PRINCE CASTLE 755-HM10 Multi-Display 10-Channel and 16-Channel Timers User Manual
- June 4, 2024
- PRINCE CASTLE
Table of Contents
PRINCE CASTLE 755-HM10 Multi-Display 10-Channel and 16-Channel Timers
Product Identification
The Prince Castle Model 755 Series Multi-display 10-Channel Timer and 16-Channel Timer are easy-to-use timers that count down in minutes and seconds, or hours and minutes. Each channel has its own display and can be programmed independently. Slide in replaceable menu strips identify the product being timed on each channel, and are replaceable as restaurant menus change. Both auditory and visual signals are used to alert busy staff people when a function is complete.
LIMITED WARRANTY
This product is warranted to be free from defects in material and/or workmanship for a period of 1 year from date of original installation, not to exceed 18 months from the date of manufacture. Any component which proves to be faulty in material and/or workmanship will be replaced or repaired (at the option of Prince Castle, Inc.) without cost to the customer for parts and labor. This equipment is portable; charges for on-location service (e.g., trip charges, mileage) are not included in the provisions of this warranty. This warranty is subject to the following exceptions/conditions:
- Use of any non-genuine Prince Castle parts voids this warranty.
- All labor to be performed during regular work hours. Overtime premium (the incremental amount) will be charged to the customer.
- Damage caused by carelessness, neglect and/or abuse (e.g., dropping, tampering or altering parts, equipment damaged in shipment, by fire, flood or an act of God) is not covered under this warranty.
- All problems due to operation at voltages other than that specified on equipment nameplates are not covered by this warranty. Conversion to correct voltage is the customer’s responsibility.
- This equipment must be serviced by Prince Castle Authorized Service Agency or a Prince Castle Service Technician during the warranty period.
The power cord on this product is rated for a maximum surface temperature of 194 °F (90 °C ). If the cord comes into contact with the fryer or thermalized or any other heated surface, it may be damaged and/or cause damage to the product and/or injury to the user. The power cord may also be damaged if placed directly in the path of the high temperature exhaust emitting from the flue of the fryer or thermalized. Damage resulting from any such misuse may result in a voided Warranty at the sole discretion of the manufacturer.
Safety Information
WARNING: Indicates information important to the proper operation of the
unit. Failure to observe may result in damage to the equipment and/or severe
bodily injury or death.
CAUTION: Indicates information important to the operation of the unit.
Failure to observe may result in equipment damage.
Important! Prince Castle reserves the right to change specifications and
product design without notice. Such revisions do not entitle the buyer to
corresponding changes, improvements, additions or replacements for previously
purchased equipment.
Installation
Remove the unit from the carton and inspect for signs of damage. If there is damage to the unit:
- Notify the freight carrier (e.g. UPS) within 24 hours,
- Save carton and packaging materials for inspection purposes,
- Contact your local dealer, or if purchased directly, the Prince Castle Sales Department at 1-800-722-7853 or 630-462-8800 to arrange for a replacement unit.
NOTE: When installing this unit, the ambient temperature at the mounting
site should not exceed 100°F (37.8°C).
CAUTION: All electrical connections must be in accordance with local
electrical codes and any other applicable codes. Plug the unit into an
applicable electrical receptacle.
Cleaning
Use ONLY a clean damp cloth, and wipe the face and other surfaces on the Model 755 Series Timer, as necessary. If desired, a mild soap may also be used. NEVER use chemicals and/or degreaser of any kind! Long-term use of certain chemicals has a negative effect on the surface of the timer, making it brittle and easily damaged.
Operation
- When a channel’s timing cycle has been activated its individual display will show the timing countdown of that channel.
- If the time is in Hours-Minutes (H:M) the colon in the middle of the 4-digits will flash. If the time is in Minutes-Seconds (M:S) the colon in the middle of the 4-digits will be on continuously.
- At the conclusion of a timing cycle, the display flashes “0”.
- At the conclusion of a timing cycle, the display will show either “diSc” for discard or “done” for doing. This indication is programmable.
Each of the channels of the 10-Channel or 16-Channel timers operates in an
identical manner. Press a channel button to activate a timing cycle (a short
beep sound). The timers can be programmed to count up to a selected value or
count down to 0:00.
NOTE: To cancel any operation in progress, press the related channel
button three times in quick succession (less than three seconds). The channel
LED turns off and the LED of the next channel with the lowest countdown
remaining will blink. At the conclusion of a timing cycle, the display will
show either “diSc” or “donE” depending on how it is programmed. Two different
timing cycles can be set up for each channel. These are called “Menu 1” and
“Menu 2”. To change from one menu to the other, all channels must be idle.
Simultaneously press both the UP and DOWN buttons for 6 seconds. The display
will change between the single-line display (Menu 1) and the three-line
display (Menu 2).
Channel Defaults
HM10
Menu 1 | |
---|---|
Cycle Time | |
Time | |
Channel 1 | 30:00 |
Channel 2 | 30:00 |
Channel 3 | 30:00 |
Channel 4 | 30:00 |
Channel 5 | 30:00 |
Channel 6 | 30:00 |
Channel 7 | 30:00 |
Channel 8 | 30:00 |
Channel 9 | 04:00 |
Channel 10 | 04:00 |
Bold italic times are in Hours: Minutes. All other times are in
Minutes: Seconds. Alert time = 0 (feature turned off).
