ALPINE PXE-R80-8 8 Sound Track High Sound Quality Audio Processing Amplifier Owner’s Manual
- June 1, 2024
- Alpine
Table of Contents
- ALPINE PXE-R80-8 8 Sound Track High Sound Quality Audio Processing
- Specifications
- Product Usage Instructions
- FAQ
- Operating Instructions
- Copyright notice
- Tools that may be required (depending on the vehicle)
- Accessory list
- Diagram of device interfaces
- Wire pin arrangement
- Description of mobile APP
- Description of PC software
- Specification parameters
- Functional parameters
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ALPINE PXE-R80-8 8 Sound Track High Sound Quality Audio Processing
Amplifier
Specifications
- Model: PXE-R80-8
- Product Type: 8-Sound Track High-Sound-Quality Audio Processing Amplifier
- Compatibility: iPhone and Android devices
- Power Supply: 12V negative-grounded vehicles
Product Usage Instructions
Installation
To install the PXE-R80-8 amplifier, follow these steps:
- Ensure the vehicle is turned off and disconnect the battery.
- Mount the amplifier in a suitable location within the vehicle, ensuring proper ventilation.
- Connect the amplifier to the vehicle’s power supply according to the manufacturer’s instructions.
- Connect the audio input and output cables to the appropriate ports on the amplifier.
- Secure all connections and cables properly to avoid interference.
App Installation:
To control the device using the mobile app, follow these steps:
- For iPhone users, download the “Alpine Music” app from the App Store.
- For Android users, scan the QR code provided or download the app directly.
Usage:
After installation and app setup, you can use the amplifier as follows:
- Adjust sound settings using the mobile app for EQ, channel selection, delay, and frequency combination.
- Maintain a safe volume level while driving to ensure external noises are audible.
- If any issues arise, stop using the device immediately and seek professional assistance.
FAQ
-
What should I do if I encounter problems with the amplifier?
If you experience issues with the amplifier, stop using it immediately to prevent any personal injury or damage. Contact an authorized Alpine dealer or service center for repair. -
Can I wire and install the amplifier myself?
It is recommended to have professionals handle the wiring and installation of the product due to safety reasons. Contact your dealer for professional installation.
Operating Instructions
Type of precautions
-
Prohibition
Indicates a prohibited action (must not be performed). -
Prohibition
Indicates that disassembly is prohibited. -
Mandatory
Indicates a mandatory operation (must be performed).
Warning
-
In case of problems, please stop using the device immediately.
Otherwise, it may result in personal injury or damaged product. Please return the product to the authorized Alpine dealer or nearby Alpine service center to repair. -
The product is only suitable for the 12V negative-grounded vehicles.
Otherwise, it may lead to an accident like fire, etc. -
Please call the professionals to wire and install.
It needs professional expertise and experiences to wire and install the product. Please contact the dealer from whom you bought the product to install it for safety. -
Please do not disassemble or refit.
Otherwise, it may result in an accident, fire or electric shock. -
Small items like bolts or screws should be kept out of the reach of child.
If ingested, it may result in severe damage. Once ingested, please seek medical attention immediately. -
Please do not use any function that may distract you during driving.
Any function that may influence your attention should be used only when the vehicle is stopped completely. To use these functions, please first stop your vehicle in a safe area. Otherwise, it may result in an accident. -
During driving, you must maintain the volume at a level such that the noise outside can still be heard.
It is very dangerous not to clearly hear an emergency vehicle alarm and road warning signal (such as a railway crossing) and may result in an accident. Moreover, a too large volume may damage your hearing.
Caution
-
Product cleaning
Please clean the product regularly with a soft dry cloth. For any dirt difficult to clean, only water can be used to soak the cloth. Any other solvents may lead to dissolution. -
Temperature
Before starting the device, please ensure that the temperature inside the vehicle is between +60°C and -20°C. -
Repair
In case of problems, please do not repair them by yourself. Please return the product to the authorized Alpine dealer or nearby Alpine service center to repair. -
System matching
When PXE-R80-8 is used with active division mode to assign signals for speakers, please ensure that the frequency division point of high pitch is above 1500 Hz to avoid damage to high pitch speakers -
Installation site
The device cannot be installed at the following locations:- Under direct sunlight and near a hot source.
- With high humidity and near a water source.
- Dusty sites.
- Environments with violent vibration.
