MEAN WELL HLG-150H Series 150W Constant Voltage + Constant Current LED Driver User Manual

150W Constant Voltage + Constant Current LED Driver
HLG-150H series

HLG-150H Series 150W Constant Voltage + Constant Current LED Driver

http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf

Features

• Constant Voltage + Constant Current mode output
• Metal housing with class I design
• IP67/1P65 rating for indoor or outdoor installations
• Function options: output adjustable via potentiometer; 3 in 1 dimming
• Typical lifetime > 62000 hours
• 7 years warranty

Applications

• LED street lighting
• LED high-bay lighting
• Parking space lighting
• LED fishing lamp
• LED greenhouse lighting
• Type “HL” for use in Class I , Division 2 hazardous (Classified) location.

GTIN CODE

MW Search: https://www.meanwell.com/serviceGTIN.aspx

Description

HLG-150H series is a 150W AC/DC LED driver featuring the dual mode constant voltage and constant current output. HLG-150H operates from 90 ~ 305VAC and offers models with different rated voltage ranging between 12V and 54V. Thanks to the high efficiency up to 94%, with the fanless design, the entire series is able to operate for -40°C ~ +90°C case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. HLG-150H is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system.

Model Encoding

Stock
AB| IP65| lo and Vo adjustable through built-in potentiometer & 3 in 1 dimming function
(1-10Vdc, 10V PWM signal and resistance)| In Stock
D| IP67| Timer dimming function, contact MEAN WELL for details(safety pending).| By request

SPECIFICATION

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. Please refer to “DRIVING METHODS OF LED MODULE”.
5. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. (as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED driver can only be used behind a switch without permanently connected to the mains.
9. This series meets the typical life expectancy of >62,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80 or less. ℃
10. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com.
11. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).
12. For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE

※ This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs.

Typical output current normalized by rated current (%)

DIMMING OPERATION

※ 3 in 1 dimming function (for B/AB-Type)

• Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 1~ 10VDC, or 10V PWM signal or resistance.
• Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
• Dimming source current from power supply: 100A (typ.)

◎ Applying additive 1 ~ 10VDC
“DO NOT connect “DIM- to -V”| Dimming input: Additive voltage
---|---
◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):“DO NOT connect “DIM- to -V”| Duty cycle of additive 10V PWM signal dimming input
◎ Applying additive resistance:“DO NOT connect “DIM- to -V”| (N=driver quantity for synchronized dimming operation)
Dimming input: Additive resistance

Note: In the case of turning the lighting fixture down to 0% brightness, please refer to the configuration as follow, or please contact MEAN WELL for other options.

Using a switch and relay can turn ON/OFF the lighting fixture.

OUTPUT LOAD vs TEMPERATURE (Note. 10)

STATIC CHARACTERISTICS

※ De-rating is needed under low input voltage.

POWER FACTOR(PF) CHARACTERISTIC

※Tcase at 80℃

TOTAL HARMONIC DISTORTION (THD)

※ 48V Model, Tcase at 80℃

EFFICIENCY vs LOAD

HLG-150H series possess superior working efficiency that up to 94% can be reached in field applications.
※ 48V Model, Tcase at 80℃

LIFE TIME

MECHANICAL SPECIFICATION

Case No.954D
Unit:mm

※Blank/D-Type

※A-Type

※B-Type

※AB-Type

WATERPROOF CONNECTION

※ Waterproof connector
Waterproof connector can be assembled on the output cable of HLG-150H to operate in dry/wet/damp or outdoor environment.

2-PIN
12A/PIN
Order No.| M15-02
Suitable Current| 12A max.

※ Cable Joiner

◎ CJ04 cable joiner can be purchased independently for user’s own assembly.
MEAN WELL order No. : CJ04-1, CJ04-2.

※ Junction Box Option

INSTALLATION MANUAL
Please refer to: http://www.meanwell.com/manual.html

Downloaded from Arrow.com.
File Name: HLG-150H-SPEC 2024-02-06

References

• TÜV Rheinland - Home | US | TÜV Rheinland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>