Marsail MSOC4 Office Chair Instruction Manual
- June 17, 2024
- MARSAIL
Table of Contents
Marsail MSOC4 Office Chair
Features
-
Folding Armrest:
Lower the armrest for support or raise it up when not in use. -
Seat Height Adjustment:
To raise the seat, lift your body off the chair, then pull the lever up. To lower the seat, rest your body in the chair, then pull the lever up.
-
Backrest Rocking Function:
Pull the lever out to enable the rocking function. T he chair will rock back and forth with the user rather than being locked in a fixed position. Return the lever to its original position to lock it. -
Backrest T ilt Tension Adjustment:
Turn the knob[+] or[-] to increase or decrease the rocking tension. Tip: Tension can be adjusted to suit a particular weight. Increase tension for heavier weight and decrease tension for lighter weightWARNING!
WARNING!
Only trained personnel!
A may replace or repair seat height! adjustment components with energy
accumulators.
INSTALLATION INSTRUCTION
Missing Parts?
Step 1 Supplied Parts and Hardware
Step 2 Supplied Parts and Hardware
Step 3 Supplied Parts and Hardware
Step 4 Supplied Parts and Hardware
Step 6 Supplied Parts and Hardware
Support
Step 1 Assembling the Chair Legs Remove the decorative cover and keep it
for Step 2.
Insert the legs [02] into the leg connector [Ola], then secure with bolts [A].
Step 2 Attaching the Casters and Gas Lift Cylinder Press the casters [03] firmly into the holes on the legs [02].
Flip over the assembled base. Attach the decorative cover [Olb], then press the gas lift cylinder [Oli] into the leg connector.
Step 3 Assembling the Armrests, Backrest and Seat
-
Align the holes on the left armrest [07] with the holes on the backrest [09], then secure with bolts [C].
NOTE : Do not fully tighten bolts [C] until Step 3-li is finished.
NOTE: You need to place a layer of packaging bags or rugs on the floor to prevent scraping. -
Align the holes on the left armrest [07] with the holes on the seat [05], then secure them with bolts [C].
NOTE: Do not fully tighten bolts [C] until Step 3-li is finished. -
Attach the other side in reference to Step 3-1.
NOTE: Do not fully tighten bolts [C] until Step 3-li is finished. -
Attach the other side in reference to Step 3-2.
NOTE: Remember to fully tighten all the bolts [C] in this step.
Step 4 Attaching the Lift Mechanism Attach the lift mechanism [06] to the seat [05] with bolts [B].
Step 5 Attaching the Chair to the Base Align the hole underneath the chair with the gas lift cylinder [Oli]. Press the seat down to secure the chair to the base.
Step 6 Attaching the Covers Attach the covers [D] to the bolt holes on both sides of the armrests.
IMPORTANT SAFETY INFORMATION
- Compare package contents to the supplied parts and hardware list to confirm that all parts were received and undamaged. Do not use damaged or defective parts. If you require replacement parts, please email customer service.
- Carefully read all instructions before attempting installation. If you have any questions or concerns, please email customer service.
Care and Maintenance
How to Clean
- It is recommended that the office chair be thoroughly cleaned at least once a month to maintain condition and functionality.
- Use a vacuum cleaner to suck up the dirt that may be resting on the seat.
- The casters will stick if not maintained regularly. Brush the casters with water and wipe clean with a damp cloth.
- If dirt solidifies on the surface of the casters, use soap and water to clean it off.
- Use a dry cloth to finish cleaning, or leave your office chair in a ventilated area to air dry.
Maintenance Tips
- Direct sunlight can ruin an office chair over time, degrading most fabrics and materials. Keep your office chair out of direct sunlight.
- Humid conditions may lead to the formation of mildew on fabric and/or rust on metal parts. Do not keep your office chair in a damp environment.
- Be careful with drinks, food, or any type of liquids when you are near your chair. If a spill happens, clean and attend to stains immediately.
- Avoid the use of sharp objects or blades near the office chair that may cause damage.
- If possible, cover the chair to protect it from dirt and dust.
- Regularly examine the chair to ensure that all nuts and bolts are correctly fastened, including those connecting the seat, back, and chair mechanics.
- Retighten bolts every 6 months by using the included Allen key.
Using an electric drill can damage the chair. Only use hand tools.
Thank you for choosing this product. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.Gracias por elegir este producto. Nos esforzamos por ofrecerte productos y servicios de la mejor calidad en la industria. Si tienes algún problema, no dudes en contactarnos.
contact
- 877-201-4016
- helpservicecenter@outlook.com
- 860-02217-00 Rev01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>