FORUM LIGHTING SPA-38572-ACOP Rhom Recessed Downlight Instruction Manual

June 1, 2024
Forum Lighting

FORUM LIGHTING SPA-38572-ACOP Rhom Recessed Downlight

FORUM LIGHTING SPA-38572-ACOP Rhom Recessed Downlight

Warning

  1. Installation only to be carried out by qualified electrician
  2. Please ensure surface is suitable and capable of holding the luminaire and driver weight
  3. Pre-cut hole before installation, (see below chart for hole diameter)
  4. Do not operate if product is damaged
  5. IP65 rated front, suitable for bathroom zones 1 &2
  6. This product is suitable for fire rated installations, Part L Compliant of UK Building Regulations, Part B Compliant BS476 Parts 21 and 22

Dimension

Voltage: 220-240V AC
Lamp less: Built in LED
Wattage: 8W
Lumens: 900lm
Colour Temperature: 3000k/4000k/6000k
Cut Out: 70mm
Minimum Void: 70mm
Bezel Finish: Supplied with Antique Copper, Black Chrome, Chrome, Matt White,

Satin Black, Satin Brass, Satin Nickel
CRI:| >80Ra
Connection| Push on
Beam Angle:| 60º
Dimmable:| Dimmable with leading-edge trailing doge dimmer
Driver:| Non-Detachable

Dimension
Symbols

  1. This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical
    and safety regulations relevant to the country it is being installed.

  2. The product and its associated control gear are designed to operate on 220-240volts 50Hz.

  3. This downlighter range is designed to be installed in a ceiling tile/solid material with a minimum dimension of 3mm thickness.

  4. This product is for Indoor use only.

  5. Minimum Clearance is 70mm above the installed fitting, and no product should be installed within 50mm of any joist.

Specific Installation details

  1. Ensure the AC/mains power is not connected and cannot be reconnected during installation.

  2. For new installations use cutting tools suitable for the material and carefully cut the required hole to allow installation.(Figure 2)

  3. For refurbishment installations ensure that the existing hole is suitable and strong enough to hold the new downlight. Support the surrounding area if required.

  4. Connect the AC/mains cable to the driver using the marked terminals provided. Incoming Cable connections are,
    L=Live power conductor(brown), N= Neutral power conductor(blue). The driver offered is Class l.

  5. Remove downlighter from box and connect to the connector terminals via the connection system provided. (Fig.4)

  6. Raise the springs and place the downlight into the tile cut-out ensuring that both the driver and mains power cable are not trapped. (Fig.5)

  7. Once correctly connected, position the downlighter fully into the aperture so that the outer flange is flush with the installed ceiling tile/solid material. (Fig 6)

Specific Installation details

This product should be disposed of responsibly at the end of its life. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice (Waste Electrical and Electronic Equipment Directive)

Helpline
If you receive this item with parts broken or missing, please telephone: 0333 0050077
Please have ready your name, address, tel. no., product reference, where purchased and parts required. An answering service is in operation outside office hours and during busy periods.
We regret that we are unable to give advice on internal house wiring.

Cascade Holdings Ltd, Gorse Mill, Gorse Street, Chadderton, Oldham. OL9 9RJ
EU Authorised Representative: Authorised Rep Compliance,
Ground Floor, 71 Lower Baggot Street, Dublin, Ireland, O02P593.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Forum Lighting User Manuals

Related Manuals