NUVO 65-623R1 Canopy Fixture Ceiling Light Installation Guide

NUVO 65-623R1 Canopy Fixture Ceiling Light

Product Information

Specifications:

• Models: 65-623R1, 65-624R1, 65-625R1, 65-626R1, 65-627R1,65-628R1, 65-629R1, 65-630R1, 65-631R1, 65-632R1
• Structure: DC motion sensor / DC PIR sensor
• Optional DC Motion Sensor

Product Usage Instructions

DC Motion Sensor Installation:
The motion sensor installation does not require tools. Simply follow these steps:

1. Locate a suitable mounting position for the sensor.
2. Attach the sensor securely to the desired surface using screws or adhesive.
3. Ensure the sensor is positioned correctly for optimal detection range.

Adjusting the Motion Sensor:

The motion sensor does not have a dialing code for adjustment.
Follow these steps to adjust it using a remote control (86/219):

1. Refer to the remote control instructions for specific adjustment settings.
2. Point the remote control towards the sensor and make necessary adjustments.
3. Test the sensor after adjustments to ensure proper functioning.

Frequently Asked Questions (FAQ):

Q: Do I need any special tools for installing the motion sensor?
A: No, the motion sensor installation does not require any special tools. You can mount it using screws or adhesive.

Q: How do I adjust the sensitivity of the motion sensor?
A: The motion sensor does not have a dialing code for adjustment. You will need a remote control (86/219) to make sensitivity adjustments. Refer to the remote control instructions for details.

INSTALLATION AND SAFETY INSTRUCTIONS

IMPORTANT: Read before installing fixture. Retain for future reference.

WARNING: Risk of Fire or Electric Shock

• To avoid damage, falling, electric shock or fire, do not modify the fixture or replace accessories without confirming with the supplier first.
• Only authorized, qualified personnel should install this fixture and should follow the owner’s manual. Any improper installation might cause failure, electric shock, fire or other injury, damage or hazard. The LED canopy light must be installed with UL listed liquid-tight conduit fittings.
• Disconnect power before installation or any maintenance of the fixture.
• Do not dismantle the fixture without the supplier’s authorization.
• Do not touch the power supply when the fixture is operating.
• The electrical fitting must be installed by a licensed electrician.
• For use in environments where an accumulation of non-conductive dust on the fixture may be expected.
• Use min 75° C supply.

IMPORTANT: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.

INSTALLATION

Ceiling Mount

1. Disassemble the driver box cover. Figure 1-1
2. Loosen the 3/4″ plug on the driver box cover with a screwdriver. Figure 1-2
3. Drill holes on the ceiling according to the fit plate. Figure 1-3
4. Fix the driver box cover on the ceiling. Figure 1-4
5. Attached the safety cord to the hook inside the back of the driver box once mounted. Figure 1-5
6. Connect the input line and ground; If the fixture is equipped with sensor, adjust !he sensor settings. Take relevant waterproof measures after the wires are connected. Figure 1-6
7. Align the drive box cover with he metal shrapnel inside the drive box and press upward to fasten it together. Figure 1-7
8. Lock the four screws, the product is installed. Figure 1-8

Pendant Mount

1. Disassemble the driver box cover. Figure 2-1
2. Loosen the 3/4″ plug on the driver box cover with a screwdriver. Figure 2-2
3. Fix the driver box cover on the 3/4 tube. Figure 2-3
4. Attached the safety cord to the hook inside the back of the driver box once mounted. Figure 2-4
5. Connect the input line and ground. If the fixture is equipped with sensor, adjust the sensor settings. Take relevant waterproof measures after the wires are connected. Figure 2-5
6. Align the driver box cover with the metal shrapnel inside the driver box and press upward to fasten it together. Figure 2-6
7. Lock the four screws, the product is installed. Figure 2-7

Ceiling Mount with Mounting Plate

1. Loosen screws with screwdriver, and detach the mounting plate. Figure 3-1
2. Align holes of the mounting plate with holes on ceiling. Fix the mounting plate to the ceiling with screwdriver. Figure 3-2
3. Thread the fixture wires through the mounting plate and connect with supply power wires (L/N/G). Hang the hook A in hole B;hang the hole C in hole D, and secure with mounting screws. Figure 3-3
4. Confirm the installation is secure before turning power on. Figure 3-4

WIRING DIAGRAM

Adjust the color temperature using the switch.
Move the switch left or right to select the desired color temperature.

Optional DC Motion Sensor
Motion sensor installation does not require tools.

NOTE: The motion sensor has no dialing code.
A remote control (86/219) is needed for adjustment. Refer to remote control instructions for adjustments.

DC Microwave sensor 86/218 – Max mounting height 39 feet,4 inches (12 meters)
DC PIR Sensors – 86/217 Max mounting height 19 feet, 6 inches
(6 Meters), 86/220 – Max mounting height 39 feet, 4 inches (12 meters)

NOTE: Sensors have a protective plastic cover over the pins that must be removed to make proper contact.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>