Scudo S8 Momentum 1700mm Momentum Sliding Door and Side Panel Instruction Manual

Scudo S8 Momentum 1700mm Momentum Sliding Door and Side Panel

Product Specifications:

• Product Name: Momentum Sliding Door & Side Panel
  Enclosure

• Installation Date: 09/23

Product Usage Instructions

Before You Start:

It is crucial to follow the assembly instructions provided to ensure stability. Verify all fittings are included by checking accessory quantities upon opening the carton.

Tools and Materials Required:

• Level
• Screwdriver
• Silicone
• Tape Measure
• Pencil
• Soap
• Caulk Gun & Silicone
• Drill & Bits
• Rubber Mallet
• Handsaw

Tools & Materials Supplied:

Refer to the list provided in the manual. Additional tools and materials may be necessary based on site-specific requirements.

Installation Steps:

1. Saw off the wall-facing end as per Momentum Instructions.
2. Insert sliders into the designated cut-out area.
3. Ensure proper sealing with silicone, removing part 29 before sealing.
4. Level the shower tray in all directions and seal it to the wall.
5. The wall must be tiled down to the top edge of the tray without angling out the bottom tile.

Cleaning Instructions:

Routine Cleaning:

• Rinse transparent glass with warm and cold water, then dry with a squeegee.
• Clean glass with easy-clean treatment using diluted vinegar, rinse with clean water, and dry with a squeegee.
• Clean immediately after showering.

Main Cleaning:

Use water or vinegar for weekly or monthly cleaning based on user preferences.

Maintenance Tips:

Regularly lubricate bearings and hinged parts for optimal functionality. Tighten visible screws as needed for stability.

EASY-CLEAN COATING:

The special treatment on the glass prevents water droplets, soap dirt, or limescale from sticking, making cleaning effortless. Use non-abrasive cloths and cleaning agents for easy maintenance.

Frequently Asked Questions

Q: What should I do if some parts are missing from the supplied tools?

A: If any parts are missing, please contact customer support for assistance in acquiring the necessary components.

Q: How often should I perform main cleaning on the enclosure?

A: Main cleaning can be done weekly or monthly, depending on personal cleaning preferences and usage frequency.

BEFORE YOU START

IMPORTANT NOTICE
Please assemble according to our instructions, otherwise the enclosure will not be stable. Please check accessory quantities after you open the carton to ensure all fittings are included.

IMPORTANT NOTICE
Trat must be sealed fully around where the tray meets the wall. Tray must be 100% level in all directions. Ensure the shower tray is level in all directions and is properly sealed to the wall. The wll must be tiled down to the top edge of the
tray. Do not angle out bottom tile.

TOOLS AND MATERIALS REQUIRED

Needed

TOOLS & MATERIALS SUPPLIED

Note! Additional tools and materials may be necessary, depending on the specific requirements of the site.

MOMENTUM INSTRUCTIONS

IMPORTANT FOR PROPER CLEANING

Your shower enclosure is designed for minimum cleaning effort. In order to keep your shower enclosure permanently shining, a few rules must be observed.: Profiles and glass may only be cleaned with light cleaning agents. Abrasive cleaning agents, alcohol or nitric solutions must not be used. Do not use steel wool or course microfibre cloths for cleaning, as this will cause scratches. limescale in the water causes satins, so frequent cleaning is essential to keep your screen clean. The longer the limescale remains, the more difficult it is to remove.

MAINTENANCE OF MECHANICAL PARTS
The mechanical parts of the screen also need maintenance to ensure that they will function perfectly for many years to come. The bearings and hinged parts of the screen should be lightly lubricated. Screws that remain visible should also be tightened.

EASY-CLEAN COATING
The easy-clean coating is a special treatment that gives the glass an extra- smooth surface coating that prevents water droplets, soap dirt or limescale from adhering to the glass. Cleaning is not prevented, but all residues are easily and effortlessly removed. To clean the easy-clean coated glass surface, non-abrasive cloths and cleaning agent should be used.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>