acer K272HL Monitor Lifecycle Extension User Guide

**acer K272HL Monitor Lifecycle Extension User Guide

**

Important Safety Notice

Product Announcement:

This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. Vender assumes no liability express or implied, arising out of any unauthorized modification of design or replacing non-RoHS parts. Service providers assume all liability

Qualified Repairability:

Proper service and repair is important to the safe, reliable operation of all series products. The service providers recommended by vender should being aware of notices listed in this service manual in order to minimize the risk of personal injury when perform service procedures. Furthermore, the possible existed improper repairing method may damage equipment or products. It is recommended that service engineers should have repairing knowledge, experience, as well as appropriate product training per new model before performing the service procedures.

NOTICE:

• To avoid electrical shocks, the products should be connect to an authorized power cord, and turn off the master power switch each time before removing the AC power cord.
• To prevent the product away from water or explosed in extremely high humility environment.
•  To ensure the continued reliability of this product, use only original manufacturer’s specified parts.
• To ensure following safety repairing behavior, put the replaced part on the components side of PWBA, not solder side.
• To ensure using a proper screwdriver, follow the torque and force listed in assembly and disassembly procedures to screw and unscrew screws.
• Using Lead-Free solder to well mounted the parts.
• The fusion point of Lead-Free solder requested in the degree of 220°C.

Exploded Diagram

**Product Exploded Diagram

**

INDEX

|

DESCRIPTION

---|---

1

| MID-FRAME

2

|

PCBA CTRL BD

3

|

LCDM 27W AUO M270HVN02.3Q0 Z

4

|

PCBA SPS BD

5

| PCBA IF BD

6

|

FFC LVDS 30P P1 B276HL

7

| ASSY SHD AH1 1A1D1H+SPK V276HL

8

| #SPK*2 2.5W 4OHM 320/320MM

9

| ASSY RC 1A1D1H+SPK DB22A V276H

10

| ASSY CLMN K272HL

11

|

ASSY BASE K272HL

12|

ASSY TRIM K272HL

Wiring connectivity diagram

There are four types of wiring diagrams for model K272HL. The wiring connectivity position will be different according to the ACTUAL PCBA connector position. Please base on different SKU refer to below diagram.

NOTE : INF BD= Interface Board, PWR BD=Power Board, CTRL BD= Control Board

1. SKU with USB
   

2. . SKU without USB
   

Mechanical Instruction

Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.

Tool Description:

• working table
• Screw-driver: Philips-head screwdriver, Hex-head screwdriver
• Knife
• glove
• cleaning cloth
• ESD protection

Disassembly and Assembly SOP

K272HL

Disassembly Procedures

Preparation before disassemble

1. Clean the room for disassemble
2. Identify the area for monitor
3. Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow; according to the actual condition plan the disassemble layout
4. Prepare the implement, equipment, materials as bellow:
5. working table
6. Screw-driver: Philips-head screwdriver, Hex-head screwdriver
7. knife
8. glove
9. cleaning cloth
10. ESD protection

After unplugging the power cord, the power board still have power energe. Please pay attention when disassembling/assembling Power BD.

S1
Disassemble the RC(Rear Case), stand and base **| Before Disassembling & Assembling, monitor need to be put on the sponge and the Insulation glove must be wore during the process.
Disassemble Stand and Base from the RC(Rear Case). Unlock RC screws. Disassemble RC from monitor.
S2
Disassemble SHD and MF**| Tear down AL-Tape off SHD(Shielding) as picture 1.
Unlock the Hexagonal screws as picture 2.
Unlock 9 MF screws and 2 trim screws as picture 3.

S3
Disassemble the lamp wire| Tear off the tape on the lamp wire and etract the lamp wire form the P/BD(Power Board) as the picture

S4
Disassemble LVDS cable and CTRL BD| Tear off the tape, pull out the FFC as picture 1. Pull the CTRL BD-FFC out of the PCBA and the CTRL BD, tear off the tape and disassemble the CTRL BD-FFC

S5
Disassemble the Bezel from panel.| Tear off the tapes, take out the Panel and the CTRL BD of the Bezel
S6
Disassemble I/F BD and P/BD from SHD.| Disassembled the Mylar and unlock all screws.
Disassemble the I/F BD from the SHD and extract the P/BD wire. Extract the FFC LVDS from the I/F BD.
Disassemble the P/BD from the SHD.

NOTE: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.

