VEVOR YY-F100-433 Restaurant Pager User Manual

: June 1, 2024
: VEVOR

Table of Contents

VEVOR YY-F100-433 Restaurant Pager
Basic Layout
Operating instructions
Simple Troubleshooting
Basic Parameters
FCC
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VEVOR-YY-F100-433-Restaurant-Pager-PRODUCT

Basic Layout

keyboard:

Extension Front:

Opposite:

Operating instructions

Setting keypad ID

Quickly press the DEL button several times within 3 seconds after plugging in the base and turning it on, and the screen will display a set of numbers (i.e. keypad ID).
Entering a new set of numbers on the keypad of the base.
After completing the input, briefly press the [CALL] button to exit.

Setting pager reminding duration:

Remove the pager from the charging base and remove its logo sticker.
Using a pointed item press the [Set] button briefly on the front of the pager several times to adjust the duration. The duration is as follows:
- (LED 1) On: 85.
- (LED 1 and LED 2) On: 16s.
- (LED 1, LED 2 and LED 3) On: 245.
- (LED 1, LED 2, LED 3 and LED 4) On: 32s.
- (LED 1, LED 2, LED 3, LED 4 and LED 5) On: 40s.

Seting and turning off the beep:

Removing the pager from the charging base and removing its logo sticker;
Using a pointed item to long press the [Set] button in the middle of the page several times until all (LED 1, LED 2, LED 3, LED 4, LED 5) lights are turned off. (note: Now the prompt time of the pager is 40 seconds).

Pairing pager number:

Remove the pager from the charging base and remove its logo sticker.
Using a pointed item to long press the [Set] button in the middle of the page several times until LED 2 and LED 3 light up.
Entering the desired number on the base and briefly press the [CALL] button
- (Note: After successful setting, the light will flash and there will be a beep reminder).

Using method:

Calling the pager:
- Remove the pager from the charging base and enter the desired number on the keypad, then press the[CALL]button.
Turning off the pager:
- Putting the pager back on the charging base, enter the number 99 on the keypad, and then press the [CALL] button.
- Note: Please turn off the pager when it is not being used to avoid affecting the battery’s life.

Simple Troubleshooting

No response from the pager when the keypad is calling:

Check if the calling number is correct.
The page number has been changed, it needs to be repaired with the keypad.
The pager is too far away from the base and the signal cannot be reached.

The pager screen goes black after showing it when the keypad is calling:

The battery level is too low and it needs to be charged for more than half an hour.
The battery is damaged and it needs to be replaced.

Basic Parameters

Product name YY -F100-433

FCC

FCC STATEMENT
This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA:
This device contains licence-exempt transmitters)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. For your safety, please read the user manual before using this product.