RUTLAND COUNTY GARDEN FURNITURE TRBSC1 Morcott Triple Wheelie Recycling Bin Store Instruction Manual
- June 1, 2024
- Rutland County Garden FURNITURE
Table of Contents
RUTLAND COUNTY GARDEN FURNITURE TRBSC1 Morcott Triple Wheelie Recycling Bin Store
IMPORTANT INFORMATION
Before you commence the assembly process we recommend that you read these
instructions thoroughly beforehand to familiarise yourself with the assembly
process and to also check that you have the correct components. If for any
reason you need assistance, you can find our contact details on the final page
of these instructions.
We highly recommend that any assembly is carried out on an open flat, level
surface if possible with sufficient space.
Tools required: 10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver)
Components
38 x Short screws 8 x Long screws| 3 x Latch keep & 48 black screws| 3 x Prop
fixing| 2 x Spacer blocks| 3 x Metal bar| 3 x Chain
---|---|---|---|---|---
| | 
| 
| 
| 
1 x Left panel| 1 x Right panel| 3 x Back panel| 2 x Outer lid assembly| 1 x
Centre lid assembly| 3 x Door
| 
| 
| | |
2 x Dividing frame| 3 x Prop| 1 x Hinge strip| 1 x Finishing strip| 2 x Shelf
rail| 1 x Shelf
| 
| 
| 
| 
|
Assembly Instructions
Step 1
Begin by arranging the left panel (the one with the small wood block attached
to the front post) and the back panel at 90° to each other, with the back
panel raised up on the spacer blocks by approximately 25mm. Use 3 x shorter
green screws to secure as shown.
Step 2
Now add the Dividing frame, fixing in the same way with 3 x shorter green
screws.
Step 3
Continue by adding the remaining back panel and final side panel in the same
manner as before.
Step 4
Carefully lay the assembly on its back and attach the metal bars, the centre
bar being the shorter one, to the front bottom edge of the 3 front posts as
shown, securing in place with 2 x shorter green screws per post.
Step 5
Stand the assembly back up and position the Hinge strip at the top of the rear
posts…
Step 6
…set the hinge bar so that the top edge sits approx. 15mm above the top of the
rear post and secure in place with a longer green screw into each of the 3
posts.
Step 7
Lower the lid assemblies into place, the centre lid being the narrower one,
and position them so that the hinge knuckles sit against the hinge strip…
Step 8
..and there is a 15mm gap between the lid panels before fixing the hinges into
place with 3 x black screws per hinge into the hinge strip.
Step 9
Returning to the front of the store, place the finishing strip against the 3
front posts as shown with the screw holes configured to create a triangle and
slide it upwards until it is just touching the underside of the lid. Now fix
in place with 3 x shorter screws per post.
Step 10
Set one of the shelf rails against the inner face of a side panel/dividing
frame, dependent on which bay you’d like the shelf in, spanning the vertical
battens at a suitable height to accommodate your box. Ensure it is level (use
the horizontal slats as a guide if necessary) and fix in place with a longer
screw though each end into the batten…
Step 11
…then repeat for the other side ensuring the opposite rail is at the same
height. Now drop the shelf into place.
Step 12
Align the door (hinge side on the left) so that the top edge clears the
underside of the finishing strip by approx 10mm and each hinge leaf sits flat
against the post with the knuckles resting against the front edge of the post.
Secure the hinges in place using 8 x black screws.
Step 13
Attach the second and third door in the same manner.
Step 14
Position the cabin latch keep on the post and aligned horizontally with each
latch as shown. Secure in place with 2 x black screws then repeat for the
second and third door.
Step 15
Take the coach bolt from the prop fixing and push it through the hole in the
prop, add a washer and then push through the hole in the lid batten as shown.
Step 16
Place another washer over the coach bolt and finally the securing nut. Tighten
with a spanner or socket until fully tight and then back off until the prop is
able to swing freely. Attach the second and third prop in the same manner.
Step 17
If your bin lid has a suitable handle you may use the chain provided to
attached this to the store lid. Undo the nut and slip one end over the coach
bolt, then pass other end through the handle and then over the end of the
coach bolt, pulling chain through until it is tight enough. Now reattach the
nut.
Step 18
Your Morcott Triple Recycle Bin Store is now complete.
CUSTOMER SUPPORT
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762
We hope that you found your product quick and easy to assemble but if not and
you require any further assistance or have any questions you can contact us by
telephone on: 01778 440803
Email:
info@rutlandcountygardenfurniture.co.uk
www.rutlandcountygardenfurniture.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>