WALLYS DR8072 Discover the Power and Versatility User Manual
- June 1, 2024
- WALLYS
Table of Contents
WALLYS DR8072 Discover the Power and Versatility
Product Specifications
- Model: DR8072
- Processor: IPQ8072
- Interface: UART
- Wireless Standards: 802.11ac
- Wireless Encryption: WPA3
Product Usage Instructions
- Input the IP 192.168.1.1 and login.
- Input the username admin and password password, then press the Login button.
- Network Setting: Visit www.wallystech.com for further details.
- Wireless Setting: Navigate to network->Interfaces->WIFI, choose wifi 1, edit settings as needed, and click Save & Apply.
- Backup Archive: Go to System->Backup/Flash Firmware, generate and download the archive.
- Update New Image: Access System->Backup/Flash Firmware, flash the image and wait for the system to reboot automatically.
- Wireless Encryption: Configure wireless security settings under System->Network/wifi/Edit, choose 5G radio, set WPA3 encryption, and set a password.
DR8072 UART Configuration
- Device Connect:
- Step 1: Connect the cable to the DR6018 following the signal sequence: GND, TX, RX, VCC.
- Step 2: Check the COM number on the PC after connecting the console board using a USB connector.
- Step 3: Log in with software like Putty or Xshell.
FAQ
- Q: Can I change the default username and password for the IPQ8072 UI settings?
- A: Yes, you can change the default username and password for increased security. Simply access the login page and update the credentials under settings.
- Q: How often should I back up the firmware on DR8072?
- A: It is recommended to backup the firmware periodically, especially before any significant system changes or updates, to avoid data loss.
THIS DOCUMENT CONTAINS PROPRIETARY TECHNICAL INFORMATION, WHICH IS THE PROPERTY OF WALLYSTECH AND SHALL NOT BE DISCLOSED TO OTHERS IN WHOLE OR IN PART, REPRODUCED, COPIED, OR USED AS THE BASIS FOR DESIGN, MANUFACTURING, OR SALE OF APPARATUS WITHOUT WRITTEN PERMISSION OF WALLYSTECH.
IPQ8072 UI setting
- Input the IP 192.168.1.1 and login
- Input the username “admin” password “password” then press the button “Login”
Network setting
- IP Setting: setting IP in the path “network->Interfaces->LAN- >IPV4 address”
- DHCP setting: DHCP and other protocol settings in the path network-> Interfaces-> LAN->protocol”
Wireless setting
- Login the path network->Interfaces->WIFI,
- Then choose wifi 1, select the red marked as an example, and click the button “ Edit ”
IPQ8072 UI setting
The detailed information is shown in the picture below:
- Channel: for channel select;
- Transmit Power: signal chain power setting; ESSID: for ID
- Mode:it support 4 mode AP,AP(WDS),client,client(WDS) Wireless
- Security: For encryption setting
IPQ8072 UI setting
In the advanced setting, you can select which chain you need, which BW you
need and so on
- In the end, you need to click the button “Save & Apply”, and wait for 2 minutes, then you can enjoy it.
Backup archive
- Login System->Backup/Flash Firmware;
- Then click the button “Generate archive”
- Then download the archive
Update new image
- Login System->Backup/Flash Firmware;
- Then click the button “ flash image”
- Then click the button “Proceed” warning don’t power off wait for about three minutes
- Then the system will reboot automatically.
- Then log in again, and you can enjoy it.
Wireless encryption
- Login System->Network/wifi/Edit->Choose 5G radio
- Country Coad choose “ US ” and click the button“Wireless Security”
- Then choose “WPA3” and set a password
- Notice: SAE/SAE PWE/SAE MFP click “ √ ”
Wireless encryption
Introduction
- The photo below shows how to use the UART for DR6018
DR8072 UART configuration
Device Connect
- Step 1: Connect the cable to the DR6018 As in the picture above, the sequence of the signal in the UART Connector: GND, TX, RX, VCC, And we need to use GND connect black cable, TX connect to white cable, RX connect to Green cable VCC don’t use.
- Step 2: Check the Com number on the PC Connect the console board to the PC with a USB connector, Then check the com number on the PC, the com number on the test PC is COM9
- Step 3: Log in with the software You can use Putty, Xshell or some others, enjoy it.
THIS DOCUMENT CONTAINS PROPRIETARY TECHNICAL INFORMATION, WHICH IS THE PROPERTY OF WALLYSTECH AND SHALL NOT BE DISCLOSED TO OTHERS IN WHOLE OR IN PART, REPRODUCED, COPIED, OR USED AS THE BASIS FOR DESIGN, MANUFACTURING, OR SALE OF APPARATUS WITHOUT WRITTEN PERMISSION OF WALLYSTECH.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>