RUTLAND COUNTY DBSC1 Morcott Double Wheelie and Recycling Bin Store Instruction Manual
- June 1, 2024
- RUTLAND COUNTY
Table of Contents
RUTLAND COUNTY DBSC1 Morcott Double Wheelie and Recycling Bin Store
Specifications:
- Dimensions: [Insert dimensions here]
- Material: [Insert material type]
- Color: [Insert color]
- Weight: [Insert weight]
Product Usage Instructions
Assembly Instructions
Before you commence the assembly process, ensure you have read the
instructions thoroughly to familiarize yourself with the components and steps
involved.
Tools Required:
10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver)
Step-by-Step Assembly:
Step 1:
Begin by assembling the left and right panels together with the back panels
using the provided screws and spacer blocks.
Step 2:
Attach the dividing frame using the shorter green screws as indicated in the
manual.
Step 3:
Proceed to add the remaining back panel and final side panel following the
same assembly method.
FAQ:
Q: What should I do if I encounter missing components during assembly?
A: If you are missing any components, please contact our customer support
for assistance.
Q: Can the bin store be painted or treated with wood preservatives?
A: It is recommended to check the manufacturer’s guidelines before
applying any additional treatments to the bin store to avoid damage or voiding
any warranties.
Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have the correct components. If for any reason you need assistance, you can find our contact details on the final page of these instructions.
We highly recommend that any assembly is carried out on an open flat, level surface if possible with sufficient space.
Tools required:
10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver)
Components
The Morcott Double Bin Store
Step 1
Begin by arranging the left panel (the one with the small wood block
attached to the front post) and the back panel at 90° to each other, with the
back panel raised up on the spacer blocks by approximately 25mm. Use 3 x
shorter green screws to secure as shown.
Step 2
Now add the Dividing frame, fixing in the same way with 3 x shorter green
screws.
Step 3
Add the remaining back panel and final side panel in the same manner as
before.
Step 4
Carefully lay the assembly on its back and attach the metal bars to the front
bottom edge of the 3 front posts as shown, securing in place with 2 x shorter
green screws per post.
Step 5
Stand the assembly back up and position the Hinge strip at the top of the rear
posts…
Step 6
…set the hinge bar so that the top edge sits approx. 15mm above the top of the
rear post and secure in place with a longer green screw into each of the 3
posts.
Step 7
Lower the lid assemblies into place and position them so that the hinge
knuckles sit against the hinge strip…
Step 8
..and there is a 15mm gap between the lid panels before fixing the hinges into
place with 3 x black screws per hinge into the hinge strip.
Step 9
Returning to the front of the store, place the finishing strip against the 3
front posts as shown with the screw holes configured to create a triangle and
slide it upwards until it is just touching the underside of the lid. Now fix
in place with 3 x shorter green screws per post.
Step 10
Align the door (hinge side on the left) so that the top edge clears the
underside of the finishing strip by approx 10mm and each hinge leaf sits flat
against the post with the knuckles resting against the front edge of the post.
Secure the hinges in place using 8 x black screws.
Step 11
Attach the second door in the same manner.
Step 12
Position the cabin latch keep on the post and aligned horizontally with the
latch as shown. Secure in place with 2 x black screws then repeat for the
second door.
Step 13
Take the coach bolt from the prop fixing and push it through the hole in the
prop, add a washer and then push through the hole in the lid batten as shown.
Step 14
Place another washer over the coach bolt and finally the securing nut. Tighten
with a spanner or socket until fully tight and then back off until the prop is
able to swing freely. Attach the second prop in the same manner.
Step 15
If your bin lid has a suitable handle you may use the chain provided to
attached this to the store lid. Undo the nut and slip one end over the
coachbolt, then pass other end through the handle and then over the end of the
coach bolt, pulling chain through until it is tight enough. Now re-attach the
nut.
Step 16
Your Morcott Double Bin Store is now complete.
We hope that you found your product quick and easy to assemble but if not and
you require any further assistance or have any questions you can contact us by
telephone on: 01778 440803
Email:
info@rutlandcountygardenfurniture.co.uk
www.rutlandcountygardenfurniture.co.uk
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote
Meadows,Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>