KSANA Bathroom Light Fixtures Instruction Manual
- June 15, 2024
- KSANA
Table of Contents
KSANA Bathroom Light Fixtures Instruction Manual
WARNING (To reduce the risk of fire, electric shock, or injury to persons):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before fixture.
- Make sure the voltage you are using is 120V. The maximum wattage is Type B,Max 40W per bulb.
- Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in
the above illustration. -
Make pre-installation Step A1: Slip stem (O) over the wires and then thread it into the top of fixture loop (R). Slip Fixture body (M) overwires and then thread it onto the top of stem (O). Step A2: Open the Wood bending (N) and arm (Q) to 4 equal parts. Step A3: Slip orderly the upper cover (K) and fixture loop assembly (L) along wires then thread onto the fixture body (M) till tight. Fix the fixture loop assembly (L) and Bottom cover (T) on the Wood bending (N) with ball nut (S). Step B1: By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the remaining chain. Step B2: Attach the quick link (H) to connect the chain (I) and the loop(J) on the the top of upper cover (K). Step B3: Carefully lace the wires through the chain (I)(every other link)and stop just before you reach the top of chain (I). Gently pull the wires till snug
-
Turn off power Before you start to make installation, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B).Place the wall switch in the“OFF” position.
-
Make installation
Step C1: Remove the threaded ring (F) from collar loop(G). Attach the single
bar (C) to outlet box with mounting screws
(B). The side of single bar marked “GND” must face out ,Unscrew the collar
ring (H) from the collar loop.
Step C2: Pass canopy (E) over the mounted collar loop (G) then secure with
threaded ring (F) to test the height .
Unscrew threaded ring (F) from collar loop (G) and remove the canopy (E).
Note: The canopy (E) should be snug against the ceiling and the collar loop
(F) should be screwed enough threads (no less than 6 threads )over the
threaded nipple for more secure hanging .If not, adjust the height of nipple
and collar loop (G) until the desired height is reached. Remove the threaded
ring (F) and canopy (E) and place to the side.
Step C3: Slip the threaded ring(F) over the chain(I),then do the same with the
canopy(E).
Step C4: Open the quick link(H),attach the quick link (H) to connect the loop
(G). Close the quick link(H)
Pass the wires through screw collar loop(G) to the top of nippleand gently
pull till snug.
Step C5: If needed, cut off the wires length of fixture.At this point, the
remaining wire length measured from the top single bar(C) is at least 6″.
StepC6: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR WIRE COLOR OF FIXTURE ,NEVER CONNECT WIRE TO GROUND WIRE
Connect ground wire according to below chart
Connect wires according to below chart
Twist plastic wire connector until wires are tightly joined together,wrap each
connector with approved electrical
tape.Be sure that no wire strands are exposed and then carefully tuck all
wires into the outlet box .
Step C7: Raise canopy (E) to ceiling and secure canopy (H) in place by
tightening threaded ring (F) onto collar loop (G).
Step C8: Install bulbs (not included) (Please do not exceed the maximum
capacity recommended on the socket.)
5. Check everything is already installed properly, then you could turn on
the light. Enjoy!
CLEANING.
To clean, wipe fixture with a soft cloth. Do not use abrasive materials such
as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering parts.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>