MARSAIL MSESD10 Electric Standing Desk Instruction Manual

MARSAIL MSESD10 Electric Standing Desk

INTRODUCTION

Thank you for choosing this product! We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

• 877-201-4016
• help_service_center@outlook.com

Specifications

Tools Needed (not included)

Supplied Parts and Hardware for Step 1

Supplied Parts and Hardware for Step 2

Supplied Parts and Hardware for Step 3

Supplied Parts and Hardware for Step 4

Supplied Parts and Hardware for Step 5

ASSEMBLY INSTRUCTION

• **Step 1 : Assembling and Connecting the Desk Legs

**

• **Step 2: Attaching the Side Plates and the Transmission Rod

**

  * Loosen the coupling nut.

  * Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or counter-clockwise to raise it.

  * Ensure the transmission rod is properly inserted into the hole in the left leg. Carefully slide the other end of the rod onto the end of the motor drive shaft on the right leg.

  * Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

  * Tighten the coupling nut to fme-tune transmission rod flt, then attach the rubber pads.

• Step 3: Attaching the Desktop
  NOTE: There are pre-drilled holes on the bottom of the desktop.

• Step 4: Connecting the Cables
  NOTE: An example of a cable clip layout is indicated below. However, the cable clips can be arranged according to your needs.

• Step 5: Attaching the Backstops
  Attach the backstops on the back of the desk as demonstrated below, then insert the cable grommet.

Using the Controller

• Save Current Height Setting
  Short-press the button, and the display will flash. Press the , , or button to save the current height setting to that button.

• Select Height Setting 1
  Press the button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.

• Lower the Desk
  Press the  button to lower the desk continuously until it reaches the lowest position of 30.7″ (78cm) or the button is released.

Settings

• Change Display Height Units
  Press and hold the button until a flashing ‘S-‘ is displayed. Press again, and ‘Un’ is displayed. Press to select it, press or to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press to save your choice.

• Change Collision Detection Sensitivity
  Long press the button, ‘S-‘ shows and flashes. Press again and the display shows ‘Un.’ Press or to switch to ‘CF.’ Press to select. Press or to switch between ‘OFF,’ Low (L), Normal (n) or Heavy (H) collision force detection. Press to save your choice.

• Reset
  Press and hold the button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

• Hot Overheating Protection: When the motor has been working continuously for 5 minutes, it will stop operating to prevent damage from overheating. Wait for at least 15 minutes before making any further height adjustment.
• E10 Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
• E20
  • Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
  • If error code persists, follow the reset instructions.
• E02 Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
• E32 Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
• E31 Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
• E60 Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
• – Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>