DESAY SV AUTOMOTIVE M3GL06L Audio Carplay Screen Installation Guide

DESAY SV AUTOMOTIVE M3GL06L Audio Carplay Screen

Product Information

• Model: M3GL06L

Part 1: Function Block Diagram

Part 2: Statement

Category| Guaranteed storage| Guaranteed operation| Guaranteed performance| Nominal Non-destructive voltage range| Memory hold voltage| Temperature
---|---|---|---|---|---|---
Voltage| 40-85| 30-40| 20-65| N/A| N/A| N/A

• Part 3 : User’s Interface Overview

FCC statement

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

FCC Supplier’s Declaration of Conformity

• Product Name : CAR MULTIMEDIA
• Model number : M3GL06L; M3GL06R
• Suppliers Name : DESAY SV AUTOMOTIVE USA
• Suppliers Address (USA ): 840 W LONG LAKE RD STE 150, TROY MI 48098-6356
• Suppliers internet contact : Da.Xu@desaysv.com

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Product Usage Instructions

To use the Car Audio system, follow these instructions

1. Connect the DC power supply to the load using the 10P+6P Power/Speaker Connector.
2. Connect the SWRCS using the 28P STSW/VTR Connector.
3. Connect the GPS antenna using the 2P GPS Antenna.
4. Connect the DAB+ antenna using the 1P DAB+ Antenna.
5. Connect the radio antenna using the 5P Radio Antenna.
6. Connect the reverse camera controller using the 24P Rear Camera Connector.
7. Use the 19P HDMI Connector for HDMI transmission.
8. Connect USB devices using the 4P USB Adapter interface.

Please ensure that you follow the FCC guidelines provided in the user manual for proper operation and compliance with regulations. If you have any questions or need assistance, consult the dealer or an experienced radio/TV technician.

Part 1: Function Block Diagra

NO.

| ****

Name

| ****

Position

| ****

Function

---|---|---|---
1| 10P+6P Power/Speaker Connector| **** DA| Connect the DC power supply to the load
2| 28P STSW/VTR Connector| Connect the SWRCS
3| 2P GPS Antenna| Connect GPS antenna
4| 1P DAB+ Antenna| Connect DAB+ antenna
5| 5P Radio Antenna| Connect the radio antenna
6| 24P Rear Camera Connector| Connect the reverse camera controller
7| 19P HDMI Connector| HDMI transmission port
8| 4P USB Adapter| USB adapter interface

1. 10P+6P Power/Speaker Connector
2. 28P STSW/VTR Connector
3. 2P GPS Antenna
4. 1P DAB+ Antenna
5. 5P Radio Antenna
6. 24P Rear Camera Connector
7. 19P HDMI Connector
8. 4P USB Adapter

Part 2 Statement

1. 8.5~10.5）±0.5V ON-OFF
2. 9.0~10.5）±0.5V OFF-ON

Guaranteed performance| －20℃～65℃| （10.5V~16V）±0.5V
Nominal| NA| 12V±0.5V
Non-destructive voltage range| NA| （6V~24V）±0.5V
Memory hold voltage| NA| +B <4.5V: ≥ 50ms

+B >4.5V: ≥ 5s

Part 3 User’s Interface Overview

FCC statement
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

FCC Supplier’s Declaration of Conformity

• Product Name ：CAR MULTIMEDIA
• Model number ：M3GL06L; M3GL06R
• Suppliers Name : DESAY SV AUTOMOTIVE USA
• Suppliers Address (USA) ：840 W LONG LAKE RD STE 150, TROY MI 48098-6356
• Suppliers internet contact :Da.Xu@desaysv.com

FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>