KSANA A03489 Gold Vanity Lights Instruction Manual

June 16, 2024
KSANA

KSANA A03489 Gold Vanity Lights

KSANA A03489 Gold Vanity Lights

WARNING

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

  1. We suggest installation by a licensed electrician.
  2. Please read the instruction carefully and save it as you may need it at later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
  4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
  6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
  7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
  8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.
    It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED)

Before doing assembly and installation please prepare the needed tools as below picture

Tools Required \(Not Included\)| | | | Tools Required \(Not Included\)
---|---|---|---|---
Ladder| Phillips head. fiat blade screwdriver| Electrical tape| Pliers| Wire cutter/Stripper

PARTS INCLUDING

( C ) Green ground screw (1)
( D ) Mounting plate (1)
( E ) Back plate (1)
( F ) Ball knob (2)
( G ) Socket cup (3)
( H ) Glass shade (3)
Parts Including

ACCESSORIES ENCLOSED

( A ) Mounting screw (2)
( B ) Plastic wire connector (3)
( I ) Iron bar (9)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration

  2. Turn off power
    Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.

  3. Make assembly
    | | Assembly & Installation Instructions
    ---|---|---
    |


Step A1:
Unscrew the studs(F) from the back plate(E) then gently remove the mounting plate (D).
Step A2: Secure mounting plate (D) to outlet box with mounting screws (A).
Step A3: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE Assembly & Installation
Instructions
Connect wires according to below chart


Connect Black or

Red Supply Wire to:

| Connect

White Supply Wire to:

---|---
Black| White
Parallel cord ( round & smooth )| Parallel cord ( square & ridged )
Clear, Brown, Gold or Black

without tracer

| Clear, Brown, Gold or Black

with tracer

Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green) with silver conductor
*Note: When parallel wires ( SPT I & SPT II ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus. )|

Twist plastic wire connector until wires are tightly joined together, wrap each connector with approved electrical
tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box .
Step A4: Align the holes in the back plate (E) with the mounting screws, then attach the back plate (E) using the previously removed studs(F). Hand tighten until snug.
Step A5: Install bulbs (Not included. Please do not exceed the maximum capacity recommended on the socket.)
Fix the glass shade (H) on the socket cup (G) with an iron bar (I).

  1. Check everything installed properly, then you could turn on the light. Enjoy !

CLEANING

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals