Savio 4-pin 12V Power cable User Manual

Savio 4-pin 12V Power cable

Specifications:

• Product: Savio Fans Kit
• Number of Fans: 3 (1 master fan, 2 secondary fans)
• Control Modes: Motherboard control or manual mode using RESET button
• Power Supply : SATA
• Backlight Control: Motherboard software or manual mode

Product Usage Instructions

1. Pre-Assembly Information:
   The it includes one master fan and two secondary fans. Connect the 12 V and 5 V lines in the specified order.

2. Assembly:

3. Mount the fans inside the PC case using the provided screws.

4. Connect the 12 V and 5 V lines of all fans together.

5. Connect the master fan to the appropriate sockets on the motherboard.

6. Connect the master fan to the power supply and select a fan control option.

7. Fans Backlight Control:
   The fans offer two backlight control options:

   • Control by Motherboard: Use motherboard software if available.
   • Manual Control: Use the RESET button or LED on the PC case for manual backlight control.

FAQ :

• Q: How do I switch between motherboard control and manual mode for backlight?
  A: To switch between control modes, use the RESET / LED button as described in the manual under the backlight selection control modes section.

• Q: What should I do if the fans are not working after assembly?
  A: Double-check all connections and ensure the power supply is properly connected. Refer to the manual for troubleshooting tips.

• Q: Can I use these fans with a different power supply other than SATA?
  A: It is recommended to use the specified SATA power supply for optimal performance and safety.

Set of 3 × 120 mm PC ARGB fans model: BLAST (FAN SET)

User manual

Thank you for choosing Savio product!

• If our product meets your expectations, share your opinion with other people on the portal ceneo.pl, social media or on the website of the store where you made the purchase. If you want to show our device on SAVIO Facebook Page, we will be very pleased.
• If there is something that we could improve on our products, please write to us at support@savio.net.pl
• Thanks to your feedback, we will be able to better adapt the product to your expectations.
• Before starting the use of purchased device it is recommended to read the whole manual.

Technical specification of the fans

• Number of fans in the set: 3 pcs.
• Fan size: 120 mm
• LED voltage: 5 V
• LED connector: 3-pin (male + female)
• Fan voltage: 12 V
• Fan connector: 4-pin (PWM) (male + female)
• Backlight: ARGB
• Additional power supply for the master fan: SATA
• Backlight and speed control: Via motherboard, RESET / LED button
• Max. Speed: 800-1800 RPM
• Max. noise level: 25 dBA
• Max. possible number of fans connected to the master fan: 9 pcs

Set contents

• 1 × ARGB master fan
• 2 × ARGB secondary fans
• 12 × screws for mounting the fan

Pre-assembly information

• The kit consists of one master fan, which we can recognise from the included SATA connector, and two secondary fans. In order to correctly install the kit in the computer, the 12 V  and 5 V lines must be connected in this order, so that the connectors of the master fan are connected directly to the motherboard.
• By default, the fans are set to control mode via the motherboard (3-pin ARGB 5 V), to switch to control mode using the RESET / LED button, go to section “backlight selection  control modes”.

Assembly

1. Mount the fans in a chosen place inside the PC case, securing them with the screws included in the kit.
2. First connect the 12 V and 5 V lines of all the fans together.
3. Connect the master fan to the 3-pin ARGB 5 V and 4-pin 12  V sockets on the motherboard (option for motherboards equipped with a 3-pin ARGB 5 V socket).
4. Connect the master fan to the 4-pin 12 V socket on the mother- board and also connect the SW lines with the LED / RESET cable from your case (option for motherboards without a 3-pin ARGB 5 V socket).
5. Connect the SATA power supply for the master fan. 4.6 Select one of two available fan control option.

Fans backlight control:
The fans have two variants of backlight control.

1. Backlight control by motherboard:
   If the motherboard has 3-pin ARGB 5 V socket, the backlight can be controlled by using a dedicated motherboard software.

2. Backlight control by manual mode using the RESET button or the LED on the PC case.
   If the motherboard does not have a 3-pin ARGB 5 V connector, the backlight can be controlled using the RESET or LED button (if the computer case has a dedicated button) located on the top of the housing.

ATTENTION!
If this control method is selected, after turning off the computer, the backlight colour of the fans will not be remembered and the basic colour will be restored.

Backlight selection control modes.
If the master fan is connected at the same time to the motherboard and RESET / LED button, only one mode of backlight control will work properly. To change backlight mode control you need to:

1. Press the RESET / LED button placed on the top part of case for  about 3 sec.

Safety conditions

• Use the product in accordance with its intended use, as improper use may damage the product.
• Do not expose the device to moisture, heat or sunlight, do not use the product in a dusty environment.
• The device should be cleaned only with a dry cloth.
• Independent repairs and modification result automatic loss of the warranty.
• Hitting or dropping may damage the product.

Warranty

The warranty covers a period of 24 months. Independent repairs and modifications result in automatic loss of the warranty. Warranty card is available for download on our website:
www.savio.net.pl/en/service

Information of the utilization of electrical and electronic equipment

• This symbol indicates that electrical appliances should not be discarded with other household waste. Used equipment should be handed over to a local collection point for this type of waste or to a recycling center. Please contact your local authorities for information about disposal methods available in your area. Waste electrical equipment may contain hazardous substances (e.g. mercury, lead, cadmium, chromium, phthalates) which can get into air, soil and groundwater when leaking from used appliances. Environmental pollution with these substances leads to their bioaccumulation, causing lesion of disease in living organisms, which would pose a risk to human and animal health or life.
• Households may contribute to environmental protection by proper waste collection. In such way, hazardous substances from the equipment are neutralized and valuable secondary raw materials are reused for production of new equipment

Information for customers and contractors and communication regarding

complaints

• Pursuant to Article 13 section 1 and 2 of the General Data Protection Regulation (EU) 2016/679 of the European Parliament and of the Council of 27 April 2016 (hereinafter referred to as GDPR), please be advised that Elmak Sp. z o.o., with its registered seat at ul. Morgowa 81; 35-323 Rzeszów becomes the Administrator of your personal data. The
• Specialist for General Data Protection (SODO) can be contacted in writing to: SODO, Elmak Sp. z o.o., ul. Morgowa 81; 35-323 Rzeszów, via e-mail address: sodo@elmak.pl, and by phone at +48 (17) 854 98 14. Your personal data will be processed in order to perform the contract, in accordance with Article 6(1)(b) of the aforementioned regulation, to the extent resulting from tax laws and financial regulations. Recipients of your personal data include entities authorized by legal regulations to obtain personal data as well as processing entities providing services to Elmak Sp. z o.o. Your personal data will be stored on the basis of Administrator’s legitimate interest. You have the right to access your data, and the right to rectify, delete or limit processing of your data. You have the right to lodge a complaint to the supervisory body if you believe that the processing violates the GDPR.
• The provision of personal data is voluntary, however, a failure to provide such data may result in a refusal to conclude or in termination of a contract. Your personal data will not be subjected to automated decision ma-king, including profiling referred to in Article 22 section 1 and 4 of the GDPR of April 27, 2016.

PRODUCER

• Elmak Sp. z o.o.
• ul. Morgowa 81
• 35-323 Rzeszow
• www.savio.net.pl

References

• Strona główna - Savio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>