Assembly Procedures

Preparation before disassemble

1. Clean the room for disassemble
2. Identify the area for monitor
3. Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow; according to the actual condition plan the disassemble layout
4. Prepare the implement, equipment, materials as bellow:
5. working table
6. Screw-driver: Philips-head screwdriver, Hex-head screwdriver
7. knife
8. glove
9. cleaning cloth
10. ESD protection

After unplugging the power cord, the power board still have power energe. Please pay attention when disassembling/assembling Power BD.

S1
Assemble I/F BD and P **| Before Disassembling & Assembling, monitor need to be put on the sponge and the Insulation glove must be wore during the process.
**Insert the FFC to the I/F.
Insert the P/BD-Wire to the I/F BD and the P/BD.
Place the I/F BD and the Power BD to main SHD.
stick one tape on the SHD remarked with red circle and lock all screws as the picture. Put Mylar on the Power BD

S2
Assemble MF and Panel| ake the Panel and insert lamp wire to panel Assemble the MF to the panel ,and lock 9 screws to the MF as the picture
PICTURE 1

S3
Assemble SHD| Lock the Hexagonal screws as picture 1. Use jig to put the SHD in correct position on Panel. Take off the jig and stick two AL tapes as picture 2
PICTURE 1

**PICTURE 2

Note: please refer to Appendix for the jig and select “None” for page scaling item


S4
Assemble LVDS cable| Insert the LVDS cable to the Panel and stick one tape on LVDS cable
S5
Assemble the lamp wire| Insert the lamp wire to the P/BD . Stick 2 tape to fasten the lamp wire and one AL-Tape on SHD as the picture.
S6
Assemble CTRL-BD| Insert the CTRL BD-FFC to CTRL BD as circle frame, and insert them into the bezel. Assemble the panel on the bezel. Stick Mylar on CTRL BD FFC as square frame and Insert the CTRL BD -FFC to the PCBA as circle frame.
S7
Assemble RC, stand and base| Assemble the RC with screw. Assembly the Stand and the Base to Monitor
PICTURE 1

PICTURE 2
PICTURE 3

NOTE** : Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.

Troubleshooting

TROUBLESHOOTING

Before sending your LCD monitor for servicing, please check the trouble- shooting list below to see if you can self-diagnose the problem.

(VGA Mode)

Problems

| Curren! Slays|

Remedy

---|---|---

No Picture

| LEO ON|

• U sing 050. adjust b6glaneta and contrast to maximum or reset to their bead setbnge.

LEO OFF|

• Check the gam rant

• Clock II AC pas cad is properly connected to the manna.

LED displays amber cola|

• Check II Sao signal title is properly connected at me took of mond.

• Check II me paver of camas system is ON.

Abnormal Picture

| Unstable picture|

• Check if the specification of graphics adapter and monitor is in compliance which may be causing the input signal frequency mismatch.

Display is missing,
center shift, or too
small or too large in display size|

• Using OSD, adjust RESOLUTION, CLOCK, CLOCK-PHASE, H-POSITI

• Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing.

• Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing.

• Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or powering OFF the monitor.

Abnormal Sound (Only Audio-Input model) (Optional)

| No sound, or sound
level is too low| Check the audio cable with the host PC is connected.
Check if the volume setup of the host PC is in minimum position and try to raise the volume level

(HDMI/DP Mode)

• Using OSD, adjust brightness and contrast to maximum or reset to their default settings.

LED OFF|

• Check the power switch

• Check if AC power cord is properly connected to the monitor.

LED displays amber color|

• Check if AC power cord is properly connected to the monitor

• Check if the power of computer system is ON.

Abnormal
Sound (Only Audio-Input model) (Optional)| No sound, or sound level is too low| Check the audio cable with the host PC is connected.
Check if the volume setup of the host PC is in minimum position and try to raise the volume level.

FRU List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of ACER K272HL. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

Please note that WHEN ORDERING FRU PARTS, you should c heck the most up-to- date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For AUTHORIZED SERVICE PROVIDERS, your office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional office to order FRU parts for repair and service of customer machines

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional office on how to return it.

BOARD
| MAIN BD| PCBA IF BD MI VA270H AUO H+S| 55.T5UM3.001
| POWER BD| PCBA SPS BD MI H+S V276HL AUO| 55.T5UM3.002
| CONTROL BOARD| PCBA CTRL BD SMD B276HL| 55.T4HM3.003

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>