Copyright notice
The text mark and logo of Bluetooth® are the registered trademarks that Bluetooth SIG, Inc. Alpine Electronics has been authorized to use these text marks and logos. Other trademarks and names all belong to their holders.
Tools that may be required (depending on the vehicle)
Accessory list
Diagram of device interfaces
1
| External Bluetooth input interface| Select HD Bluetooth as the input signal,
or connect to the PXE-R80-8 mobile tuning APP. After the APP is successfully
connected, the Bluetooth icon is constant on.
---|---|---
2| USB 2.0 interface| A USB2.0 cable can be used to connect the computer and
perform tone tuning and setting in detail.
3| Wired controller interface| Volume adjustment, audio source selection and
data recall can be performed by connecting the wired controller.
4| Ambient light interface| Connecting the ambient light interface to control
the operation of ambient light.
5| RCA audio input| One set of RCA audio signal input which can connect the
RCA audio signal output of the vehicle audio player.
6| High-voltage-level input interface| Connected to the high-voltage-level
output of the vehicle audio player.
7
|
Input select switch interface
| If the switch is put to “ACC,” the device will be started by ACC. If put to
“HOST,” the device will be started by the high-voltage-level input signal
H1-/H1+.
8| Power lamp| Power lamp.
9| Protection display lamp| Protection display lamp.
10| High-voltage-level output interface| Connect the power amplifier output of
the device to speakers.
11| RCA audio out| Four sets of RCA audio signal output which can be connected
to the external power amplifier.
12| Vehicle audio player| Connect the vehicle audio player.
13| External power amplifier| Connect the external power amplifier
Wire pin arrangement
Description of mobile APP
Start page
1| Master volume| Drag and rotate the volume adjustment fader or click “+” and
“-” to adjust the master volume. The volume adjusting range is 0 ~ 35.
---|---|---
2| Mute button| Mute the master volume
3| Connection indicator| When the Bluetooth icon is red, the mobile phone
Bluetooth is not connected; when it is green, the mobile phone Bluetooth is
connected.
4
|
Menu bar
| You can encrypt data, protect DSP treble, set built-in power amplifier,
share sound effect, save sound effect, select online effect, select local
effect, set shutdown delay, check X- Over divider data (with channel setting
data available), reset device parameters, set EQ gain step size, set channel
gain step size, check device temperature, check device voltage and check
version number.
5| Interface selection| Five pages of different functions of tuning, namely
Homepage, EQ, Channel, Delay and Frequency combination.
Homepage
1| Master audio source| Switch master audio source (Bluetooth, high voltage
level and low voltage level).
---|---|---
2| Master audio source attenuation| The higher the attenuation of master audio
source, the lower the master volume is. The range of attenuation is 0% ~ 100%.
3| Auxiliary audio source| Switch auxiliary audio source (Bluetooth, high
voltage level, low voltage level and off).
4| Pre-set sound effects| Save or recall multiple pre-set sound effects.
EQ
1| Output channel| Slide left and right to select the output channel for EQ
adjustment. There are 8 channels to choose from.
---|---|---
2| Parametric EQ, Graphic EQ| Switch between Parametric EQ mode and Graphic EQ
mode. Mode switch would lead to loss of all settings.
3| EQ curve| Display the current EQ curve status, set the frequency, Q value
and gain.
4| Gain| Pull the fader up and down to adjust the gain. The adjustable range
is: -12.0dB ~
+12.0dB.
5
|
Allpass, Frequency, Q value, Gain
| Adjust the frequency, Q value and gain of the output channel. The frequency
and Q value are adjustable in the Allpass mode. The gain is adjustable but the
frequency and Q value are fixed in the Graphic EQ mode. The frequency, Q value
and gain are all adjustable in the Parametric EQ mode.
6| Reset EQ| Reset EQ setting.
7| Restore EQ, Direct EQ| Switch the tuned EQ data to direct state, click it
again to restore the EQ data before Direct EQ setting.
Channel
1 | Mute control | Select mute or unmute all channels with just one key. |
---|---|---|
2 | Channel volume | Push the fader left and right to adjust the channel volume |
in the range of -60dB ~ +6dB; click the speaker button to mute.
3| Channel phase| Select the channel phase (normal phase or reverse phase).
4| Channel type| Select the channel type in the pull-down menu.
5| Bass phase| Adjust the low pitch phase of output channel in the range of 0°
~ 360°.
6| Reset channel type| You can set the current channel type as Factory
setting.
