MARSAIL TZESD4B Electric Standing Desk Instruction Manual

MARSAIL TZESD4B Electric Standing Desk

Model:

• TZESD4B/TZESD4V/TZESD4N
• TZESD5B/TZESD5V/TZESD5N

Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.
877-201-4016
help_service_center@outlook.com

Specifications

Tools Needed

(not included)

Supplied Parts and Hardware

Step 1 Step 2

Step 3

Step 4

Step 5

Assembling the Frame

Align holes in the crossbar with holes in the desk legs, and insert four bolts. Partially and then fully tighten each pair of bolts.

Insert four bolts through each leg base and into each leg. Partially and then fully tighten the bolts in each leg. Attach the side plates.

Slide the rod coupler onto the end of the motor drive shaft on the right leg. Adjust uneven desk legs:
Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod, using the wrench, to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Slide the rod coupler into the left to connect with the other end of the transmission rod.

Note : If the transmission rod doesn’t flt smoothly into the hole of rod coupler, fine-tune with the wrench.

Use the set screws to secure the rod coupler.

Ensure rubber pads are attached to the frame. If any have fallen off, reattach them or use spare rubber pads.

Assembling the Desktop

For the 48″ long desk, use the five wood dowels to join the two desktop panels together.

For the 55″ long desk, use the six wood dowels to join the two desktop panels together.

Secure the desktop panels with the connectors.

Attaching the Desktop

Attach the frame to the desktop.

Note : An off-center screw hole is not a problem. The pre-drilled holes are only guides for easier screw-in. If you have any questions or issues, please contact us at help_service_center@outlook.com.

Put the AC adapter into the holder.

Attach the controller, AC adapter with holder, and storage hooks to the desktop.

Connecting the Cables

Attaching the Stand and Drawers
Screw cam bolts into the stand top panel.

Screw cam bolts and push wood dowels into the stand back panel.

Connect the stand top panel and stand back panel together.

Secure with cam locks.

Attach drawer inside panels and stand center support.

Secure with cam locks.

Screw cam bolts and push wood dowels into drawer side panels.

Attach drawer side panels.

Secure with cam locks.

Push the wood dowels into seven larger holes in the desktop.

Attach the assembled stand to the desktop.

Raise the desk to a convenient height, and then secure the stand with screws.

Unfold the fabric drawers.

Place bottom pads in the drawers.

Insert the fabric drawers.

Using the Controller

Note : Ensure that there are no obstacles when using the desk, that the desktop is not right next to the wall, and that all cables are long enough for the desk to move up and down freely. When the controller screen is off (power- saving mode), press any button to wake it before operating the desk.
Suggestion : Set the most comfortable height when you sit down to 1 and the most comfortable height when you stand up to 2 . The other two presets can be set for another user or to other heights you want to use.

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position of 46.4″ (118cm) or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position of 27.5″ (70cm) or the button is released.

• Save Height Settings
  Four heights can be stored. Press and hold the 1/2/3/4] button for 3 seconds. The digital number will flash three times and the current height will be stored to that button.

• Select Height Setting 1
  Press the 1 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

• Select Height Setting 2
  Press the 2 button, and the desk will move to the height that was previously set for that button.
  Press any button to stop the desk.

• Select Height Setting 3
  Press the 3 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

• Select Height Setting 4
  Press the 4 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Settings

Change Display Height Units

| ****

Press and hold [I] and [ll buttons together for 3 seconds to switch the display height unit. The default unit is inches.

---|---

Change Collision Detection Sensitivity

| ****

1.  Press and hold [I] and@] buttons together for 3 seconds, and ‘S02’ will flash on the screen. The last digit displayed is the current sensitivity level, and the value range is 0-3 (0: off; 1-3: highest to lowest).

2.  Select other levels by pressing l2S] or 521 button, and then press and

hold [I] and @] buttons together for 3 seconds. The digits will stop flashing, and the screen will display current height again.

Set/Clear Lowest Limit

| ****

1.  To set the lowest height limit, press and hold 521 and [I] buttons together for 3 seconds, and the screen will display ‘-dO’ Whenever the desk reaches the lowest limit, the screen will display ‘-LO’.

2. To clear the lowest height limit, move the desk down to the lowest height (screen displays ‘-LO’) and press and hold 521 and [I] buttons

together for 3 seconds. ‘-dO’ will flash on the screen, and the limit will be cleared.

Set/Clear Highest Limit

| ****

1.  To set the highest height limit, press and hold l2S] and [I] buttons together for 3 seconds, and the screen will display ‘-UP’ Whenever the desk reaches the highest limit, the screen will display ‘-HI’.

2. To clear the highest height limit, move the desk up to the highest height (screen displays ‘-HI’) and press and hold l2S] and [I] buttons together for 3 seconds. ‘-UP’ will flash on the screen and the limit will be cleared.

Troubleshooting

1. Please try resetting the desk if you have any issues like the following:

•  Abnormal operation.

•  The controller screen displays ‘RST’ (reset).

•  The controller screen displays error message E07 or E0B, but the motor cable is connected correctly.

2. If the controller screen displays ‘HOT,’ please wait 20 minutes for the motor to cool down before making any further height adjustment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>