E E ELEKTRONIK EE150 Humidity and Temperature Transmitter User Manual

: June 9, 2024
: E E ELEKTRONIK

Table of Contents

E E ELEKTRONIK EE150 Humidity and Temperature Transmitter
USER Manual
SCOPE OF SUPPLY
CONNECTION DIAGRAM
TECHNICAL DATA
Relative Humidity
Outputs
FCC
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

E E ELEKTRONIK EE150 Humidity and Temperature Transmitter

USER Manual

EE150 – Humidity and Temperature Sensor for HVAC applications
Find this document and further product information on our website at www.epluse.com/ee150.

SCOPE OF SUPPLY

EE150 sensor, type number according to order (for ordering guide see data sheet at www.epluse.com/ee150)
Cable gland M16 x 1.5
Mounting flange, PC, Ø 6.0mm (with Type T2)
Test report according to DIN EN 10204-2.2

CAUTION

For accurate measurement it is essential that the temperature of the probe and mainly of the sensing head is same as the temperature of the air to measure.
Avoid mounting the EE150 sensor in a way which creates temperature gradients along the probe. If possible, EE150 shall be installed with the entire probe inside the duct. For installation with mounting flange, in case of different temperature inside and outside the duct, the probe part outside the duct shall be thermally isolated.
The device and mainly the sensing head shall not be exposed to extreme mechanical stress.
Do not attempt to remove the filer cap, which is fixed. Avoid touching the sensing head at all times.
The stainless steel probe is ESD sensitive and shall be handled as such. Do not connect it to the ground potential.

CONNECTION DIAGRAM

E-E-ELEKTRONIK-EE150-Humidity-and-Temperature-Transmitter-
FIG-1

DIMENSIONS / MOUNTING Values in mm (inch)

E-E-ELEKTRONIK-EE150-Humidity-and-Temperature-Transmitter-
FIG-2

TECHNICAL DATA

Measurands

Relative Humidity

Working range 10…90 % RH
Accuracy at 20 °C ±3 % RH (30…70 % RH), otherwise ±5 % RH
Temperature dependency, typ. ±0.03 % RH/°C

Temperature

Working range -5…55 °C (23…131 °F)
T-Accuracy at 20 °C ±0.3 °C

Outputs

Analog output

0 – 10 V RL ≥ 10 kΩ
(0…100 % RH; T: see ordering guide) 4 – 20 mA (2-wire) RL ≤ 500 Ω

General

Power supply (Class III) (EU) / class 2 (NA)1)
for 0 – 10 V 15 – 35 V DC or 24 V AC ±20 %
for 4 – 20 mA 10 V + RL x 20 mA < UV < 35 V DC
Current consumption, typ. DC supply: 5 mA AC supply: 13 mArms
Connection Screw terminals, max. 1.5 mm2
Enclosure material Polycarbonate, UL94 V-0 approved
Protection rating IP65 / NEMA 4X
Cable gland M16 x 1.5 / UL94 V-2
Sensor protection PTFE filter, non-removable
Electromagnetic compatibility EN 61326-1 EN 61326-2-3 Industrial Environment FCC Part 15 Class B ICES-003 Class B
Working temperature range -5…55 °C (23…131 °F) 0…95 % RH, non-condensing
Storage temperature range -25…60 °C (-13…140 °F) 20…80 % RH

SETUP AND ADJUSTMENT

The EE150 is ready to use and does not require any configuration by the user. The factory setup of EE150 corresponds to the type number ordered. For ordering guide please see data sheet at www.epluse.com/ee150.
If needed, the user can change the factory setup by using the optional E+E Product Configuration Adapter (EE-PCA) and the E+E Product Configuration Software (EE-PCS). With these one can set the output scaling, and perform one or two point adjustment for humidity and temperature.
For product data sheet EE-PCA please see www.epluse.com.
The E+E Product Configuration Software (EE-PCS) is free and can be downloaded from www.epluse.com/configurator.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

INFORMATION

Langwiesen 7 • 4209 Engerwitzdorf • Austria Tel: +43 7235 605-0 • Fax: +43 7235 605-8
info@epluse.com • www.epluse.com LG Linz Fn 165761 t • VAT No ATU44043101 Place of Jurisdiction: 4020 Linz • DVR0962759 +43 7235 605 0 / info@epluse.com