Johan Lewis ADA 5LT SEMI FLUSH User Manual
- June 7, 2024
- JOHAN LEWIS
Table of Contents
IL4162
User manual
ADA 5LT SEMI-FLUSH
Thank you for
purchasing this Ada semi-flush. Please read the instructions carefully before
use to ensure safe and satisfactory operations of this product. Please keep
this instruction for future reference.
Warnings!
For your safety, this product must be installed in accordance with local
Building Regulations. If in any doubt, or where required by the law, consult
a competent person who is registered with an electrical self-certification
scheme. Further information is available online or by phone at your Local
Authority. To prevent electric shock, switch off the mains supply before
installing or maintaining this product. Ensure other persons cannot restore
the electricity supply without your knowledge. Always use the correct bulb
type with the correct wattage as indicated in the specification table.
This product is Class = and should be fitted to a lighting Supply protected by
a 5 amp fuse or equivalent circuit breaker. When changing the bulb, always
switch off at the mains and allow the old bulb to cool down before handling.
Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use. For
indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish. Replace bulb from John Lewis or established brand of the same type and compatibility.
Parts list
Assembly
Never install your appliance on a wet, freshly painted, or plastered surface. Ensure the house electricity supply is switched off at the fuse box. If removing an existing fitting, note down all wiring connections. Check the fixings will not touch any existing wiring before drilling and attaching the light to the ceiling. Ensure you thread the ceiling wires through the black insulating tube fixed to the appliance.
Step 1
Remove mounting bracket from the fitting by removing the retaining screws and
any washers, retain for later. Using the mounting bracket as a template, mark
and then drill the fixing holes in the ceiling (ensure the screws are firmly
fixed into a solid or other suitable mounting and not just the plasterboard.)
Take care not to damage wiring. Attach the mounting bracket to the mounting
surface using suitable fixings. Do not attach the fitting to the mounting
bracket at this stage. Make sure no wires are trapped in the process.
Step 2
Ensuring that the power has been isolated, lever open the terminal block box
cover with a screwdriver then feed supply cable through rubber sleeving and
make electrical connections as follows:
• Connect the supply Live (Normally brown or red) to fitting life (marked “L”)
• Connect the supply neutral (blue or black) to fitting neutral (marked “N”)
NO EARTH must be connected to any part of this fitting.
Please note that residential wiring can vary, if you are unsure about the
correct polarity please consult a qualified electrician.
Step 3
The excess cable must be carefully located inside the ceiling cup or within
the ceiling cavity itself. Carefully offer fitting over mounting bracket then
secure in place with the screws and any washers removed earlier.
Fit the bulb: type and wattage as indicated on the fitting. If using
tungsten-halogen bulbs these must be self-shielded bulbs marked 
Do
not touch halogen bulbs with bare hands as this will shorten their life. The
wattage indicated must not be exceeded.
Fit the shades Remove the shade ring from the lamp holder and place it
inside the plastic shade ring tool provided. Offer the shade over the lamp
holder and replace the shade ring to secure it in place. Take care, not to
over tighten as this may damage the fitting. Once installation is complete,
the house electricity may be restored.
Recommended bulb
5 x 2-3 Watt G9 energy-efficient LED or
5 x 20 Watt G9 eco halogen capsule
Bulb not included
Specification
Max power: 20W
Voltage: 220~240V, 50/60Hz
IP20
Weight 2.3Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal
household waste and should be recycled. John Lewis does not operate in-store
take back, but members of the Distributor Take Back scheme have funded the
development and upgrade of recycling facilities across the UK. Please take it
to your nearest collection facility or for further details contact your local
council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
lightingparts@JLPspares.co.uk
Troubleshooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off the light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 1 04/19
References
- John Lewis & Partners | Department Store | Home, Fashion, Tech & More
- Everything you need to know to Recycle More
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>