MAXVIEW Antslim Mini 5G 2X2 MIMO Antenna Installation Guide

: June 1, 2024
: MAXVIEW

MAXVIEW Antslim Mini 5G 2X2 MIMO Antenna

MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Product

Product Information

Specifications

Antenna Type: Omni-directional
Frequency/Gain: 698-6000 MHz/5.9dBi-8.8dBi
Connector Type: 2 x SMA
Impedance: 50 Ohm
Power: Passive
Cable Lengths: 0.8m as standard
Housing: Aluminium Base, UV Stable ASA Cover
Dimensions: H: 67mm x W: 180mm x D: 60mm
Weight: 385g

Product Usage Instructions

Installation Instructions

Positioning your Antenna: Mount the antenna near the router for best performance.
Important Antenna Installation Information: Leave a 30cm gap around the antenna to avoid interference issues.
Fitting the Antenna: Follow the provided fixing template and use the included screws for installation.

Additional Information

General Safety Warnings: Follow all safety precautions during installation.
Terms and Conditions: Refer to the terms and conditions provided by Maxview.
Maintenance: Regularly clean the antenna and check for any damage.
2-Year Guarantee: The product comes with a 2-year guarantee.
Certification and Environment: The product is certified and designed for environmental durability.

Accessories – Sold separately
Additional accessories such as a bracket fixing kit, extension cables, and weatherproof sockets are available for separate purchases to enhance antenna functionality.

Positioning your Antenna

Distance between Router and Antenna: For optimal performance, keep the router close to the roof-mounted antenna and avoid unnecessary extension cables.
Roof Antenna Position: Mount the antenna on a horizontal flat roof with a 30cm gap from obstacles to prevent interference.

FAQ

Q: Can I use extension cables longer than 5 meters with this antenna?
A: It is recommended not to use extension cables longer than necessary for best performance.
Q: Is the antenna weatherproof?
A: The antenna housing is designed with a UV-stable ASA cover for weather resistance.

Introduction

Thank you for purchasing this product, should you have any difficulty using your Antenna please contact our friendly Customer Helpline at +44 (0)1553 811000 or email support@maxview.co.uk.

Product Contents

A. Omni-directional Roof Mount Antenna and 0.8m cables with SMA connectors
B. Roof Clamp
C. No. 6 Screws (spares included)
D. Fixing Template
E. SMA to TS9 Adaptor X 2

$MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Fig- $1$$

Tools Required

Power Drill
2.5mm Drill Bit
25mm Hole Saw
Cross Head Screwdriver
Hack Saw
File/Emery Paper
Surface Cleaner

Specifications

Antenna

Type: Omni-directional 2×2 MIMO (multiple in multiple out)
Frequency/Gain: 698-6000 MHz/5.9dBi-8.8dBi. Includes all 3G, 4G and 5G frequencies
Connector Type: 2 x SMA
Impedance: 50 Ohm
Power: Passive
Cable Lengths: 0.8m as standard
Housing: Aluminium Base. UV Stable ASA Cover
Dimensions: H: 67mm x W: 180mm x D: 60mm
Weight: 385g

Accessories

Sold separately

$MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Fig- $2$$

Bracket Fixing Kit – For roof mounting
The raiser bracket allows you the flexibility to mount your antenna anywhere on your roof and enter the cable at your preferred point using the supplied cable entry cover. Alternatively, you may have an existing cable entry point you would like to utilise instead. Designed and manufactured specifically for the Antenna, the aluminium bracket is lightweight, strong and finished with a durable white or black powder coating. Suitable for any flat roof the kit also includes 3m extension cables for flexible mounting position.

MXL060/KIT White
MXL060/GKIT Black

Weatherproof Socket with SMA Connectors
The Weatherproof Socket provides an external entry point into the side of any vehicle. Available with 2 SMA connections, making it ideal when using the Roam Antenna with the Roam Bracket Fixing Kit (See left) to allow for a temporary connection or where entry into the roof is not possible. It can also be used for other applications where an external SMA connection is required.

