BRISTAN TAN ES BAS BLK Tangram Black Eco Start Basin Mixer with Clicker Waste User Guide

Installation Instructions & User Guide
Please leave these instructions with the end user

Tangram Eco Start Basin Mixer Range
TAN ES BAS (D1)

Specifications

Pack Contents

Operation

Temperature Control
For cold water, position the handle straight forward so it is parallel with the spout (the handle will stop here when pushing it to the right)
To increase temperature, turn the handle to the left
The temperature will gradually rise the further the rotation of the handle
The handle will cease to turn once it is at a 90° angle, supplying the maximum temperature

Tools Required for Installation/ Maintenance

Prior to Installation

All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014 For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.co.uk/approvals-directory Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc.
Full access must be made available for future maintenance/servicing purposes
This product must not be modified in any way as this will invalidate the guarantee.

Spare Parts

http://www.bristan.com/search
To replace any spare parts for your tap, why not scan the QR Code or visit www.bristan.com and search for your product.

Important
The images shown are for illustrative purposes only.
The tap you have purchased may look different to those pictured in this booklet but will follow the same installation steps.
Your contents page will be specific to your product.
If you find your product or any of its components differ from those shown on the contents page, please contact our customer support.

Installation

Look underneath the tap body to observe fixing kit rod(s) and tail inlet positions      Depending on the model, the tap will utilise 1 or 2 fixing kit rods. Refer to your contents page

Screw in the fixing kit rod(s) into the base of the tap with a screwdriver
Screw in the flexible tails by hand only. DO NOT OVERTIGHTEN Your model may come with a plinth and will either be included pre-attached or loose in the box*
If required, thread the flexible tails and fixing kit rods through the plinth and rubber seal (if loose) and align with tap body Take note of any grub screw holes on the underside of the tap and align them correctly to the holes on the plinth
Thread the flexible tails and fixing kit rods through the basin holeIf the hole is not large enough for both tail ends to fit through, screw one of the tails in from underneath the basin
From underneath the basin, slide the rubber gasket and metal ¢ plate along the fixing rod(s) with the gasket sitting on top of the c plate  Align the gasket and c plate, then begin tightening the nut up the rod towards the basin until secure.
Connect the hot  and cold water supplies to the flexible tails and turn until tight

Waste Installation and Operation

Fit the waste above the basin ensuring the washer is in place Push waste into hole until the outer rim sits flush with the bottom of the basin Then place the washer from underneath and tighten the backnut to secure the waste to the basin.
Push the centre down to close the waste Push again to open and release the contents of the basin
Your waste is now ready for use.

General Cleaning

Bristan products are made from premium materials, with hand polished, electroplated, PVD or EPD finishes.
Your taps or shower should be regularly cleaned with warm water, a mild pH- neutral liquid soap, and polished with a soft cloth. Any residues from soap, toothpaste, shampoos and shower gels can cause blemishes if not rinsed off straight after use.
Household bleaches and cleaners contain harsh chemicals and may damage the surface finish. Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.

Maintenance – Cartridge/ Valve Replacement

Maintenance – Clean/ Replace Outlet

Love Your Chrome

Bristan offers an effective chrome-friendly cleaning kit for use with your taps and showers. Scan the QR Code or search for ‘CLEAN KITOT on www.bristan.com. Notes
Please use this space for any notes you or your installer may have regarding the installation/plumbing of this product. ‘
Contact Us
BRISTAN
Bristan Group Ltd.
UK:Bristan Group, B78 1SG.
EU: Masco Europe S.a.rl.
14 Rue Strachen
6933 Mensdorf
Luxembourg
Customer Service: +44330 026 6273
Web: www.bristan.com
Email: enquire@bristan.com
A Masco Company

Servicing Your Tap

We recommend servicing your tap at least once every year to prolong its life. To see a video showing how to remove the cartridge for servicing, scan the QR code with your smart phone or tablet. Alternatively visit www.youtube.com/BristanTV

Our Guarantee

At Bristan, we want to make things as easy as possible for our customers. That’s why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind.
Your guarantee starts from the purchase of your product, but you can still benefit from registering it for easier identification in the unlikely event of a manufacturing fault, please visit www.bristan.com/register
For any other gueries, please call Customer Service on 0330 026 6273 where our expert team of advisors will be able to offer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service- centre/guarantees.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>