SCUDO ALFIE-FL-OAK-600 Alfie Sonoma Oak 600 Wall Hung Vanity Unit and Basin Instructions

SCUDO ALFIE-FL-OAK-600 Alfie Sonoma Oak 600 Wall Hung Vanity Unit and

Basin Instructions

DOOR FITTING

1. Begin by opening the drawer and removing all items from inside. Pull back the dark grey cover clips on the support arm to reveal the thread.

2. Twist the support arms Anti-Clockwise to loosen the support from the door. Locate and remove the dark grey cover caps from the side of the drawer.

3. Using a posidrive screwdriver, insert screwdriver into the area shown above and twist 90o away from the door panel. This will now release the door panel.

4. Place the released drawer on the ground with the drawer clips facing up. Bend the clips 90o to release tension and remove.

5. Fitting a New Door
Keep the fitting clips from the previous door. Your new door may not come pre- drilled so you will have to:

• Use the previous door front to measure location of holes.
• Mark the new drawer front.
• Drill to 10mm deep.
• Insert clips and unfold to lock them in place.

Now repeat the previous steps in reverse to fit your new door.

UNIT MOUNTING

Mounting Bracket

Wall Hangers

1. Locate and insert the Mounting Bracket (if not already in place). Make sure the Hanger is facing the wall side as displayed in the second image. Once in position, lever down the Unit Lock to secure the Mounting Bracket as shown in the third image.

2. Measure the position for the wall hangers and screw into position. Place the Mounting Bracket hangers onto both the Wall Hangers as shown here (right).
3. Now tighten the Hanger first and then the red Clamp by turning both clockwise. Once both are tight, there should be no movement.
The adjustment screw can be used to lower or heighten the unit by 10mm.

DRAW ADJUSTMENT

Soft Close and Push Release Adjustment:
This can be adjusted by turning the orange wheel.
Notice the direction of the positive and negative rotation next to the wheel.

Important Information

• On receipt of any product, ensure that the product is unboxed carefully and inspected for damages or defects, within one day. In the unlikely event that the product is damaged please report this to retailer. Under no circumstance should the product be installed.
• Do not carry units by their struts/rails.
• Do not compress carcasses or other items up against walls as this may affect the door or draw opening action.
• Avoid the use of strong adhesive tapes, to prevent damage to the laminated surface.
• The manufacturer assumes that the product is being installed by a competent professional. We may ask for the evidence of this.
• The manufacturer assumes that the product is being installed on reasonable level floors and walls. If this is not the case, it is expected the product may not perform optimally.
• Steps must be taken to ensure the product is secured to a suitable surface, i.e. a stud with noggins placed for fixings.
• Glass Warning: Do not strike glass components with hard or pointed items. Do not place very hot or very cold items against or in close proximity to glass surfaces unless an adequately thick insulation material is used to prevent such items coming in contact with the glass. If a glass component becomes chipped or broken, replace immediately.
• Beware of hidden pipes and cables.
• Ensure appropriate PPE is warn.
• Never overload shelves or carcass.
• This furniture is designed for domestic environments only. These environments must be suitably ventilated using an extractor fan, of the appropriate size for the room, which has an overrun function.
• MDF or MFC based bathroom furniture must never be installed close to an unenclosed shower, or in a wetroom environment with any risk water will come into contact with the product.
• Any cut panel edges must be sealed with a good quality PVA, or silicone based sealant, especially the rear edge of any trimmed worktops or abutments to basins. Failure to do this will invalidate the guarantee.
• All points where worktops or furniture abut walls, floors or basins should be sealed with a bead of silicone to prevent capillary action causing water ingress into the units.
• Any and all spillages must be immediately cleaned and dried to prevent water ingress from occurring.
• Ensure any WC installed to the laminate is fully secured to the floor to prevent the WC from pulling up the veneer.
• Damage caused by water ingress will not be classified as a manufacturing defect as a combination of all the preventative measures, will result in the product lasting a lifetime.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>