HM10
Menu 2 | |
---|---|
Cycle Time | |
Time | |
Channel 1 | 30:00 |
Channel 2 | 30:00 |
Channel 3 | 30:00 |
Channel 4 | 30:00 |
Channel 5 | 30:00 |
Channel 6 | 30:00 |
Channel 7 | 30:00 |
Channel 8 | 30:00 |
Channel 9 | 04:00 |
Channel 10 | 04:00 |
Bold italic times are in Hours:Minutes. All other times are in
Minutes:Seconds. Alert time = 0 (feature turned off).
HM16
Menu 1 | |
---|---|
Cycle Time | |
Time | |
Channel 1 | 15:00 |
Channel 2 | 15:00 |
Channel 3 | 15:00 |
Channel 4 | 15:00 |
Channel 5 | 15:00 |
Channel 6 | 15:00 |
Channel 7 | 15:00 |
Channel 8 | 15:00 |
Channel 9 | 30:00 |
Channel 10 | 30:00 |
Channel 11 | 30:00 |
Channel 12 | 30:00 |
Channel 13 | 30:00 |
Channel 14 | 30:00 |
Channel 15 | 30:00 |
Channel 16 | 30:00 |
Bold italic times are in Hours:Minutes. All other times are in
Minutes:Seconds. Alert time = 0 (feature turned off).
HM16
Menu 2 | |
---|---|
Cycle Time | |
Time | |
Channel 1 | 15:00 |
Channel 2 | 15:00 |
Channel 3 | 15:00 |
Channel 4 | 15:00 |
Channel 5 | 15:00 |
Channel 6 | 15:00 |
Channel 7 | 15:00 |
Channel 8 | 15:00 |
Channel 9 | 30:00 |
Channel 10 | 30:00 |
Channel 11 | 30:00 |
Channel 12 | 30:00 |
Channel 13 | 30:00 |
Channel 14 | 30:00 |
Channel 15 | 30:00 |
Channel 16 | 30:00 |
Bold italic times are in Hours:Minutes. All other times are in Minutes:Seconds. Alert time = 0 (feature turned off).
Programming
Timer Programming
To program the timer, all 10 or 16 timing channels must be idle with the
display showing either one or three sets of four dashes and all LED’s turned
off. A single set of dashes is shown to program Menu 1 and three sets of
dashes are shown to program Menu 2.
Entering Program Mode
Press and hold the Prince Castle logo button for 6-8 seconds to enter the
Programming Mode. The display changes to “Prog” and all channel LED’s turn
red.
Countdown Mode
NOTE: This mode can only be entered when all channels are idle.
Enter the Countdown Mode by holding the UP button for 6 seconds. This will
determine if all the timing cycles count up from 0:00 or count down to 0:00.
Use the UP or DOWN buttons to toggle between count up or count down. Display 1
will indictor “C-uP” or “C-dn”. When the desired mode is obtained, momentarily
press any channel button to save it and return to Timing Mode.
NOTE: To return to Timing Mode without saving, momentarily press the
Prince Castle logo button.
Volume Level Selection
NOTE: This mode can only be entered when all channels are idle.
Press and hold the DOWN button for 6 seconds to initiate the Volume Level
Setup Mode. In this mode the timer’s audio volume can be set to one of three
different levels by using the UP and DOWN buttons. A display will sequence
through “SL-1, SL-2, SL-3”. When the desired level is obtained, momentarily
press any channel button to save the setting and return to the Timing Mode.
NOTE: To return to Timing Mode without saving, momentarily press the
Prince Castle logo button.
Restoring Factory Presets
Simultaneously pressing both the UP button, DOWN button and the Prince Castle
logo button during the first 6 seconds after applying power to the timer will
reset all channels back to their factory default settings.
Individual Channel Programming
NOTE: This mode can only be entered when all channels are idle.
Pressing and holding the Prince Castle logo button for 6 seconds will transfer
the unit into Channel Parameter Programming Mode. When programming mode is
first entered, the displays will show “Prog” until a channel is selected.
Momentarily pressing a channel’s button enables the parameter-programming mode
for that channel. After a channel has been selected, its associated display
will show and its timing cycle value, end of cycle label information and
action alarm time information will be displayed above or below it.
While in Channel Parameter Programming Mode, pressing the channel button next
to a parameter (timing value, end-of-cycle label or action alarm time) enables
the programming of that parameter for the selected channel. Use the UP and
DOWN buttons to modify the value of the enabled parameter. When either the
timing cycle value or action alarm time value are programmed, pressing the UP
button will increment the value and pressing the DOWN button will decrement
the value. Each time the UP or DOWN button is pressed the timing value
increments or decrements by one count.
NOTE: If either button is pressed and held, the timing value begins to
increment or decrement automatically with the change rate increasing the
longer the button is held.
When the parameters for the selected channel are set, pressing the Prince
Castle logo button will exit the channel’s Parameter Programming Mode and
return the unit to a state where another channel can be selected for
programming. When parameter changes for all channels have been completed,
press the Prince Castle logo button to exit Programming Mode and return the
unit to an operationally ready, idle state.
Exploded View
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>