7| Debugging| Select the debugging modes, including “Copy channel EQ / volume
from left to right” or “Copy channel EQ / volume from right to left”.
8| Divider| Turn on or off High-pass/Low-pass.
9| Filter type| Select filter type (Linkwitz-Riley, Butterworth or Bessel).
10| Frequency divider slope| Select the divider slope (-6dB/Oct, -12dB/Oct,
-18dB/Oct, -24dB/Oct, -30dB/Oct, – 36dB/Oct, -42dB/Oct, or -48dB/Oct).
11| Divider frequency| Select the divider frequency (between 20Hz and 20kHz).
Delay
1| Speaker| Select the speaker of the corresponding channel, click the speaker
to mute it, click it again to cancel mute.
---|---|---
2| Delay setting| Select the corresponding speaker, push the fader left and
right on the pop-up window to adjust the delay, or click “+” and “-” to adjust
the delay.
3| Unit of delay| Units of delay to choose from include ms, cm, and inch.
Adjusting range: 0.000 ~ 8.000 milliseconds, 0 ~ 277 centimeters, and 0 ~ 109
inches.
4| Delay group| There are 4 delay groups to choose from for each channel. You
can mute the channels and adjust the normal phase and reverse phase.
Frequency combination
1| Active or passive output| Keep the default setting as “Passive”.
Warning: if changed, you will lose the sound mixer setting of this channel.
---|---|---
2| Input channel| Push the fader left and right or press “+” and “-” to adjust
the volume of each audio source in the channel to achieve the purpose of sound
mixing and frequency mixing.
Description of PC software
Homepage
1 | Temperature display | Detect the temperature on the device surface. |
---|---|---|
2 | File | Load or save scene files on PC, and load or save all scene files. |
3
|
Options
| DSP treble protection, firmware update, noise gate, built-in power
amplifier, X-Over divider data (with channel setting data available), restore
factory settings, shutdown delay, switch between English and Chinese, check
the version number.
4| Encryption| Enter a 6-digit password to encrypt the tuned sound effect
data.
5| Device voltage display| Detect the system operation voltage.
6| Mute button| Mute the master volume
7| Master volume| Push the fader left and right to adjust the master volume in
the range of 0 ~ 35.
8
| Clipping distortion indicator| When the clipping
distortion indicator shows yellow, it reminds the user to adjust the device to
make the signal balanced and in a distortion-free state. When the adjustment
is completed, the indicator shows gray (gray by default).
9| Master audio source attenuation| The higher the attenuation of master audio
source, the lower the master volume is. The range of attenuation is 0% ~ 100%.
10| Pre-set sound effects| Multiple sets of pre-set sound effects can be saved
or recalled, and recall of online sound effects is supported.
11| Auxiliary audio source selection| Switch auxiliary audio source
(Bluetooth, high voltage level, low voltage level and off).
12| Master audio source selection| Switch master audio source (Bluetooth, high
voltage level and low voltage level).
13| Connection indicator| Connect the PC and the host machine with a USB
cable. Open the software to connect the device. Click it again to turn off the
connection.
EQ
1| EQ gain step size| Step size can be chosen from the range: 0.1dB ~ 0.5dB ~
1.0dB.
---|---|---
2| Output channel display| Display the output channel curve.
3| EQ curve| Display the current EQ curve status, adjust EQ graphics, set the
frequency, Q value and gain.
4
|
Allpass, Frequency, Q value, Gain
| Adjust the frequency, Q value and gain of the output channel. The frequency
and Q value are adjustable in the Allpass mode. The gain is adjustable but the
frequency and Q value are fixed in the Graphic EQ mode. The frequency, Q value
and gain are all adjustable in the Parametric EQ mode.
5| Parametric EQ, Graphic EQ| Switch between Parametric EQ mode and Graphic EQ
mode. Mode switch would lead to loss of all settings.
6
|
Low-pass filter
| Turn on or off the low-pass filter to cut off high frequency. Select filter type (Linkwitz-Riley, Butterworth or Bessel). Select the divider frequency (between 20Hz and 20kHz).
Select the divider slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, – 36dB/Oct, -42dB/Oct, or -48dB/Oct).
7
|
High-pass filter
| Turn on or off the high-pass filter to cut off low frequency. Select filter type (Linkwitz-Riley, Butterworth or Bessel). Select the divider frequency (between 20Hz and 20kHz).
Select the divider slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, – 36dB/Oct, -42dB/Oct, or -48dB/Oct).
