Lorelli 1018003 Baby Bed Rail Safety Night Instruction Manual
- June 13, 2024
- lorelli
Table of Contents
Lorelli 1018003 Baby Bed Rail Safety Night Instruction Manual
Instruction
Scan the QR code to get more product information and manual instruction in
more languages. Download QR Scanner App onto your device.
WARNINGS BED SAFETY GUARD
- Never leave the child unattended!
- Make sure that the Baby Bed Rail is never placed close to an open fire or other strong source of heat, e.g. electric radiator, gas cooker.
- The bedguard is not recommended for use by children under the age of 18 months or when the child is over the age of 5 years.
- The bedguard should be used only when the child is able to climb in and out of the bed unaided.
- The bedguard should not be used as a substitute for a cot, as it cannot provide the same level of safety as a cot.
- The maximum thickness of the mattress for which the bedguard is suitable shall be 150 mm.
- The bed guard shall be fitted so that its side, when in the locked position or when placed in fitted position, touches the side of the mattress.
- The bed guard should not be used unless the fixings are in place and securely attached to the mattress.
- The bedguard should be checked to ensure that it is properly fitted and secure once fitted in place. 10. The bedguard should be periodically checked for its general condition with particular reference to the security of any locking mechanism or hinges used on the product.
- The bedguard should not be used on a sleeping surface that is more than 600 mm from the floor. when
- W ARNING: To prevent the risk of strangulation it is essential to ensure that the bed guard is fitted into position, there is a gap of at least 250 mm (10 in) between each end of the bed and the corresponding end of the bedguard.
- WARNING: Do not use additional and replacement parts other than those approved by the manufacturer or distributor.
CARE AND MAINTENANCE
- Please note the textile designation.
- Care for, clean and check this product regularly.
Parts
Picture 1
- Bag: – 1 pcs.
- Upholstery: – 1 pcs.
- Left and right base with belt: – 1 pcs
- Upper pipes of upholstery: – 2 pcs.
- Bottom pipes of upholstery: – 2 pcs.
Disruptions
-
Assemble the upper and lower upholstery pipes as shown in photos 2.
-
Insert the upper assembled pipes 4 into the upholstery opening from one end to the other as shown in picture 3.
-
Connect the pipe with the upholstery to the two pipes on the bases photo 4.
-
Pull both ends of the upholstery onto the tubes on the bases photo 5.
-
Insert the bottom tubes 5 into the bottom opening of the upholstery ( photo 6) and connect it to the opening of the base.
Place the baby bed rail on the bed so that the flat tubes on the base are
under the mattress The bed rail is ready for use photo 7. and make sure
that the bed rail is firmly in contact with the mattress. Position the rope
anchor so that it stands perpendicular to the back of the mattress and the
mattress frame. Tighten the fixed position with the buckle, which is close to
the anchor.
Folding of safety bed rail
To fold the bulkhead, simultaneously pull the buttons located at the bottom of
the two bases “3” and move the top of the bulkhead forward or backward photo
6. For storage, fold the two ends of the bed rail together photo 7.
ATTENTION! AFTER PUTTING THE BED RAIL IN A VERTICAL POSITION, MAKE SURE
THE LOCKING BUTTONS ON THE BASES ARE CLOSED (ACTIVATED), THE BELTS ARE
TIGHTENED AND THE MOVEMENT OF THE BED RAIL IS LIMITED! To disassemble the
bed rail, repeat all the steps in reverse order.
Unic importator in Romania DIDIS INTERNATIONAL
Strada Shantel Pantaloon Nr.1
Oars Pantaloon, Judetul Illovo Phone: +40 21 211 65 60
Fax: +40 21 210 65 62
E-mail: office@didis.ro
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>