Recessed ValveSEA-EAGLE-BP12ACC-Single-Stage-Electric-Pump-fig-7
    • The valve stem must be in UP (valve closed) position. Insert the adapter into the valve and twist to the right. The “hooks” on the adapter will lock it into place.
  • Set pressureSEA-EAGLE-BP12ACC-Single-Stage-Electric-Pump-fig-8
    • Turn the dial until the pointer indicates the desired pressure. The photo shows 3.2 PSI. Orange numbers are PSI, and white numbers are bars (metric). Sea Eagle pressure settings are listed to the right, or check boat owner’s manual for the correct setting.
  • Press the ON button to begin inflation. The pump automatically stops once the pressure is met. Do not turn off pump.
  • Keep the pump in a carry bag to make transportation easy and to protect the pump from sand.

Troubleshooting

  • Problem: Pump does not shut off when inflating. Remove hose. Connect the pump to the power source. Turn on and cover the red (out) port to block airflow. If the pump shuts off, it is in working condition. If the pump does not shut off, call Sea Eagle Customer Service, a replacement is needed.
  • Problem: Pump stops working before inflation is complete and won’t restart. The fuse might be blown. Replace fuse, but do not use the pump in that auxiliary power outlet.
  • Problem: Pump smells like it is burning. Turn the pump off and do not try to restart. Unplug from the power supply. Call Sea Eagle Customer Service.
  • Problem: Pump no longer pumps air and is making an unusual noise. The pumping mechanism has broken, call Sea Eagle Customer Service. When calling Sea Eagle Customer Service, please have pump, hose, adapter and power supply available for testing and troubleshooting.

Sea Eagle Boats Inc. 19 N. Columbia Street, Ste1, Port Jefferson, NY 11777

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SEA EAGLE User Manuals

Related Manuals