8| Channel phase| Select the channel phase (normal phase or reverse phase).
9| Bass phase| Adjust the low pitch phase of output channel in the range of 0°
~ 360°.
10| Channel gain| Push the fader left and right to adjust the channel gain,
that it, to adjust the volume of the output channel; the adjustable range is:
-60dB ~ +6dB.
---|---|---
11| Debugging| Select “Copy channel EQ / volume from left to right” or “Copy
channel EQ / volume from right to left”.
12| Reset channel type| You can set the current channel type as Factory
setting.
13| Mute control| Select mute or unmute all channels with just one key.
14| Reset EQ| Reset EQ setting.
15| Restore EQ, Direct EQ| Switch the tuned EQ data to direct state, click it
again to restore the EQ data before Direct EQ setting.
16| Output channel| There are 8 output channels to choose from. Configure the
type of output channel. Click the speaker button to mute.
Delay
1| Delay setting| Select the corresponding speaker, push the fader left and
right to adjust the delay, or just enter the value to adjust the delay.
---|---|---
2| Unit of delay| Units of delay to choose from include ms, cm, and inch.
Adjusting range: 0.000 ~
8.000 milliseconds, 0 ~ 277 centimeters, and 0 ~ 109 inches.
3
|
Speaker, phase
| Select the speaker of the corresponding channel, and click the speaker to
mute it; and you can click it again to cancel mute. You can also adjust the
normal phase and reverse phase.
4| Delay group| There are 4 delay groups to choose from for each channel.
Frequency combination
1| Active or passive output| Keep the default setting as “Passive”.
Warning: if changed, you will lose the sound mixer setting of this channel.
---|---|---
2| Channel type| The settings of channel type selection are supported.
3| Input channel| Push the fader left and right or press “+” and “-” to adjust
the volume of each audio source in the channel to achieve the purpose of sound
mixing and frequency mixing.
Specification parameters
Dynamic range | ≥100dB |
---|---|
SNR (RCA) | ≥100dB |
Background noise | High-voltage-level: 95uVrms; RCA: 15uVrms |
Channel resolution | ≥80dB |
THD | ≤0.01% |
Input voltage | High-voltage-level: 28Vpp; RCA: 6Vpp |
Output voltage | RCA: 6Vpp |
Rated power | 8CH×35W (4Ω, 14.4V, 1kHz, 10%THD) |
Maximum power | 8CH×70W (4Ω, 14.4V, 1kHz, 10%THD) |
Input / output sensitivity (RCA) | 1:1 (no power amplification) |
Frequency response | 20Hz ~ 20kHz |
System sampling rate | 48kHz/24bit |
Input impedance | RCA: 15kΩ; high voltage level: 4.7Ω |
Output impedance | 51Ω |
Operating voltage | 9 ~ 16V |
Quiescent current | ≤3mA (in off state) |
Stand-by power consumption | ≤0.1W |
REM startup input | High voltage level (H1-/H1+), ACC optional |
REM startup output | 12V (0.2A) |
Startup time | 10s |
Operating ambient temperature | -20 ~ 70℃ |
Storage temperature | -40 ~ 85℃ |
Net weight | 2.4kg |
Dimensions | 216mm×204mm×47.5mm |
Functional parameters
Input signals| 6 channels of high-voltage-level, 2 channels of RCA audio and
high resolution Bluetooth
---|---
Output signals| 8 channels of high voltage level, and 8 channels of RCA audio
Signal gain of output channel| Range: mute, -60.0dB ~ +6.0dB
Output signal equalizer
| Type: parametric EQ, graphic EQ Frequency: 20Hz ~ 20kHz; resolution: 1Hz Q value (slope or gradient): 0.404 ~ 28.852
Gain: -12.0dB ~ +12.0dB; resolution: 0.1dB ~ 0.5dB ~ 1.0dB
Output signal frequency divider
| Each output channel is equipped with independent multi-order high-pass filter, Filter type: Linkwitz-Riley, Bessel or Butterworth
Filter cross-over frequency: 20Hz ~ 20kHz; resolution: 1Hz Filter slope (gradient): -6dB/Oct ~ -48dB/Oct
Output phase| Normal phase or reverse phase (0° ~ 360°)
Output delay| 0.000 ~ 8.000ms, 0 ~ 277cm, 0 ~ 109inch
Pre-set sound effects| Multiple sets of pre-set sound effects data can be
saved in the device, call of online sound effects is supported
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>