GRANBERG 116.540 Cut Resistant Gloves Protector User Manual

Cut Resistant Gloves Protector
User Manual

116.540 Cut Resistant Gloves Protector

ART. 116.540
1 pair
cat. II
SIZE 7/S (EN 420:2003+A1:2009)

Slitestyrke
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
EN 420:2003+A1:2009

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and has been shown to comply with this
Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN 388:2016.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/116.540

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.

User Manual issue date: 10.02.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY
Typhoon fibered yarn shell with PU coating offering protection against cuts. Excellent dexterity. White color. ® Sanitized treated to prevent bacteria growth and promote freshness.
Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.

Maintenance/Cleaning

Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select
a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Gloves can only be cleaned with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.

Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the require- ment for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in cases of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environments in accordance with EN 388:2016 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer. Contains biocidal substance: zinc pyrithione. Feel the difference of Sanitized treated odor-resistant articles. Sanitized has no products with nano material.

ART. 116.540
1 pair
cat. II
SIZE 7/S (EN 420:2003+A1:2009)

Slitestyrke
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
EN 420:2003+A1:2009

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and has been shown to comply with this Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN 388:2016.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/116.540

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.

User Manual issue date: 10.02.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY
Typhoon fibered yarn shell with PU coating offering protection against cuts. Excellent dexterity. White color. ® Sanitized treated to prevent bacteria growth and promote freshness.
Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.

Maintenance/Cleaning: Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Gloves can only be cleaned with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the require- ment for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in cases of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environments in accordance with EN 388:2016 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer. Contains biocidal substance: zinc pyrithione. Feel the difference of Sanitized treated odor-resistant articles. Sanitized has no products with nano material.

** ART. 116.540
1 pair
cat. II
SIZE 7/S (EN 420:2003+A1:2009)**

Slitestyrke
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
EN 420:2003+A1:2009

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and has been shown to comply with this Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN 388:2016.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/116.540

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.

User Manual issue date: 10.02.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY

Typhoon fibered yarn shell with PU coating offering protection against cuts. Excellent dexterity. White color. ® Sanitized treated to prevent bacteria growth and promote freshness.
Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.
Maintenance/Cleaning: Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Gloves can only be cleaned with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the require- ment for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in cases of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environments in accordance with EN 388:2016 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer. Contains biocidal substance: zinc pyrithione. Feel the difference of Sanitized treated odor-resistant articles. Sanitized has no products with nano material.

ART. 116.540
1 pair
cat. II
SIZE 7/S (EN 420:2003+A1:2009)

Slitestyrke
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
EN 420:2003+A1:2009

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and has been shown to comply with this Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN 388:2016.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/116.540

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.

User Manual issue date: 10.02.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY

Typhoon fibered yarn shell with PU coating offering protection against cuts. Excellent dexterity. White color. ® Sanitized treated to prevent bacteria growth and promote freshness.
Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.

Maintenance/Cleaning: Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Gloves can only be cleaned with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the require- ment for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in cases of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environments in accordance with EN 388:2016 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer. Contains biocidal substance: zinc pyrithione. Feel the difference of Sanitized treated odor-resistant articles. Sanitized has no products with nano material.

ART. 116.540
1 pair
cat. II
SIZE 7/S (EN 420:2003+A1:2009)

Slitestyrke
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
EN 420:2003+A1:2009

This product is classed as Category II Personal Protective Equipment (PPE) according to PPE Regulation (EU) 2016/425 and has been shown to comply with this Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN 388:2016.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from https://www.granberg.no/catalog/116.540

Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.

User Manual issue date: 10.02.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY

Typhoon fibered yarn shell with PU coating offering protection against cuts. Excellent dexterity. White color. ® Sanitized treated to prevent bacteria growth and promote freshness.
Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.

Maintenance/Cleaning: Both new and used gloves should be inspected before use, and before putting them on to make sure that there is no damage to them. If in doubt, discard the gloves and select a new pair. Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Gloves can only be cleaned with damp cloth, but it will not stop permeation processes.
Obsolescence: When stored as recommended, unused gloves will not suffer any change in their mechanical properties for up to three years from the date of manufacture. Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the glove by the cuff with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each finger. Pull by the glove cuff and align fingers into the right position. Use the same procedure for the other hand. If gloves are not contaminated, pull by the fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff and pull toward the finger until the gloves come off.

Please note: Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the require- ment for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in cases of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environments in accordance with EN 388:2016 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer. Contains biocidal substance: zinc pyrithione. Feel the difference of Sanitized treated odor-resistant articles. Sanitized has no products with nano material.

References

• Cut Resistant Gloves Protector | Granberg - Work and Safety Gloves Solutions

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>