WALLYS DR9574 Communications WiFi Routerboard and Wifi Network User Manual
- June 1, 2024
- WALLYS
Table of Contents
DR9574
User Manual
1. IPQ9574 UI settings
2. DR9574 UART configuration
3. How to set up the card slot
THIS DOCUMENT CONTAINS PROPRIETARY TECHNICAL INFORMATION, WHICH IS THE PROPERTY OF THE WALLYSTECH AND SHALL NOT BE DISCLOSED TO OTHERS IN WHOLE OR IN PART, REPRODUCED, COPIED, OR USED AS THE BASIS FOR DESIGN, MANUFACTURING, OR SALE OF APPARATUS WITHOUT WRITTEN PERMISSION OF WALLYSTECH.
IPQ9574 UI setting
1. Input the IP 192.168.1.1 and login
2. Input the username “admin” password “password” then press the button
“Login”
3. Network setting
- IP Setting: setting IP in the path “network->Interfaces->LAN->IPV4 address”
- DHCP setting:DHCP and other protocol setting in the path network-> Interfaces-> LAN->protocol”
4. Wireless setting
Login the path network->Interfaces->WIFI,Then choose wifi 1,we select the red
marked as example,click the button “ Edit ”
The detail information show in the picture as below:
- Channel:for channel select;
- Transmit Power:signal chain power setting; ESSID:for ID
- Mode:it support 4 mode AP,AP(WDS),client,client(WDS) Wireless
- Security: for Encryption setting
In advance setting you can select which chain do you need,which BW do you need and so on
In the end, you need click the button “Save & Apply”, and wait for 2 minutes, then you can enjoy it.
5. Backup archive
Login System->Backup/Flash Firmware; Then click the button “Generate
archive”Then download the archive
6. Update new image
Login System->Backup/Flash Firmware;Then click the button “ flash image” Then
click the button “Proceed” warning don’t power off wait for about three
minutes Then the system will reboot automatic.Then login again,you can enjoy
it.
7. wireless encryption
Login System->Network/wifi/Edit->Choose 5G radioCountry Coad choose “ US ”
click the button“Wireless Security” Then choose “WPA3” and set password
Notice: SAE/SAE PWE/SAE MFP click “ √ ”
7. wireless encryption
DR9574 UART configuration
1. Introduction
The photo below shows how to use the Uart for DR9574
2. Device connect
Step 1: Connect the cable to the DR9574As the picture as above,the sequence of
the signal in the UART
Connector: GND,TX,RX,VCC, And we need use GND connect black cable,TX connect
to white cable,RX connect toGreen cable VCC don’t use.
Step 2: Check the Com number on the PCConnect the console board to the PC with
USB connector, Then check the com number on the PC,the com number on the test
PC is COM9
2. Device connect
Step 3 Login with the softwareYou can use putty,Xshell or some others,enjoy
it.
How to set up the card slot
4×4 single radio
setenv machid 8050e01
setenv bootargs ‘console=ttyMSM0,115200n8 cnss2.enable_qcn9224_support=1
cnss2.bdf_pci2=0x0002 cnss2.bdf_pci3=0x0004 cnss2.enable_mlo_support=0’saveenv
2×2 dual radio
setenv machid 8050e01
setenv bootargs ‘console=ttyMSM0,115200n8 cnss2.enable_qcn9224_support=1
cnss2.bdf_pci2=0x1006 cnss2.bdf_pci3=0x1003 cnss2.enable_mlo_support=0’saveenv
0002 represent DR9274-5G radio
0004 represent DR9274-6G radio
1006 represent DR9274-5G6G radio
1003 represent DR9274-2.4G5G radio
You can configure the DR9274 card slot 0-3 as desired
For example set one card
if you want pcie 0 support DR9274-5G;you can under uboot
enter cnss2.enable_qcn9224_support=1 cnss2.bdf_pci0=0x0002
cnss2.enable_mlo_support=0’than saveenvthan reset.
For example set one card
if you want pcie 2 support DR9274-5G;you can under uboot
enter cnss2.enable_qcn9224_support=1 cnss2.bdf_pci2=0x0002
cnss2.enable_mlo_support=0’than saveenvthan reset.
For example set two card
if you want pcie 3 support DR9274-5G;
pcie 2 support DR9274-6G;you can under ubootenter setenv bootargs
‘console=ttyMSM0,115200n8
cnss2.enable_qcn9224_support=1 cnss2.bdf_pci3=0x0002 cnss2.bdf_pci2=0x0004
cnss2.enable_mlo_support=0’than saveenv than reset.
THIS DOCUMENT CONTAINS PROPRIETARY TECHNICAL INFORMATION, WHICH IS THE PROPERTY OF THE WALLYSTECH AND SHALL NOT BE DISCLOSED TO OTHERS IN WHOLE OR IN PART, REPRODUCED, COPIED, OR USED AS THE BASIS FOR DESIGN, MANUFACTURING, OR SALE OF APPARATUS WITHOUT WRITTEN PERMISSION OF WALLYSTECH.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>