KSANA Modern Drum Chandelier Hanging Light Fixtures Instruction Manual
- May 15, 2024
- KSANA
Table of Contents
KSANA Modern Drum Chandelier Hanging Light Fixtures
IMPORTANT INFORMATION
- WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture
| | | |
---|---|---|---|---
Ladder
|
Phillips head.flat blade screwdriver
|
Electrical tape
|
Pliers
|
Wire cutter/Stripper
PARTS TYPE & QTY INCLUDING
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Collar ring (1)
(G) Collar loop (1)
(H) Quick link (2)
(I) Chain (1)
(J) Loop(1)
(K) Upper fixture loop assembly (1)
(L) Arm (3)
(M) Stem (1)
(N) Knob nut (3)
(O) Cloth lamp shade (1)
(P) Screw (3)
(Q) Lower fixture loop assembly (1)
ACCESSORIES & QTY ENCLOSED:
(A) Wire connector (3)
(B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make pre-installation
Step A1: Slip stem (M) over the wires and then thread it into the top of lower fixture loop assembly (Q).
Step A2 : Fix the stem (M) and loop (J) on the upper fixture loop assembly (K).
Step A3: Fix the cloth lampshade (O) and arm (L) together with screws (P) and knob nuts (N).
Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted part.
Step B2: Attach the quick link (H) to connect the chain (I) and the loop (J) on the the top of upper fixture loop assembly (K).
Step B3: Carefully weave the wires through the chain (I) (between every two links and one blank link) and stop just when you reach the top of chain (I). Gently pull the wires to ensure the wires are not stressed. -
͘Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B). Place the wall switch in the“OFF” position. -
installation
Step C1: Remove the collar ring (F) from collar loop(G). Attach the single bar (C) to outlet box with mounting screws (B).
Be sure that the side of single bar marked “GND” must face out, then unscrew the collar ring (F) from the collar loop.
Step C2 : Raise the canopy (E) through collar loop (G) and screw the collar loop (G) to measure the proper position.
Refer to the following note, you would know the proper position on which collar loop where should be located.
Unscrew collar ring (F) from screw collar loop (G) and remove the canopy (E).
Note: The canopy (E) should be snug against the ceiling and the collar loop (G) should be screwed enough threads (no less than 6 threads) over the threaded nipple for more secure hanging. If not, adjust the collar loop (G) on the single bar assembly by screwing the collar loop (G) in or out of the single bar (C) until the secure length is achieved.
Step C3: Slip the collar ring (F) over the chain (I), then do the same with the canopy (E).
Step C4: Open the quick link(H),attach the quick link (H) to connect the collar loop (G). Close the quick link(H). Pass the wires through the chain from the screw collar loop(G) to the top of nipple and gently pull the wires to ensure the wires are not stressed.
Step C5: If needed, cut the length of fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.
Step C6: Make wire connections
Connect wires as below wires connecting shown.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to below chart
Connect wires according to below chart Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord ( round & smooth)| Parallel cord ( square & ridged)
Clear,Brown,Gold or Black without tracer| Clear,Brown,Gold or Black with tracer
Insulated wire ( other than green) with copper conductor| Insulated wire ( other than green) with silver conductor
Note: When parallel wires ( SPTI & SPT ) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth ( see illus )|
Twist plastic wire connector until wires are tightly joined together, and wrap
each connector with approved electrical tape. Be sure that no wire strands are
exposed and then carefully tuck all wires into the outlet box.
Step C7 : Raise canopy (E) to ceiling and secure canopy (E) in place by
tightening collar ring (F) onto collar loop (G).
Step C8 : Install bulbs (not included) (Please do not exceed the maximum
wattage recommended on the socket.)
- Check . everything is already installed properly, then you could turn on the light. Enjoy!
CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials
such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>