KSANA Gold Bathroom Vanity 3 Light Instruction Manual

June 1, 2024
KSANA

KSANA Gold Bathroom Vanity 3 Light

KSANA-Gold-Bathroom-Vanity-3-Light-PRODUT

Specifications

  • Green ground screw (1)
  • Mounting plate (1)
  • Backplate (1)
  • Threaded ball (2)
  • Glass shade (3)
  • Socket (3)
  • Arm (1)

INSTALLATION

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

  1. We suggest installation by a licensed electrician.
  2. Please read the instructions carefully and save them as you may need them at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before the fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing the bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

KSANA-Gold-Bathroom-Vanity-3-Light-FIG-1

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

KSANA-Gold-Bathroom-Vanity-3-Light-FIG-2

PARTS INCLUDING

  • (C) Green ground screw (1)
  • (D ) Mounting plate (1)
  • (E) Back plate (1)
  • (F) Threaded ball (2)
  • (G) Glass shade (3)
  • (H) Socket (3)
  • (I) Arm (1)

ACCESSORIES ENCLOSED

  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and
    accessories are included as shown in the above illustration

  2. Turn off power
    Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.

  3. Make assembly

KSANA-Gold-Bathroom-Vanity-3-Light-FIG-4

  • Step A1: Unscrew the threaded ball(F) from the back plate(E) then gently remove the mounting plate (D).
  • Step A2: Secure mounting plate (D) to outlet box with mounting screws (A).
  • Step A3: Make wire connections
    Connect wires as below wires connecting shown below. TAKE NOTE OF THE WIRE COLOR OF FIXTURE,NEVER CONNECT WIRE TO GROUND WIRE
    KSANA-Gold-Bathroom-Vanity-3-Light-FIG-5

Twist the plastic wire connector until wires are tightly joined together, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  • Step A4: Align the holes in the back plate (E) with the mounting plate (D), then attach the back plate (E) using the previously removed threaded ball(F). Hand tighten until snug.
  • Step A5: Install bulbs (Not included. Please do not exceed the maximum capacity recommended on the socket.) Fix the glass shade (G) on the shrapnel under the socket (I) .

Check everything is installed properly, then you can turn on the light. Enjoy!

CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

FAQ

Q: Can I install this fixture myself?

A: We suggest installation by a licensed electrician to reduce the risk of fire, electric shock, or injury to persons.

Q: What should I do if I need replacement parts?

A: All parts for this fixture can be ordered from the place of purchase. Keep this sheet for future reference and use exact wording from the illustration when ordering parts.

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

KSANA User Manuals

Related Manuals