KSANA HEALTH A03694 Farmhouse Faux Wood Flush Mount Ceiling Light Fixture Installation Guide

KSANA HEALTH A03694 Farmhouse Faux Wood Flush Mount Ceiling Light Fixture

Installation Guide

‘WARNING (To reduce the risk of fire, electric shock, or injury to

persons):

1. ‘We suggest installation by a licensed electrician.
2.  Please read the instruction carefully and save it as you may need it at later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Goto the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).Place the wall switch in the “OFF” position.
4.  Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Anygaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
8. ‘When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs gethot quickly.
9.  The safety instructions appearing in this manual are not meant to cover all possible conditions that may PN ooccur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED (NOT INCLUDED):

Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

(B) Round mounting plate (1)
(C) Green ground screw (1) (E) Canopy (1)
(F) Knob nut (2)
(G) Stem (1)
(H) Glass shade (1)
(1) Pplastic washer
(J) Iron washer (1)
(K) Hex nut (1)
(L) Flat cover (1)
(M) Column nut (1)

ACCESSORIES & QTY ENCLOSED:

(A) Plastic wire connector (3)
(D) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS:

1.  Carefully remove the fixture from the carton and check that all parts andaccessories are included as shown in the above illustration

2.  Turn off power
   Before you start to make installation, NEVER attempt any work without shutting off theelectricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position. B). Place the wall switch in the“OFF”position

3.  Unscrew the knob nuts(F) from mounting plate (B) .

4. Attach the mounting plate(B) to outlet box with the mounting screws(D).

5. Make wire connectionsr‘j‘» | OUTLET BOX
   Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE ,NEVER

CONNECT ‘WIRES TO GROUND WIRES

Connect ground wire according to below chart

Connect wires according to below chart

Raise canopy (E) to ceiling and secure canopy (E) in place by tightening knobs (F) onto the threaded nipple on mounting plate.

7. 1) Install the bulb (not included) (Please do not exceed the maximum capacity recommended on the socket.) 2) Rotate stem (G) on top of canopy (E) until tight.

8. 1) Pass the glass shade (H), plastic washer (I) and iron washer (J) through the il stem (G), then tighten with the hex nut (K).
2) Fix the flat cover (L) to the stem (G) with the column nut (M).

9. Check everything is already installed properly, then you could turn on the light. Enjoy !

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>