Savio TWS-01 Bluetooth Earphones User Manual

: June 1, 2024
: Savio

Table of Contents

Savio TWS-01 Bluetooth Earphones
PRODUCT INFORMATION
Product scheme
Charging the device
Content package
Technical specification
Safety conditions
Warranty
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Savio TWS-01 Bluetooth Earphones

Savio-TWS-01-Bluetooth-Earphones-proeduct

PRODUCT INFORMATION

Thank you for choosing Savio products!

If our product meets your expectations, share your opinion with other people on the portal ceneo.pl, social media or on the website of the store where you made the purchase.
If you want to show our device on the SAVIO Facebook Page, we will be very pleased.
If there is something that we could improve on our products, please write to us at support@savio.net.pl.
Thanks to your feedback, we will be able to better adapt the product to your expectations.
Before starting the use of the purchased device it is recommended to read the whole manual.

Product scheme

Multifunctional button
Microphone
Docking station/power bank
Headphone charging input
Power bank charging micro USB input
Diodes signalising operating mode of the power bank
Turn on the button in the power bank

Charging the device

Charging earphones and power bank with the external source of power

Plug the USB cable into the charging socket of the power bank.
Put earphones into the docking station (the red notification light will start to blink, informing about the power bank being charged). Also, the earphone charging will begin (in a case when the earphones are discharged, the diode will light red).
If the power bank is fully charged, then the red diode will flash with constant light.
When the earphones are fully charged, red light will go out. The headphones are ready to use.

Charging earphones with a built in power bank

Put earphones into the docking station (power bank).
The earphones automatically will start to charge placed on the power bank will light blue and the earphones will light red.
When the earphones are fully charged, red light will go out.The headphones are ready to use.

Pairing of the earphones

Earphones Savio TWS-01 / TWS-02 can be used together or separately.
On Default, earphones will connect.
In case when both earphones are connected, and only one works, get to point 3.3 and connect both earphones.

The pairing of the two earphones

Press and hold the multifunction button on both of the earphones till the diode starts to blink red and blue. After proper connection of the earphones, you will hear will hear information about the connection: „Connected”.
Turn the Bluetooth in the device (e.g. smartphone), and choose SAVIO TWS-01 / TWS-02 earphones from Bluetooth devices. Then pair them. If the headphones have already been paired with a device, they will be connected automatically.
After connecting the earphones to the device, the blue diode on the earphones will stop blinking. The earphones are ready to use.

Pairing of one earphone

Press and hold the multifunctional button on the earphone till the diode starts to blink red and blue alternately.
Turn the Bluetooth in the device (smartphone), and choose Savio SAVIO TWS-01 / TWS-02 earphones from Bluetooth devices.
Then pair them. If the headphones have already been paired with a device, they will be connected automatically.
After connecting the earphones to the device, the blue diode on the earphones will stop blinking. The earphones are ready to use.

Connecting two earphones (in the case when both earphones are on, and only one works).

Press and hold the button on each of the earphones. You will hear “Power on”.
Make sure, that your earphones are not connected to any other device through Bluetooth e.g. smartphone
Press the button twice on one of the earphones. If the earphones will connect, you will hear: “Connected”.
Earphones are now connected and ready to use.

Disconnecting two earphones(in the case when both are working and you want to use only one)

Press and hold the button on each of the earphones. You will hear “Power on”
Make sure, that your earphones are not connected to any other device through Bluetooth e.g. smartphone
Press the button twice on one of the earphones. If earphones disconnect with each other, you will hear: “Disconnected”
Earphones are now disconnected and ready to pair the device with one of them.

Multifunctional button description:

Press and hold a multifunctional button for a while turning earphones on and off.

While playing a song

Press once: pause/resume play
Press the button on the right earphone twice: select the previous song
Press the button on the left earphone twice: select the next song
Press the button on the right earphone three times: volume down
Press the button on the left earphone three times: volume up

While the phone calls go in

Press one time: accepting the call
Press and hold a button rejecting the call

Content package

Wireless Bluetooth earphones TWS-01 / TWS-02
Charging cable USB (M) – Micro USB (M)
Docking station power bank
User manual

Technical specification

Bluetooth version: 5.3 + EDR
Range: up to 10 meters
Working time: up to 4 hours
Charging time: up to 1 hour
Total working time: up to 20 h (with use of power bank)
Stand-by time: up to 100 hours
Impedance: 32 Ω
Frequency response: 20Hz – 20 kHz
Build-in microphone: Yes
Microphone sensitivity: -42 ± 3 dB
Indicator diode: Yes
Frequency bands in which the radio equipment operates: 2400 – 2483.5 MHz
Maximum radio-frequency power transmitted in the frequency band in which the radio equipment operates: 4 dBm

Important notice:

It is not necessary to put earphones in the power bank while charging.
Removing the earphones from the power bank will automatically turn them on.
During the phone call, only one of them will be active when two earphones are connected.
Blinking red diode on an earphone will inform you about the low battery level.
When the button placed on the power bank will not react, and an LED will not be backlit, that means, that the power bank is depleted and it needs to be charged.
To extend the battery life of your earphones and power bank, remember to charge them regularly. Leaving your device for a prolonged period without recharging may negatively impact battery performance.

Safety conditions

Use this device as intended.
Incorrect use of the device may damage the device.
It is highly recommended to charge the power bank 1 A charger or charge it from a USB port in the computer.
Independent repairs and modification result in automatic loss ofthe warranty.
Hitting or dropping the device could cause damage to the device.
The device should be used in dry areas, the device should be protected from water and high humidity.

Information for customers and contractors and communication regarding complaints:

Pursuant to Article 13 sections 1 and 2 of the General Data Protection Regulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 (hereinafter referred to as GDPR), please be advised that Elmak Sp. z o.o., with its registered seat at ul.
Morgowa 81; 35-323 Rzeszów becomes the Administrator of your data.
The Specialist for General Data Protection (SODO) can be contacted in writing to: SODO, Elmak Sp. z o.o., ul. Morgowa 81; 35-323 Rzeszów, via e-mail address: sodo@elmak.pl, and by phone at +48 (17) 854 98 14.
Your data will be processed to perform the contract, per Article 6(1)(b) of the aforementioned regulation, to the extent resulting from tax laws and financial regulations.
Recipients of your data include entities authorized by legal regulations to obtain personal data as well as processing entities providing services to Elmak Sp. z o.o.
Your data will be stored based on the Administrator’s legitimate interest.
You have the right to access your data, and the right to rectify, delete or limit the processing of your data.
You have the right to complain to the supervisory body if you believe that the processing violates the GDPR.
The provision of personal data is voluntary, however, a failure to provide such data may result in a refusal to conclude or in termination of a contract.
Your data will not be subjected to automated decision-making, including profiling referred to in Article 22 Sections 1 and 4 of the GDPR of April 27, 2016.

Information on the utilization of electrical and electronic equipment

This symbol indicates that electrical appliances should not be discarded with other household waste.
Used equipment should be handed over to a local collection point for this type of waste or a recycling centre.
Please contact your local authorities for information about disposal methods available in your area. Waste electrical equipment may contain hazardous substances (e.g. mercury, lead, cadmium, chromium, phthalates) which can get into air, soil and groundwater when leaking from used appliances.
Environmental pollution with these substances leads to their bioaccumulation, causing lesions of disease in living organisms, which would pose a risk to human and animal health or life.
Households may contribute to environmental protection by proper waste collection.
In such a way, hazardous substances from the equipment are neutralized and valuable secondary raw materials are reused for the production of new equipment.

Warranty

The warranty covers 24 months. Independent repairs and modifications result in automatic loss of the warranty.
The warranty card is available for download on our website: www.savio.net.pl/en/service.

PRODUCER: