Dreamaker TDD193X91-DSC Fleece Top Multizone Electric Blanket Instruction Manual
- June 12, 2024
- Dreamaker
Table of Contents
- Dreamaker TDD193X91-DSC Fleece Top Multizone Electric Blanket
- Model Numbers
- Contents
- Connecting the Controller
- Securing Your Electric Blanket
- Using the Controller
- Overheat / Element Protection
- Recommended Cleaning Instructions
- CARE INSTRUCTIONS
- Servicing Your Blanket and Controller/s
- Storage
- Troubleshooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Dreamaker TDD193X91-DSC Fleece Top Multizone Electric Blanket
Model Numbers
- TDD193X91-DSC – Single
- TDD203X107-DSC – King Single
- TDD193X137-2DXC – Double
- TDD203X152-2DXC – Queen
- TDD203X182-2DSC – King
- TDD203X200-2DSC – Super King
Contents
- Important Safeguards
- Connecting the Controller
- Securing Your Electric Blanket
- Using the Controller
Thank you for purchasing our Zone Control Fleece Electric Blanket. Each unit is manufactured to ensure safety and reliability. Before using for the first time, please read the instruction manual carefully and keep it for future reference.
Important Safeguards:
Failure to observe these instructions will result in overheating. This will activate the overheat safeguard system, thus leaving the electric blanket inoperative. Misuse of this electric blanket will void your warranty.
Connecting the Controller:
- Turn off power and remove the plug from the power source.
- Ensure that the electric blanket is sized to suit your mattress.
- Do not use a single bed electric blanket on a double, queen, or king-size mattress.
- The electric blanket top must not hang over the edges of the mattress.
- Always turn off the power and unplug the electric blanket from the power source before removing or fitting the controller/s.
- Before removing the controller, make sure the controller is turned off.
Securing Your Electric Blanket:
- Your electric blanket must be placed directly onto the mattress. If using a mattress protector, it goes over the electric blanket.
- Do not use a waterproof mattress protector under or over the electric blanket.
- Electric blankets must not be used on top of the user; instead, they must be firmly secured to the mattress.
- Failure to follow these fitting instructions may trigger the overheat protection system and render the electric blanket permanently inoperative. This may void the warranty.
- Care should also be taken if using a continental quilt because heat will build up more quickly than with other bed coverings. A short period may only be needed to reach maximum temperature depending on the insulation density of your quilt. This also applies if using additional bed blankets.
Using the Controller
- Refer to the specific instructions provided with the detachable 11-hour auto-off controller for detailed usage information.
IMPORTANT INSTRUCTIONS:
Retain this manual and receipt for future use. Keep electric blanket in
original packaging. (Please complete warranty form on the back page)
Thank you for purchasing our Electric Blanket. Each unit is manufactured to ensure safety and reliability. Before using for the fi rst time, please read the instruction manual carefully and keep it for future reference.
IMPORTANT SAFEGUARDS
- This electric blanket is for domestic use only. It is not intended for use in hospitals or the like.
- Before connecting and switching on the electric blanket, ensure that the voltage indicated on the rating label corresponds to the mains voltage in your home.
- Do not plug into a powerboard, double adaptor or the like. The power plug must be inserted directly into the wall power socket.
- Read the instructions carefully, in conjunction with the illustrations, before fi tting the electric blanket and using for the fi rst time.
- If the cord of this electric blanket is damaged, unplug and discontinue use of the product then contact the manufacturer.
- Check daily that your electric blanket is fl at, fully spread out and secured before switching it on.
- Only use the controllers supplied with this electric blanket.
- Failure to observe these instructions will result in overheating. This will activate the overheat safeguard system, thus leaving the electric blanket inoperative. Misuse of this electric blanket will void your warranty.
- Use as an underblanket only.
- These electric blankets are not recommended for futons.
- The electric blanket should not be used on an adjustable bed as the electric blanket and/or cord may get caught in the bed and creased.
- It is recommended to check with the manufacturer of memory foam mattress before using this electric blanket.
- This electric blanket should not be used over or under a water bed or a waterproof mattress protector.
- The electric blanket is not to be used by children under the age of three.
- This electric blanket is not intended for use by young children or infi rm persons without adequate supervision.
- Persons prone to bed-wetting should not use this electric blanket.
- Children over the age of three must be supervised by an adult while in operation at all times
- This electric blanket is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- This electric blanket must not be used by persons insensitive to heat and other very vulnerable persons who are unable to react to overheating.
- Prolonged application at the higher heat setting can result in skin burns.
- It is recommended that persons with artifi cial pacemaker should check with their doctor and the manufacturer of the pacemaker before using this electric blanket.
- Electric blankets are intended for human use only. Not for animals and pets.
- Do not allow pets or animals to lie or chew on this product or on the electrical cords etc.
- Make sure that the heating area (on any side of the bed) does not fall over the edge of the mattress, that the attachments are adequate and suited to the mattress, and that the instructions are read before using the electric blanket.
- Do not insert pins into any area of the electric blanket as these may damage the electric wiring.
- Do not tuck the edges of the electric blanket in.
- Do not use the electric blanket rucked (creased) or folded.
WARNING:
DO NOT switch the power on if the electric blanket is wet or in a folded or
creased state. The electric blanket needs to be unfolded and laid fl at before
switching on.
- Keep the controller/s away from an open window.
- Keep the controller/s away from external heat sources. i.e. a heater, fi replace etc.
- Be sure that this electric blanket is used only on an alternating current supply circuit of the correct voltage. Refer to the rating label for specifi cations (foot end of the electric blanket).
- The fl exible supply cord and switch must, as far as practicable, be kept outside of the bed covers.
- Arrange the electric blanket so that the elements are not under the pillows and/or bolsters.
- Bed clothes should not be folded back when the electric blanket is switched on.
- Do not leave heavy objects on the bed, e.g. folded blankets, suitcases etc. when the electric blanket is switched on as this will trigger the over temperature device and render the electric blanket PERMANENTLY inoperable. This may also void the warranty.
- Switch off at the power outlet and remove the plug from the mains when the electric blanket is not in use.
- When storing the electric blanket, allow it to cool down or dry completely before folding. Fold neatly but not tightly (or rolled) without sharp bends in the heating elements and store where no other heavy objects will be placed upon it.
- The controlller/s should be stored unplugged from the electric blanket.
- Do not dry-clean this electric blanket. Cleaning liquid may have a damaging eff ect on the insulation covering of the heating element. Follow washing directions located on the electric blankets rating label (foot end of the electric blanket) and in this instruction manual.
- If any abnormality or defect in operation is observed, discontinue its use immediately and consult the distributor regarding its examination and/or repair.
- The electric blanket should be examined frequently for signs of wear, either of the electric blanket, controller or fl exible cord. If wear is visible or if any abnormality or defect in operation in the electric blanket is observed, discontinue use immediately and consult a qualifi ed and registered person for service.
- It is recommended that your electric blanket is inspected by a qualifi ed and registered person after 3 years of use.
- Depending on the controller type, you may notice a blue fl ash in the switch when moving from one setting to another. This is NOT dangerous and is caused by the copper parts making contact.
- For additional protection, it is strongly recommend that the use of a residual current device (RCD) with a tripping current not exceeding 30mA be used on the circuit supplying this product. If you are unsure if your home has this device, please contact your nearest electrical contractor.
- Always treat electrical appliances with the upmost care. Do not use this product in any other fashion or for any other purpose other than stated in these instructions.
WARNING:
DO NOT use an electric blanket if it or the bedding material has been
soiled with oil. This includes physiotherapy, massage and cooking oils. Oil-
affected items can ignite spontaneously, especially when exposed to heat
sources such as an electric blanket. The items become warm, causing an
oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fi re.
Connecting the Controller
Turn off Power and Remove the Plug from Power Source
- To fi t the controller plug, simply hold the socket with one hand and push the controller plug all the way until it’s fi rmly in place.
- To remove the controller, lift the locking tab up with your fi nger and pull the plug directly out. Do not pull the controller cable and do not try and pull the controller plug out without lifting the locking tab as you will damage the socket.
- Do not fold, roll or kink the cable. Allow the cable to hang freely.
- Ensure the cable is not pulled so tight that it bends hard at the electric blanket connector end.
- NOTE: Ensure that the electric blanket is sized to suit your mattress i.e. queen sized electric blanket must be used on a queen sized mattress.
- Do not use a single bed electric blanket on a double, queen or king size mattress. The electric blanket top must not hang over the edges of the mattress.
WARNING:
Always turn off the power and unplug the electric blanket from power source
before removing or fi tting the controller/s. Before removing the controller,
make sure the controller is turned OFF.
Securing Your Electric Blanket
Note: Your electric blanket must be placed directly onto the mattress. If using a mattress protector, this goes over the electric blanket. DO NOT use a waterproof mattress protector under or over the electric blanket.
IMPORTANT:
- Place the electric blanket onto the mattress with the controller connection/s at the HEAD END of the bed.
- NOTE: Electric blankets MUST NOT be used on top of the user (as with a normal blanket), instead they must be fi rmly secured to the mattress.
- Fit the side skirts around the edges of the mattress then use the elastic skirt to ensure that the electric blanket fi ts snugly around the sides and underneath the mattress.
- Spread the skirt around the mattress edge ensuring even tension and making sure the electric blanket is placed evenly over the mattress then ensure that the electric blanket is fl at and crease free.
- FAILURE TO FOLLOW THESE FITTING INSTRUCTIONS MAY TRIGGER THE OVERHEAT PROTECTION SYSTEM AND RENDER THE ELECTRIC BLANKET PERMANENTLY INOPERATIVE. THIS MAY VOID THE WARRANTY.
- Note: Care should also be taken if you are using a continental quilt because heat will build up more quickly than with other bed coverings. A short period may only be needed to reach maximum temperature depending on the insulation density of your quilt.
- This also applies if using additional bed blankets.
- The electric blanket should not be tucked in at the sides.
- Make your bed in the usual manner.
- After the electric blanket is secure and fi tted correctly, plug the controller/s into the wall power socket and turn on.
IMPORTANT: DO NOT COVER THE CONTROLLERS AT ANY TIME. Keep the controller away from external heat sources. i.e. a heater, fi replace etc.
Using the Controller
- Use your Electric Blanket with Detachable Controller Model PS4X2G-11 only.
- Do not use any other controller for this blanket.
To turn on the controller, slide the switch on the side of the controller to ON. By default, when you fi rst turn on the controller, the timer will be set at zero with no heat indicator lights. This means the power is on. This electric blanket has two separate heating zones ‘Body’ zone and ‘Foot’ zone, the controller can separately control the body zone and foot zone. You are able to independently heat just your feet or body or both together. Body zone has 4 heat settings, ‘Foot’ zone has 4 heat settings. These are indicated on your controller by yellow lights for ‘Body’ and red lights for ‘Foot’. To set the desired heat level, press Body’ or ‘Foot’ button. When you press ‘Body’ or ‘Foot’ button for the fi rst time, the default heat level is at one and the timer is at 8. Each press of the ‘Body’ or ‘Foot’ button, will advance to the next heat level. 4 full lights, either red or yellow, means the heat level is at its highest. Press the Body’ or ‘Foot’ button continuously to reset heat level to zero (no heat indicator lights). The timer will automatically reset to zero. To set the timer, press ‘Time’ button to cycle through 1-9 & 11 hours. The electric blanket will operate until the selected time runs out. The controller will return to the default ‘power on’ setting. Select 4 lights (yellow or red) for preheating 30-60 minutes before using. When heat level is at its highest (4 red or yellow lights), after 3 hours, it will automatically drop to the next level (3 red or yellow lights). If you will go to sleep or use it for a long time, please set at the lowest heat level. Do Not sleep overnight with full heat settings on.
WARNING:
The highest temperature setting is for preheating only and not recommended for
continuous operation. TURN OFF AND UNPLUG THE ELECTRIC BLANKET WHEN NOT IN
USE. Keep the controller away from external heat sources. i.e. a heater,
fireplace etc. Never leave an electrical appliance unattended when switched
on. Page 8 of 16
Electrical Field Eff ect
When using the electric blanket, some people may be susceptible to a tingling
sensation when alone or when touching someone else using the blanket. This
“tingling” feeling is known as an “electric field effect” and is occasionally
known to happen across all makes and brands of Blankets. It is caused by the
current flowing through the element creating an Electromagnetic Field (EMF).
Some people are more susceptible to feeling this EMF tingling sensation than
others. This is no cause for concern and is in no way an electric shock.
Auto Off
This controller is fi tted with a 11 hour Count Down Auto Off Timer which
starts to countdown from when your heat setting has been selected, and will
switch power off to the elements after approximately 11 hours. (+/- 30
minutes). The blanket can be set to 1, 2, 3, 4, 5, 6, 7, 8, 9 and 11 hours
only.
Note: Once a heat setting has been selected and the switch is powered ON, the countdown timer will not be aff ected by adjusting heat level. The timer can be rest by pressing the Time button or after being powered OFF and then back ON.
Pre Heat
The controller has a pre-heat facility in order for you to warm your bed prior
to getting into it. The time taken to pre-heat the bed will depend on the
ambient temperature of the bedroom and whether an electric blanket has been
used to air the bed on a regular basis. At normal ambient temperature you
should allow approximately 30 – 60 minutes on Heat Setting “4” (Pre Heat).
This is displayed by either 4 red lights for feet or 4 yellow lights for Body.
You are able to Pre heat both sections of the Blanket, Feet and Body at the
same time. You may get into bed sooner while the bed is still warming up, but
please DO NOT leave the electric blanket set on the Preheat setting (No. 4)
while you are in the bed. A cold room or bed that has not been used for some
time may require a greater length of time on the pre-heat.
Overheat / Element Protection
- The blanket is fi tted with numerous overheat safeguard systems. This off ers protection against overheating or damage to the elements by disengaging the power to the elements before overheating hazards occur.
- Should there ever be a problem with the heating element in the blanket, it will automatically close down the operation and the Blanket will turn off.
- The controller must not be covered. The controller has built in protection, so that if the controller overheats. or the heating element is damaged, it will automatically close down the operation permanently.
- If the 4 temperature yellow / red LED indicator lights are all fl ashing, please check whether the coupler of the electric blanket has been connected fi rmly or not and restart it. If the fault cannot be removed, it means the internal connection of the electric blanket has problems or short circuiting. Please contact after-sales service.
NOTE: Keep the controller away from external heat sources. i.e. a heater, fireplace etc. Please refer to the Troubleshooting Guide on page 14 of this manual before calling the service department or before returning the Blanket.
Recommended Cleaning Instructions
DO NOT DRY CLEAN, DO NOT WRING, DO NOT SPIN DRY. Ensure all controllers are unplugged from the power point and from the electric blanket before cleaning. Ensure the controller/s and plugs do not get wet.
CARE INSTRUCTIONS
- DO use only as an underblanket.
- DO secure blanket to bed property before use.
- DO only clean the blanket as specified in the instruction book.
- DO have this blanket repaired and/or tested by an authorised electrical agent.
- DO turn off and unplug when not in use.
- DO remove controller before washing blanket.
- DO Warm machine wash separately with maximum temperature 40ºC mild process. DO Line dry in shade when excess water has been removed.
- DO NOT use as an over blanket.
- DO NOT use tucked in, folded, rucked, bunched up or creased.
- DO NOT use with element or wired parts tucked in.
- DO NOT use electric blanket or the bedding material if soiled with oil. This includes
- physiotherapy, massage and cooking oils.
- DO NOT use if wet.
- DO NOT insert needles or pins into blanket.
- DO NOT use with damaged element or cables.
- NOT TO be used by persons insensitive to heat and other very vulnerable persons who are unable to react to overheating.
- NOT TO be used by very young children.
- DO NOT cover controller.
- DO NOT bleach/tumble dry/spin dry/dry clean.
- DO NOT peg wired parts/wring/iron.
Treatment for Localised Soiling
Never Use Hot Water as the electric blanket may shrink and will void your
warranty. The area aff ected should be sponged gently using a natural wool
detergent or mild soap fl akes dissolved in lukewarm water (30°C Max),
followed by two consecutive sponging using clean, soap-free lukewarm water.
- Lightly compress the treated area between two towels to absorb excess water.
- Do Not Wring or Spin Dry the Electric Blanket.
- Refer to the section “Drying” for drying instructions.
- The connections to the electric blanket must be kept free of moisture..
Hand Washing (Recommended)
Never Use Hot Water as the electric blanket may shrink and will void your
warranty.
- Place the electric blanket in lukewarm (30°C Max) water (bathtub or large laundry tub is ideal) mixed with either a natural wool detergent or with mild soap fl akes.
- Do not bleach or use fabric softener.
- Soak the electric blanket for approximately fi ve minutes, and then gently squeeze the soapy water through.
- Rinse the electric blanket thoroughly with clean lukewarm water until no more suds are visible and allow water to drain off.
- Refer to the section “Drying” for drying instructions.
- With normal use it is recommended you hand wash your electric blanket once a year. Do Not Wring or Spin Dry the Electric Blanket.
Machine Washing
- Place the electric blanket in the washing machine with either a natural wool detergent or with mild soap fl akes.
- Do not bleach or use fabric softener.
- Set your machine to the Delicate Wool or Gentle cycle (without Spin Dry) and set the water temperature to warm (30°C Max). Do Not Wash With HOT Water.
- When the cycle has fi nished, allow water to drain off.
- Refer to the section “Drying” for drying instructions.
- Do Not Wring the Electric Blanket. Do Not Spin Dry.
Drying
- Spread the blanket out on a clean surface (e.g. a large table) to dry in a shady area.
- Your blanket can also be dried on a clothes line provided the blanket is not creased or folded.