B2016

Roam Extension Cables
Extension cables can be purchased separately to allow a flexible mounting position to the router.

metre MXL050/EXT1
metres MXL050/EXT2
metres MXL050/EXT3
metres MXL050/EXT5

Thread Extender
Can be used to fit all Roam Antennas to thicker vehicle roofs. For example American RV’s, Winterised Motorhomes and Over Landing vehicles. Thread Extender is ideal for roofs 50 – 90mm thick.

MXL050/TE

Positioning your Antenna

Distance between Router and Antenna
For best performance, we recommend mounting the router near the roof-mounted antenna. For best performance, do not use extension cables that are no longer than necessary.
Roof Antenna Position
We recommend leaving a 30cm gap from obstacles around the antenna to avoid interference issues and mounting on a horizontal flat roof.

Important Antenna Installation Information

The 3M seal provides a permanent installation. The adhesive is extremely strong and the antenna is not designed to be removed. Please ensure you are completely happy with your antenna’s position and orientation before installation.
The Mini Antenna is designed to be mounted directly to a horizontal, flat and smooth surface such as GRP (Glass Reinforced Plastic) with the coaxial cables passing directly through the roof underneath the centre of the antenna. The standard installation is designed for roof thicknesses from 10mm up to 50mm. $MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Fig- $5$$

Fitting the Antenna

Once you have a suitable position for the antenna, cut out the supplied template. Use to mark the 25mm centre hole position and mark the outside of the antenna.
At the marked centre position, drill a 2.5mm pilot hole through the roof. Use a 25mm hole saw to drill out the centre hole through the roof. Tidy up the hole to remove the swarf and sharp edges. $MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Fig- $6$$
Use the Antenna clamp to gauge the depth of the roof. The best way to do this is to sit the Antenna clamp upside down through the hole. Then, from the inside, mark the clamp where the clamp passes through the ceiling and into the vehicle.
- 3A. Please Note. An alternative Nut and Washer option for thin metal roof applications is supplied. If this is better suited for your application ignore steps 3 & 4.
Remove the clamp and cut the clamp shaft to the correct length. The correct length for your installation will be the roof depth minus 3mm. This will ensure the clamp does not bottom out on the antenna when tightened. E.g. If the roof depth is 30mm. The clamp shaft should be cut 27mm along the shaft. $MAXVIEW-Antslim-Mini-5G-2X2-MIMO-Antenna-Fig- $7$$
Clean the surface where the antenna will be installed, ensuring it is free from debris and grease.
Pass the cables through the hole and remove the self-adhesive backing from the 3M seal. Pass the cables through the roof and position the antenna making sure it’s facing the front of the vehicle -Please reference Picture 7 below.
- IMPORTANT – Ensure the position of the antenna is central to your markings, as once stuck down, the antenna is not designed to be removed.
Press firmly around the edges of the antenna to ensure a watertight seal has been achieved.
From the inside of the vehicle, attach the clamp and turn clockwise onto the thread protruding from the bottom of the antenna. Continue to turn until the clamp is compressing the seal underneath the antenna. Once in position, use 1 x No.6 Screw to secure the clamp in position.
- 8A. If using the Nut and Washer Option (ref page 5) please tighten and secure using a 27mm Spanner.
The Antenna is now installed and ready to be connected to a suitable 4G/5G Router.

General Safety Warnings

Read these instructions carefully and become familiar with your Maxview product. Understand the application, limitations and any hazards involved with the installation and operation. Failure to follow all instructions may result in damage to your vehicle and/or serious injury. Maxview declines all responsibility in the event of an incident or accident if they are due to a non-observation of the installation instructions or the way the product is used. No modifications to the product are permissible.

