RUTLAND COUNTY GARDEN FURNITURE SBSC1 Morcott Single Recycling Bin Store Instruction Manual

Table of Contents

RUTLAND-COUNTY-GARDEN-FURNITURE-SBSC1-Morcott-Single-Recycling-Bin-Store-
PROODUCT

Specifications

Product Name: Morcott Single Bin Store
Manufacturer: Rutland County Garden Furniture Ltd
Address: Ashbourne House, 2 Dovecote Meadows, Aslackby, Sleaford, Lincs, NG34 0HZ
Components: Refer to the list provided in the manual

Q: What tools are required for assembly?

A: You will need a 10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver), and 2 x 25mm wooden spacer blocks (included).

Q: How can I contact customer support for assistance?

A: For further assistance or questions, you can contact Rutland County Garden Furniture Ltd at 01778 440803.

Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to familiarise yourself with the assembly process and to also check that you have the correct components.
If for any reason you need assistance, you can find our contact details on the final page of these instructions.
We highly recommend that any assembly is carried out on an open flat, level surface if possible with sufficient space.

10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver), 2 x 25mm wooden spacer blocks (included).

RUTLAND-COUNTY-GARDEN-FURNITURE-SBSC1-Morcott-Single-Recycling-Bin-Store-
FIG-1

The Morcott Single Bin Store

Step 1

Begin by arranging the left panel (the one with the small wood block attached to the front post) and the back panel at 90° to each other, with the back panel raised up on the spacer blocks by approximately 25mm. Use 3 x shorter green screws to secure as shown.

Step 2

Now add the right-hand panel, fixing in the same way with 3 x shorter green screws.

Step 3

Carefully lay the assembly on its back and attach the metal bar to the front bottom edge of the 2 front posts as shown, securing in place with 2 x shorter green screws per post.

Step 4

Stand the assembly back up and lower the lid assembly into place so that the hinge bar is centred across the rear posts and fixed into place with a longer green screw into each post.

Step 5

Returning to the front of the store, place the finishing strip against the 2 front posts as shown with the screw holes configured to create a triangle and slide it upwards…

Step 6

until it is just touching the underside of the lid. Now fix both ends in place with 3 x shorter green screws per post.

Step 7

Align the door (hinge side on the left) so that the top edge clears the underside of the finishing strip by approx 10mm and each hinge leaf sits flat against the post with the knuckles resting against the front edge of the post. Secure the hinges in place using 8 x black screws.

Step 8

Position the cabin latch keep it on the post and align it horizontally with the latch as shown. Secure in place with 2 x black screws.

Step 9

Take the coach bolt from the prop fixing and push it through the hole in the prop, add a washer and then push through the hole in the lid batten as shown.

Step 10

Place another washer over the coach bolt and finally the securing nut. Tighten with a spanner or socket until fully tight and then back off until the prop is able to swing freely.

Step 11

If your bin lid has a suitable handle you may use the chain provided to attach this to the store lid. Undo the nut and slip one end over the coach bolt, then pass the other end through the handle and then over the end of the coach bolt, pulling the chain through until it is tight enough. Now reattach the nut.

Step 12

We hope that you found your product quick and easy to assemble but if not and you require any further assistance or have any questions you can contact us by telephone on: 01778 440803
Email: info@rutlandcountygardenfurniture.co.uk. www.rutlandcountygardenfurniture.co.uk.
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 11025348 VAT No: 282569762