MARSAIL TZESD6B Electric Standing Desk Instruction Manual

MARSAIL TZESD6B Electric Standing Desk

Specifications

Tools Needed

Tools Needed (not included)

Supplied Parts

Supplied Parts and Hardware for Step 1

Supplied Parts and Hardware for Step 2

Note: An extra wood dowel pin is provided for the longer 55″ desk.

Supplied Parts and Hardware for Step 3

Supplied Parts and Hardware for Step 4

Supplied Parts and Hardware for Step 5

Assembling the Frame

Step 1: Assembling the Frame

Align holes in the crossbar with holes in the desk legs, and insert four bolts. Partially and then fully tighten each pair of bolts, making sure the legs flt smoothly into the crossbar grooves.
|

Hold the hook on the end of the crossbar. Attach the side plate over it using the bolts. Then attach the other side plate.

Slide the rod coupler onto the end of the motor drive shaft on the right leg.

Adjust uneven desk legs: Before attaching the transmission measure the heights of the two legs to see if they are set at the same level. If not, insert the transmission into the hole in the left leg. Turn using the wrench, to adjust the left so it’s level with the right leg. Turn the rod clockwise to raise the left leg anti-clockwise to lower it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Slide the rod coupler to the left to connect with the other end of the transmission rod.| Note: If the transmission rod doesn’t flt smoothly into the hole of rod coupler, fine-tune flt with the wrench.

Use the set screws to secure the rod coupler.

Ensure the rubber pads are attached to the frame. If any have fallen off, reattach them or use the spare rubber pads.

For the 40″ / 48″ long desk, use the five wood dowel pins to join the two desktop panels together.

For the 55″ long desk, use the six wood dowel pins to join the two desktop panels together.

You can use a drill with suitable torque and speed) or a Phillips screwdriver.
Secure the desktop panels with the connectors.

Step 3: Attaching the Desktop
Attach the frame to the desktop.

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

Note: An off-center screw hole is not a problem. The pre-drilled holes are only guides for easier screw-in. If you have any questions or issues, please contact us at service.wowowo@gmail.com.

Put the AC adapter into the holder.

Attach the controller and AC adapter with holder to the desktop.

You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

Step 4: Connecting the Cables

Step 5: Attaching the Side Pocket
Thread the bolts through the holes in the side pocket and the side plate from the outside. Screw the nuts onto the ends of the bolts from the inside of the side plate.

Using the Controller

Note: Ensure that there are no obstacles when using the desk, that the desktop is not right next to the wall, and that all cables are long enough for the desk to move up and down freely. When the controller screen is off (power- saving mode), press any button to wake it before operating the desk.
Suggestion: Set the most comfortable height when you sit down to 1 and the most comfortable height when you stand up to 2. The other two presets can be set for another user or to other heights you want to use.

Raise the Desk

Press the button to raise the desk continuously until it reaches the highest position of 46.7″ (118cm) or the button is released.

Lower the Desk

Press the **** button to lower the desk continuously until it reaches the lowest position of 27.5″ (70cm) or the button is released.

Save Height Settings

Four heights can be stored. Press and hold the 1/ 2/ 3/ button for 3 seconds. The digital number will flash three times and the current height will be stored to that button.

Select Height Setting 1

Press the 1 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Select Height Setting 2

Press the 2 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Select Height Setting 3

Press the 3 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Select Height Setting 4

Press the 4 button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

Reset|

1. Press and hold the button until the desk goes down to its lowest level, and then release the button.

2. Press and hold the button for 5 seconds until the screen displays ‘RST,’ and then release the button with ‘RST’ flashing.

3. Press and hold it again until the desk goes down to its lowest level and comes back up slightly. The screen will display current height again, and reset is complete.

Lock/Unlock| Press and hold 1 and 2 buttons together for 3 seconds to turn the lock on. The screen will display ‘LOC’ and the buttons will be disabled. Repeat to turn the lock off again.
Change Display Height Units| Press and hold 1 and 2 buttons together for 3 seconds to switch the display height unit. The default unit is imperial.
---|---
Change Collision Detection Sensitivity| 1.  Press and hold 1 and 4 buttons together for 3 seconds, and ‘S02’ will flash on the screen. The last digit displayed is the current sensitivity level, and the value range is 0-3 (0: off; 1-3: highest to lowest).

2.  Select other levels by pressing or 521 button, and then press and

hold and 1 button together for 3 seconds. The digits will stop flashing, and the screen will display the current height again.

Set/Clear Lowest Limit| 1.  To set the lowest height limit, press and hold the 521 and 1 buttons together for 3 seconds, and the screen will display ‘-dO’ Whenever the desk reaches the lowest limit, the screen will display ‘-LO’

2. To clear the lowest height limit, move the desk down to the lowest height (screen displays ‘-LO’) and press the 521 and and 1 button together

for 3 seconds. ‘-dO’ will flash on the screen, and the limit will be cleared.

Set/Clear Highest Limit| 1.  To set the highest height limit, press and hold and 1 button together for 3 seconds, and the screen will display ‘-UP’ Whenever the desk reaches the highest limit, the screen will display ‘-HI’

2. To clear the highest height limit, move the desk up to the highest height (screen displays ‘-HI’) and press and 1 button together for 3 seconds. ‘-UP’ will flash on the screen and the limit will be cleared.

Troubleshooting
1. Please try resetting the desk if you have any issues like the following:

•  Abnormal operation.

•  The controller screen displays ‘RST’ (reset).

•  The controller screen displays the error message E07 or EOB, but the motor cable is connected correctly.

2. If the controller screen displays ‘HOT,’ please wait 20 minutes for the motor to cool down before making any further height adjustments.

Thank you again for choosing this product!

All of us do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at service.wowowo@gmail.com. 860-00477-00 Rev05

Model

• TZESD6B / TZESD6V / TZESD6N
• TZESD7B / TZESD7V / TZESD7N
• TZESD8B / TZESD8V / TZESD8N

Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at service.wowowo@gmail.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>