Installation

Always consider the additional height the product you install adds to the vehicle
Always follow the manufacturer’s operating instructions before using tools and equipment.
Take care when working at heights. Keep the work area clean and tidy to avoid trip hazards
Use creeper boards where necessary to ensure roof construction can support your weight
All electrical work should be carried out by a competent person

Operation
The maximum speed of the vehicle with the product mounted on the roof is 81mph (130km/h)

Servicing & Support

Any inspection or repair must be carried out by Maxview or an appointed representative of the manufacturer
No regular maintenance is required on the product
Do not dismantle the product
Do not use solvent or abrasive cleaning agents on the product
Only use a suitable mild detergent to clean the product
Do not pressure wash the product
We recommend you check the mechanical integrity of a roof-mounted product afar
If in the event that you do experience a problem with the product, call Maxview Customer Service + 44 (0)1553 811000

Maintenance

The antenna has been designed to be maintenance and trouble-free. For optimum signal strength, keep the cover clean from dirt, bugs, and other debris. Periodic washing of the top cover with mild soap and water is recommended.

Do not remove the cover of the antenna as it will void the limited guarantee.
Never power wash the antenna. Keep the enclosure clean from dirt, bugs, and other debris by hand washing with mild soap and water.

DO NOT USE SOLVENTS TO CLEAN THE ROAM. DO NOT DROP OR EXPOSE TO JARRING MOVEMENTS.

Terms and conditions

In no event shall Maxview be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies both during and after the terms of the guarantee. This does not affect your statutory rights. The antenna is designed for permanent installation and is not designed to be removed or serviced. Whether the antenna is under warranty or not and whether the cause for removal is our fault or not, we are not responsible for the safe removal of the antenna. We will not be held responsible or liable for any damage done to the antenna or other property whilst removing the antenna, regardless of the reason for removal.

2-year guarantee

Every Maxview Antenna is covered by the following 2-year parts limited guarantee from the date of original purchase.

How do I claim on my guarantee?

In the unlikely event that you have an issue with your product please contact our Customer Services Team at +44 (0) 1553 811000 or email support@maxview.co.uk. You will need to retain your proof of purchase.
In no event shall Maxview be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies both during and after the terms of the guarantee. This does not affect your statutory rights.
Due to the expanding and changing telecommunications market, Maxview cannot be held responsible for changes made to communication services. Software updates to address such issues are not covered under guarantee.

Terms and Conditions of the Guarantee

Your guarantee starts from the date you purchased your item. Your guarantee will be valid from the date of manufacture if you are unable to provide proof of purchase.
A guarantee authorisation must be obtained from Maxview before work commences.
Maxview is responsible for the cost of a replacement part if the original part is determined to be defective under the terms of the guarantee.
Any replacement parts required will be supplied, by return, on receipt of the faulty part.
Any work requiring replacement parts will only be sanctioned on receipt of proof of the broken part. The customer is responsible for the cost of replacement parts after the guarantee period has expired.
Our guarantee is “Back To Base.” No travelling costs will be paid.
Parts that suffer breakdown and/or failure due to flooding/water ingress or abrasive cleaning caused by solutions and/or Pressure Washers are not covered under our guarantee.
Our guarantee does not cover installation or external wiring.

This guarantee also does not apply where:

The product has been abused, misused, improperly installed or improperly maintained.
The product has been installed without the use of a Maxview mounting bracket designed for the product.
Repairs have been made or attempted by others who are not certified by Maxview to do such repairs.
Repairs are required because of normal wear and tear.
Alterations have been made to the product.
The antenna unit has been opened without authorisation.
Damage has been caused by power washing.
Circumstances beyond the control of Maxview cause the product to no longer operate correctly.
The customer is not the original owner.

Certification and Environment

The Antenna has been designed, constructed and marketed in compliance with the safety and product requirements of the relevant EEC Directives.
Products marked with the crossed-out wheely bin must not be disposed of with normal household waste but made available for separate household collection. A separate collection of used products and their packaging allows materials to be recycled and used again. The reuse of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
UK Conformity Assessed (UKCA) marking is a certification mark that indicates conformity with the applicable requirements for products sold within Great Britain.