- Ensure pegs are not used on the element areas of the blanket if hanging on the line. Note: The blanket must be thoroughly dried including controller sockets before being re-fi tted to your bed.
- With normal use it is recommended you hand wash your blanket once a year.
Servicing Your Blanket and Controller/s
NOTE: There are no user serviceable parts in this electric blanket or controller/s.
- The electric blanket should be examined frequently for signs of wear, either of the electric blanket, controller or fl exible cord. If wear is visible or if any abnormality or defect in operation in the electric blanket is observed, discontinue use immediately and consult a qualifi ed and registered person for service.
- It is recommended that your electric blanket is inspected by a qualifi ed and registered person after 3 years of use.
- If the electric blanket is not operating correctly, please check the Troubleshooting Guide on page 14 of this manual before contacting our service department.
Storage
When storing the electric blanket, allow it to cool down or dry completely before folding. Fold neatly (or rolled) but not tightly without sharp bends in the heating elements and store where no other heavy objects will be placed upon it. The controller/s should be stored unplugged from the electric blanket. Store in a dry place, where the electric blanket cannot be damaged and is not prone to collecting dust and lint.
Troubleshooting
Testing Controllers
Before contacting the service department please follow the steps below to determine if there is actually a fault, and if so, if a fault is within the blanket or within the controller. This will make it easier when talking to the service department. Please also refer to the Troubleshooting Table on the next page for additional information prior to contacting the service department.
- Remove the “good” controller, which you know functions correctly from the other side of the blanket (excluding all single size blankets as these only have the one controller), and test it on the “trouble side” of the blanket to determine if it is the original controller or the blanket element which is at fault.
- Please allow the “good” controller to be tested overnight as it may take a few hours for any fault to show up. It is possible that the “good” controller may function for a few hours prior to failing so it is important that the test be performed overnight and not just for a few minutes.
- If after the overnight test, the controller is still functioning (i.e. the lights on the front display are showing) and the blanket is heating properly, it can be concluded that the original controller is faulty.
- If this is the case, please call the service department for a replacement controller. The model number of the controller is moulded into the back of the controller.
- If the “good” controller, when tested on the ‘Trouble Side” of the blanket is found to be still functioning properly (i.e. the lights on the front display are showing) after the overnight test, but the blanket is not heating, it can be concluded that the blanket element is faulty.
If this is the case, and if the blanket is still within the warranty period, please return the blanket to the retailer. If returning the blanket, we please ask that:
- The unit is packed carefully back into its original packaging.
- Original proof of purchase is attached.
- A brief note attached to the blanket explaining the reason why it is being returned.
Troubleshooting Table
Problem | Cause | Remedy |
---|
No power to controller / No heat level indicator lights showing on front display
| The temperature switch is in the “OFF’ position| Please switch on controller
to “ON” position.
The power plug may not be plugged in to the power source and switched on.|
Ensure the power plug is inserted into the power source correctly and switch
on.
There may be no power to the power point
| Ensure there is power to the power point. Test with another appliance such as a table lamp.
Flashing lights on controller display
| The controller has overheated and blown the Over-Temp thermal fuse.| The
controller has overheated by means of an external heat source or the electric
blanket elements have been damaged. A new electric blanket with controller
must be purchased.
The electric blanket elements have been damaged.
Heat level indicator lights showing on front display but electric blanket is not
heating
| Detachable plug from controller to electric blanket is not fitted correctly
or has come loose.| Ensure the detachable plug is fitted correctly into the
socket on the electric blanket and the locking tab has clipped over the lug on
the plug.
The selected heat setting is too low.| Increase the heat setting.
Bed covers not pulled up over electric blanket.
| The electric blanket must be covered with the bed clothes / doona. The electric blanket will not feel warm if not covered while heating up.
Do Not Cover the Controllers.
Pre-heat time is too short.
| Allow the electric blanket more time to heat up.
More time is required depending on the ambient temperature.
Heat level indicator lights showing on front display but cannot change any of the settings| ****
Program may have locked up to protect itself due to a power surge.
| ****
Unplug the controller from the power point, wait 2 minutes and then plug in and switch on again.
Heat level indicator lights flashing on front display| ****
This is normal.
| The electric blanket controller will automatically turn off after approximately 11 hours. Slide the button to the “Off” position to reset, wait 5 seconds, then select the desired heat setting again.
Controller is warm to touch
| This is normal. The elements run inside the tube from the electric blanket to the controller and will get warm when in operation.| ****
Nothing to do. It is no cause for alarm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>