Marsail TZESD11B Electric Standing Desk Instruction Manual

June 14, 2024
MARSAIL

Marsail TZESD11B Electric Standing Desk

Marsail-TZESD11B-Electric-Standing-Desk-PRODUCT

Model : TZESD11B / TZESD11V / TZESD11N
Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at service.wowowo@gmail.com.

Specifications

Marsail-TZESD11B-Electric-Standing-Desk-FIG-
\(1\)

Tools Needed (not included)Marsail-TZESD11B-Electric-Standing-Desk-FIG-
\(2\)

Supplied Parts and Hardware

Supplied Parts and Hardware for Step 1

Marsail-TZESD11B-Electric-Standing-Desk-FIG-
\(3\)

Supplied Parts and Hardware for Step 2Marsail-TZESD11B-Electric-Standing-
Desk-FIG- \(4\)

Supplied Parts and Hardware for Step 3Marsail-TZESD11B-Electric-Standing-
Desk-FIG- \(5\)

Supplied Parts and Hardware for Step 4Marsail-TZESD11B-Electric-Standing-
Desk-FIG- \(6\)

Supplied Parts and Hardware for Step 5

ASSEMBLING

Step 1: Assembling the FrameMarsail-TZESD11B-Electric-Standing-Desk-FIG-
\(8\)Marsail-TZESD11B-Electric-Standing-Desk-
FIG- \(9\) Marsail-TZESD11B-Electric-Standing-Desk-
FIG- \(10\) Marsail-TZESD11B-Electric-Standing-Desk-
FIG- \(11\)

  • Extend the frame out until the round screw holes on the tops of the two frame sections are aligned.
    NOTE : If extending the frame isn’t smooth, move the motor a little bit

  • Secure the two frame sections with the bolts

  • Attach the angle brackets to the frame.

  • Align the two sections of the transmission rod and then secure with the bolts. Fully tighten the pre-installed bolts holding the rod connector

  • Attach the motor cover.

Step 2: Assembling the DesktopMarsail-TZESD11B-Electric-Standing-Desk-
FIG- \(12\)

  • Connect the desktop panels with the connectors.

Step 3: Attaching the DesktopMarsail-TZESD11B-Electric-Standing-Desk-FIG-
\(13\)

Attach the controller and hook to the desktop.

Step 4: Connecting the Cables

Step 5: Attaching the Cable Hole Covers

Using the Controller

NOTE:

  1. Before use, check the cable connections.
  2. Ensure that there are no obstacles when using the desk.
  3. Keep children away from the desk.
  4. Do not use if any cables or electronic parts are damaged.
  5. This desk does not have casters. Please lift the desk carefully to move it.
  6. The desk may vibrate slightly when it moves up or down. This is normal.

Settings

Reset

| Tip: Reset before first use.

Press and hold the button for 3 seconds until ‘—‘ is displayed, and then release the button. The desk will go up to its highest level, down to its lowest level, and then stop. Reset is complete.

---|---

Raise the Desk

|

Long-press the button, and the desk will go up while the button is held down. After pressing for 3 seconds, the current height will flash and the desk will continue to move to the highest position by itself. Press any button to stop the desk.

Lower the Desk

|

Long-press the button, and the desk will go down while the button is held down. After pressing for 3 seconds, the current height will flash  and the desk will continue to move to the lowest position by itself. Press any button to stop the desk.

Save Standing Height Setting

| Press and hold the button for 3 seconds. The current height will flash and be saved to that button. When you press the button, the desk will move to the height that was previously set for that  button. Press any button to stop the desk.
---|---

Save Sitting Height Setting

| Press and hold the button for 3 seconds. The current height will flash and be saved to that button. When you press the button, the desk will move to the height that was previously set for that button. Press any button to stop the desk.
| Press the button to set the timer.
---|---
| T30: 30 minutes
| T45: 45 minutes
Reminder (Countdown Timer)| T60: 60 minutes

Current Height: Timer off

When the countdown is over, the desk will vibrate slightly and ‘Chr’ will

| flash on the screen to notify you.  Press the             button to switch the
| timer setting or turn off. Press any other button to restart the same
| countdown timer. If there is no button-press, the countdown timer
| notification will repeat two more times and then turn off.

Troubleshooting

  1. If the controller screen displays ‘RES’ or the desk is not working properly, please check cable connections and then follow the reset instructions.
  2. If the controller screen displays ‘HOT,’ the buttons will be disabled. Please wait 20 minutes for the motor to cool down before making any further height adjustment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals