KSANA A03843 Gold Lantern Chandelier Instruction Manual

May 15, 2024
KSANA

KSANA A03843 Gold Lantern Chandelier

KSANA A03843 Gold Lantern Chandelier

Introduction

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

KSANA A03843 Gold Lantern Chandelier

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

  • Ladder

  • Phillips head, flat blade screwdriver

  • Electrical tape

  • Pliers

  • Wire cutter/ Stripper

PARTS TYPE & QTY INCLUDING

(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Collar ring (1)
(G) Collar loop (1)
(H) Quick link (2)
(I) Chain (1)
(J) Loop (1)
(K) Screw (8)
(L) Upper iron frame (1)
(M) Stem (1)
(N) Tube (4)
(0) Iron pipe (3)
(P) Steering joint (3)
(Q) Fixture loop assembly (1)
(R) Lower iron frame (1)

ACCESSORIES & QTY ENCLOSED

(A) Wire connector (3)
(B) Mounting screw (2)
Parts Type & Qty Including

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Make pre-installation
    Assembly & Installation Instructions:
    Step A1: Connect the upper iron frame (L) and lower iron frame (R) together with a tube (N) and secure with screws (K).
    Step A2: Adjust the steering joint (Pl to the vertical direction. Then push the iron pipe (O) down to the bottom of the
    steering joint (P).
    Step A3: Screw the stem (M) on the fixture loop assembly (Q) and fix it through the upper iron frame (L) with a loop (J).
    Assembly & Installation Instructions:
    Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain.
    Step B2: Attach the quick link (H) to connect the chain (I) and the loop(J) on the the top of upper iron frame (L).
    Step B3: Carefully lace the wires through the chain (l)(every other link)and stop just before you reach the top of chain (I).
    Gently pull the wires till snug.

  3. Turn off power
    Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done.
    A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).
    Place the wall switch in the” OFF” position.

  4. Make installation

    Step C1:
    .Attach the single bar {E) to outlet box with mounting screws {B). The side of single bar marked “GND” must face out
    Step C2: Raise the canopy {G) through screw collar loop {I) and screw the collar loop {I) to a proper position by measuring.
    Unscrew threaded ring {H) from screw collar loop {I) and remove the canopy (G). In this way, you would know the Proper position on which collar loop it should be located.
    Note: The canopy (G) should be snug against the ceiling and the collar loop (I) should be screwed enough threads (no less than 6 threads )over the threaded nipple (C) for more secure hanging .If not, adjust the collar loop (H)on the single bar assembly by screwing the collar loop (I) in or out of the single bar (E) until the length is achieved.
    Step C3: Slip the threaded ring(H) over the chain(K),then do the same with the canopy(G)
    Step C4: Open the quick link{J), attach the quick link (J) to connect the loop (I). Close the quick link(J).
    Pass the wires through screw collar loop(H) to the top of nipple(E) and gently pull till snug.
    Step CS: If needed, cut off the wires length of fixture. At this point, the remaining wire length measured from the top of single bar{B) is at least

  5. Step C6: Make wire connections
    Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE ,NEVER CONNECT
    WIRES TO GROUND WIRES
    Connect ground wire according to below chart

    Assembly & Installation Instructions:
    Connect wires according to below chart Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
    ---|---
    Black| White
    Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
    Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
    Insulated wire ( other than green)
    with copper conductor| Insulated wire ( other than green)
    with silver conductor
    *Note: When parallel wires ( SPT I & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus.)|

Twist plastic wire connector until wires are tightly joined together, wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box .
Step C7: Raise canopy (E) to ceiling and secure canopy (E) in place by tightening threaded ring (F) onto collar loop (G).
Step C8: Install the bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.)

  1. Check everything are already installed properly, then you could turn on the light. Enjoy!

CLEANING.
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS.
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals