AFX LIGHT 16-2040 LED Crazy-Dance Floor User Manual

AFX LIGHT 16-2040 LED Crazy-Dance Floor

EXPLANATION OF SYMBOLS Please read this manual carefully before operating this product.

SAFETY RECOMMENDATIONS

•  Please read these instructions carefully, they include important information about the installation, usage and maintenance of this product.
•  Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives this instruction booklet.
• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the unit.
• This product is intended for indoor use only!
•  To prevent risk of fire or shock, do not expose fixture to rain or moisture.
• The max. ambient temperature (Ta) is 40°C. Don’t operate the fixture at higher temperatures.
• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
• Never disassemble the parts while power is on.
• Put the product only on a flat, stable surface.

INSTALLATION

Be very careful during installation to avoid bumps and damages. First assemble all parts before connecting the dancefloor to the mains and signal. The slabs must be connected to each other according to the arrows on the bottom with the proper orientation. DO NOT rotate the slabs by 90° or 180°! Place the slabs on the floor by following the direction of the arrows and align the magnets perfectly to the magnets of the previous slab otherwise the signal and power will not be transmitted properly. The 4 corners of every slab are empty to pass the signal and power lines. Once you have aligned all slabs, connect the controller and the power adapter to top edge of the dance floor. Now place the edges around the dance floor.

POWER SUPPLY
This product uses an external power adaptor as the lamps are powered by DC28V. The external power supply converts 100-250V~ voltage into 28V for use by the fixture.
Connect the supplied SD controller to the slabs as shown on the illustration.Connect the SD controller to your PC
The SD controller has 8 outputs. Each output can drive to 16 columns. Each column can contain 28 slabs maximum. So one controller can connect: 8 * 16 = 128 slabs.
The following is the PC controller 3×3 signal line connection diagram:

OPERATION OF THE SD CONTROLLER

Input connectors

(CD/mi- crophone)
IN| Main control input, connect the last controller via net cable
OUT| Main control output, connect the next controller via net cable

OUTPUT CONNECTORS

TOP VIEW

BASIC OPERATION

enter menu setting mode
SPEED/ENTER| Speed| Normal mode: 1-18 class
| | Exchange mode: 1-9 class
| Enter| On menu mode, press [enter] to save the current setting, lights will change the effect immediately.
MODE| Mode-| Mode decrease exchange
MODE| Mode+| Mode increase exchange
Menu Status| LED display| Operating Instruction
---|---|---
Enter into menu setting| Long press [MENU] 2 seconds, into menu setting mode
Menu setting| Master-slave| Master Slave| 1) press [ u ] [ t ] select master- slave, press [ ENTER ]
2) press [ u ] [ t ] to select
3) press [ ENTER ] to save settings
4) press [ MENU ] to quit
DMX address| DMX address| 1) press [ u ] [ t ] to select DMX address, press [ ENTER ]
2) press [ u ] [ t ] to select
3) press [ ENTER ] to save settings
4) press [ MENU ] to quit
Time, date| week date time| 1) press [ u ] [ t ] select time and date, press [ ENTER ]
2) press [ u ] [ t] to select
3) press [ ENTER ] to save setting
4) press [ MENU ] out
Language| Chinese English| 1) press [ u ] [ t ] select language, press [ ENTER ]
2) press [ u ] [ t ] to select
3) press [ ENTER ] to save setting
4) press [ MENU ] to quit
Brightness setting| Brightness | 1) press [ u ] [ t ] to select brightness set- ting, press [ ENTER ]
2) press [ u ] [ t ] to select
3) press [ ENTER ] to save setting
4) press [ MENU ] to quit
Sensitivity setting| Sensitivity **| 1) press [ u ] [ t ] select sensitivity, press [ ENTER ] in
2) press [ u ] [ t ] to select
3) press [ ENTER ] save setting
4) press [ MENU ] out
Exit menu setting| Long press [ MENU ] 2 second, exit menu set- ting mode and go back to control mode

IMPORTANT NOTE: Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed.

10

|

Mode 40-59

| 0-12| No
---|---|---|---
13-24| Mode 40
25-36| Mode 41
37-48| Mode 42
49-60| Mode 43
61-72| Mode 44
73-84| Mode 45
85-96| Mode 46
97-108| Mode 47
109-120| Mode 48
121-132| Mode 49
133-144| Mode 50
145-156| Mode 51
157-168| Mode 52
169-180| Mode 53
181-192| Mode 54
193-204| Mode 55
205-216| Mode 56
217-228| Mode 57
229-240| Mode 58
241-255| Mode 59
11| Mode 60-79| 0-12| No
13-24| Mode 60
25-36| Mode 61
37-48| Mode 62
49-60| Mode 63
61-72| Mode 64
73-84| Mode 65
85-96| Mode 66
97-108| Mode 67
109-120| Mode 68
121-132| Mode 69
133-144| Mode 70
145-156| Mode 71
157-168| Mode 72
169-180| Mode 73
181-192| Mode 74
193-204| Mode 75
205-216| Mode 76
217-228| Mode 77
229-240| Mode 78
241-255| Mode 79

12

|

Mode 80-96

| 0-14| No
---|---|---|---
15-28| Mode 80
29-42| Mode 81
43-56| Mode 82
57-70| Mode 83
71-84| Mode 84
85-98| Mode 85
99-112| Mode 86
113-126| Mode 87
127-140| Mode 88
141-154| Mode 89
155-168| Mode 90
169-182| Mode 91
183-196| Mode 92
197-110| Mode 93
111-124| Mode 94
125-138| Mode 95
139-255| Mode 96

References

• AFX LIGHT

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>