MARSAIL TZESD10B Electric Standing Desk Instruction Manual

Electric Standing Desk Instruction Manual
Rev01(A)

TZESD10B Electric Standing Desk

Model:
TZESD10B / TZESD10V / TZESD10N

Thank you for choosing this product! We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us at service.wowowo@gmail.com.

Specifications

Height Adjustment Range: 28.3″–46.5″ (72-118cm) Tools Needed (not included)

Supplied Parts and Hardware for Step 1

Supplied Parts and Hardware for Step 2 Supplied Parts and Hardware for Step 3 Supplied Parts and Hardware for Step 4 Supplied Parts and Hardware for Step 5 Supplied Parts and Hardware for Step 6

Step 1: Assembling and Connecting the Desk Legs

Step 2: Attaching the Side Plates and the Transmission Rod

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it. Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.  ![MARSAIL TZESD10B Electric Standing Desk

• Step 11](https://manuals.plus/wp-content/uploads/2023/11/MARSAIL-TZESD10B- Electric-Standing-Desk-Step-11.jpg)Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.Tighten the coupling nut to fine-tune transmission rod fit.

Step 3: Assembling the Desktop

Assemble the desktop.

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.
Secure the desktop panels with the connectors.

Step 4: Attaching the Desktop

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.Attach the desktop to the frame.Attach the controller and hooks to the desktop.

Step 5: Connecting the Cables

Step 6: Installing the Cable Hole Covers

Using the Controller

Save Current Height Setting
Short-press the button, and the display will flash. Press the , , or button to save the current height setting to that button.
Select Height Setting 1
Press the button, and the desk will move to the height that was previously set for that button.
Select Height Setting 2
Press the button, and the desk will move to the height that was previously set for that button.
Select Height Setting 3
Press the button, and the desk will move to the height that was previously set for that button.
Raise the Desk
Press the button to raise the desk continuously until it reaches the highest position of 46.5” (118cm) or the button is released.
Lower the Desk
Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

Settings

Change Display Height Units| Press and hold the button until a flashing ‘S-’ is displayed. Press again, and ‘Un’ is displayed. Press to select it, press or to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press to save your choice.
---|---
Change Collision Detection
Sensitivity| Long press the button, ‘S-’ shows and flashes. Press again and the display shows ‘Un.’ Press or to switch to ‘CF.’ Press to sel ect. Press or to switch between ‘OFF,’ Low (L), Normal (n) or Heavy (H) collision force detection. Press to save your choice.
Reset| Press and hold the button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
---|---
E10| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>