NUVO 60-7384 3 Light 20 inch Black/Burnished Brass Semi Flush Ceiling Light Installation Guide
- June 4, 2024
- NUVO
Table of Contents
ITEM NO: 60-7384
INSTALLATION AND SAFETY INSTRUCTIONS
60-7384 3 Light 20 inch Black/Burnished Brass Semi Flush Ceiling Light
The line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag-type fixture be installed on a
ceiling that contains a radiant-type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are
included as shown in the figure. Be careful not to misplace any of the screws
or parts, which are needed to install this fixture.
INSTALLATION
IMPORTANT: Do not attach the fixture directly to the outlet box.
STEP 1: Thread the mounting screw (A) into the matching holes in the
circular strap (B).
STEP 2: Secure the circular strap (B) to the outlet box with the outlet
box screws (C).
GROUNDING INSTRUCTIONS
STEP 1 : Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and connect the wires
according to the directions below:
GROUP A: Connect to Black House Wire| GROUP B: Connect to White House
Wire
---|---
BLACK| WHITE
“PARALLEL WIRE (round & smooth)| “PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN. GOLD OR BLACK WITHOUT TRACER| BROWN. GOLD OR BLACK WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or smooth
(seen best when viewed from the wire end.)
STEP 3: Take your fixture wire(s) from group A and place it evenly
against the black wire from the outlet box. Do NOT twist wires together before
using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check again for
a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside the outlet
box. Raise canopy (D) allowing the mounting screw (A) to protrude through the
hole in the canopy (D), and secure with finials (E).
STEP 2: Install lamp (F) (not supplied). Do not exceed the maximum
capacity recommended on the socket.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Do
not use abrasive materials such as scouring pads or powders, steel wool, or
abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustrations when
ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>