AFX CLMB36LAJENSN LED Indoor Luminaires Wall Mount Light Instruction Manual

AFX CLMB36LAJENSN LED Indoor Luminaires Wall Mount Light

Product Information

Specifications

• Model Numbers: CLMB36LAJENxx, CLMB48LAJENxx
• Product Type: LED Indoor Luminaires
• Warranty: 5-year limited factory warranty

Product Usage Instructions

Safety Precautions
Before starting the installation process, make sure to follow these safety precautions:

1. Disconnect electrical power at the fuse or circuit breaker box.
2. Handle the fixture and hardware kit carefully.

Assembly Instructions

1. Remove the fixture and hardware kit from the carton.
2. Remove components from the hardware kit.
3. Install the mounting bracket to the junction box using provided screws.
4. Mark mounting locations on the wall and secure the bracket accordingly.

Wiring Instructions

1. Make wire connections following the color-coding:
   • Green wire from fixture to ground wire.
   • White wire from fixture to white (N) wire from power source.
   • Black wire from fixture to black (L) wire from power source.
2. Ensure secure connections and tuck wires neatly into the junction box.

Switch Operations
The pull switches on the fixture operate different lights:

• Right pull switch:
  • Pull once: Turns on uplight.
  • Pull twice: Turns on downlight.
  • Third pull: Turns on both uplight and downlight.
  • Fourth pull: Turns off both lights.
• Left pull switch:
  • Pull once: Turns on night light.
  • Pull twice: Turns off night light.

FAQ

Q: What is the warranty coverage for this product?
A: The product comes with a 5-year limited factory warranty that covers defects in materials and workmanship under normal operating conditions. It does not cover failure due to improper installation, misuse, mishandling, or damage during transit.

LED Indoor Luminaires Wall Mount – Over Bed 120VAC / 60Hz

Model #: CLMB36LAJENxx
CLMB48LAJENxx

Safety Precautions

• Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in potentially fatal electric shock and/or property damage.

• It is recommended that a qualified electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.

• Do not handle any energized fixture or attempt to energize any fixture with wet hands or while standing on a wet or damp surface or in water.

• This fixture is designed for use in a 120VAC / 60Hz circuit. This fixture is not compatible with dimming circuit.

• Make sure that the power source conforms to the requirements of the fixture. (See labels on the fixture housing).

• To reduce the risk of electrical shock, and to assure proper operation, this fixture must be adequately grounded. To accomplish proper grounding, there must be a separate ground wire (green) contact between this fixture and the ground connection of your main power supply panel.

• This fixture is intended to be used for general indoor lighting in dry or damp locations.

• Disclaimer
  Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiver antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult with the dealer or an experienced radio/TV technician for help.

• Any modifications to this fixture may void the warranty and interfere with the safe operation of the luminaire.

Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Assembly Instructions

Step 1 – Preparing for installation

1. Disconnect electrical power at the fuse or circuit breaker box before installing or servicing any part of this fixture.
2. Carefully remove the fixture and hardware kit from the carton.
3. Remove components from the hardware kit.
4. Remove mounting bracket (1) from the fixture (3) by removing four side screws (4).
5. Install mounting bracket (1) to junction box (not included) using two screws (2) to secure it.
6. For additional support, mark appropriate mounting locations using the slots on the mounting bracket (1) as guide. Take the mounting bracket (1) down and punch a small hole in the wall at each of the locations you have marked using a nail or an awl to see if there is a wall stud. Where there is a wall stud, use a wood screw (6) to mount the bracket. Where there is no stud to screw into, drill a larger hole for a wall anchor (5) then re-install mounting bracket using previous hardware to secure it.

Wiring – All wiring must take place inside junction box (not included)
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for damage or scrapes. If power supply wires are within three inches of the LED driver, use wire suitable for at least 90°C (194°F). Note: Most dwellings built before 1985 have supply wire rated to 60°C. Consult a qualified electrician to ensure correct branch circuit conductor before installing.

Step 2 – Wiring fixture

• Make all wire connections to appropriate wire. Secure with wire nuts (provided).
• Connect the green wire from the fixture to the supply power source ground wire.
• Connect the white wire from the fixture to the white (N) wire from the supply power source.
• Connect the black wire from the fixture to the black (L) wire from the supply power source.
• Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors. Tuck all connections neatly into the junction box.

Step 3 – Mounting fixture
A. Install the fixture (3) to the mounting bracket (1) using four screws (4) to secure it.

Step 4 – Color Changing Temperature Adjustment, CCT (if desired)
A. Adjust CCT switch to desired temperature of 2700K, 3000K, 3500K, 4000K, or 5000K as seen below. Note: Fixture is preset to 3000K from factory.

Step 5 – Restore power at fuse or circuit breaker box

Step 6 – Operation (Figure 2)

• The right pull switch operates the uplight and downlight by pulling on the chain once to turn on the uplight, pull twice to turn on the downlight, third pull to turn on both uplight and downlight, and fourth pull to turn both lights off.
• The left pull switch operates the night light by single pull to turn night light on and pull twice to turn off.

View shown for reference only. Individual models may vary.

Limited Factory Warranty

AFX Inc. hereby warrants that this fixture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years from date of purchase. This warranty covers all component parts and extends only to replacement of defective fixture or components; it does not cover failure due to improper installation, misuse, mishandling or damage incurred in transit.

2345 N. Ernie Krueger Circle Waukegan, IL 60087

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>