YITAHOME HNXD-V1 Fireproof Document Bag Instruction Manual

ASSEMBLY INSTRUCTIONS
HNXD-V1
IMISSB-0008
IMISSB-0009
SAFE BOX

HNXD-V1 Fireproof Document Bag

1. Confirm all parts are present prior to assembly.
2. Do not lock the emergency key or emergency battery box into the cabinet.

How to use the adjustable shelf

Turn the fastener clockwise and pull out the fastener horizontally, you can adjust the position of the shelf or take out the shelf according to your needs.

How to Mount the Safe:

1. Position the cabinet near the wall and mark the locations of the anchor holes using a marker.
2. Use a hammer drill to create holes at the marked positions.
3. Move the cabinet to its designated location and insert expansion screws into the drilled holes with a hammer.
4. Tighten the expansion screws securely to complete the installation.

User Manual for Electronic Lock

First-Time Safe Setup:

1. For security key on the left (black) to the right of the products for emergency key (black) if you want to use the emergency key/password lock needs to be blue security key clockwise for lateral, if the blue of the security key for the vertical cannot use the emergency key/password lock, please keep the key, if lost, please contact us in time.
2. Install the batteries.
3. Set the password (refer to the detailed instructions in the following).

User Manual for Electronic Lock
I. Initial Power-up:

1. Upon the system’s first power-up, the initial password is set to a personal code of “1234” and an administrative code of “123456”.
2. After a power outage, the password and records of door openings will still be saved.

II. Door Opening Operation:

1. In standby mode, press the “#” key to enter the password verification state, enter the correct password verification, the buzzer “beep” two sound, open the door.
2. Verification failed. Buzzer beeps three times.
3. If you enter the incorrect password three times in a row, the screen will display an alarm symbol, and the alarm will sound for one minute. Entering the correct password at this time will disable the alarm and unlock the door.
4. If no key is pressed within 8 seconds during input, the system will return to standby mode.
5. If no keyis pressed within 8 seconds during input, the system will return to standby mode.

Tips: Press the setting key for 4-5 seconds. If you hear a beep, the initialization is successful. The user password and management password are restored to their initial state. The initial Settings are as follows: The administrator password is 123456. The password is 1234.

III. Changing Personal Password:

1. Tap the setting buzzer for two drops to enter the password Password setting: Enter the setting mode, enter the 4-8 password press # to confirm, the buzzer drops 2 sounds and flashes twice at the same time, then enter again, press # to confirm, the buzzer often rings, the setting is successful.
2. If the password number is not within the specified range when entering the password, or if the password is not the same as the first time when entering password, or if the password is not the same as the first time when entering exit the setting mode. The setting fails and needs to be reset.

IV. fingerprint setting :

1. After entering the setting mode, place your finger on the fingerprint reader and move your finger four times after each beep of the buzzer.
   After the last input, the buzzer often rings , and the setting is successful.

2. If you leave or cannot recognize the input during the setting process, the buzzer beeps and exits the setting mode. The setting fails and needs to be reset.

V. Changing the Administrator Password:

1. After waking up the panel, press the “0” key twice, and then press the setting key to enter the management password setting, After entering the 4-8 password Press # to confirm, the buzzer drops 2 sounds and then enter again, then press # to confirm.
2. If the password number is not within the specified range when entering the password, or if the password is not the same as the first time when entering the password for the second time, press # to confirm, the buzzer will beep three times, exit the setting mode. The setting fails and needs to be reset.

VI. Set the two-factor authentication mode:

1. In the standby state, press the setting key twice. When you hear a beep, the green light is on, and the dual authentication mode is enabled.
   “Beep” two sound, cancel the dual authentication mode;
   “Beep” three times, empty fingerprint, cannot set dual authentication mode

2. The door can be opened only after the password and fingerprint are verified.

VI. Mute function:

1. Wake up the panel, press #00, hear “beep” two times at the same time turn off the mute function, wake up the panel, press #00 key, without sound, open the mute mode.

VII. Vibration alarm function:

1. Press the “*” key, hear “beep”, turn on the vibration alarm function, wake up the panel,

2. press the “*” key, hear “beep” twice, turn off the vibration alarm function.
   Alarm triggered alarm 30S, enter the correct password can stop the alarm, after opening the door, the vibration alarm function automatically closed.

3. Door opening error alarm
   When six consecutive fingerprint errors or four consecutive password errors are entered, a sharp alarm will sound inside the safe.

4. The alarm can last for up to 1 minute. In the above two cases, only enter the correct.password or fingerprint to open the cabinet door can be lifted. In the case od dualauthentication, the password and fingerprint must be at the same time to be lifted.

Vlll. Power and voltage in dicator:
The voltage is below 4.8V, and the blue light flashes when the door is verified.
Battery voltage is lower than 3.8V, when the user operates, the user is prohibited to operate, and the buzzer sounds “Didi, didi, didi” 6 to remind the customer that the battery is low.

1. replace the batteries.
2. Operating voltage: 4.2~7.5V
3. Operating current: 320mA
4. Static current: 35uA (at 6.0V)
5. Operating temperature: 0-50 ℃

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>